AKRAPOVIC C167 Evolution Titanium Exhaust Installation Guide
- September 17, 2024
- akrapovic
Table of Contents
C167 Evolution Titanium Exhaust
“`html
Specifications
-
Product: Akrapovic Evolution Line
-
Vehicle Compatibility: Mercedes AMG GLE 63/GLE 63 S Coupe (type
C167), Mercedes AMG GLE 63/GLE 63 S (type W167) -
Version: English Version 1.0
-
Date: 07/2024
Product Information
Congratulations on purchasing the Akrapovic product. The
Akrapovic product is made by Akrapovic d.d., Malo Hudo 8a, 1295
Ivancna Gorica, Slovenia.
Please read this entire installation manual carefully prior to
installing and using the Akrapovic product.
If you have any questions regarding the installation and/or
proper use of the Akrapovic product or this manual, please contact
your local Akrapovic partner.
For more information on the Akrapovic products, see the official
Akrapovic website at: www.akrapovic.com
Safety and Compliance
Your safety is our number one priority. Please drive your car
responsibly, safely and always obey local traffic rules.
The product may only be used in accordance with relevant laws
and regulations, including state and federal, where applicable.
Installation Instructions
DAMAGE caused by improper installation, use, and maintenance of
the Akrapovic product is not covered by the Akrapovic warranty.
Please refer to the enclosed warranty with regard to the terms of
our warranty. Technical specifications of Akrapovic products are
subject to change without notice.
Copyright and Other Rights Notice
SAFETY AND COMPLIANCE WARNING, PLEASE READ CAREFULLY
BEFORE REMOVING THE STOCK PARTS AND BEGINNING THE INSTALLATION
OF YOUR NEW AKRAPOVIC PRODUCT, PLEASE MAKE SURE THAT ALL ITEMS
LISTED BELOW ARE VERIFIED:
Noise and Emission Warnings
General warning: Because of the world-wide distribution of
Akrapovic d.d. products, neither Akrapovic d.d. nor any of its
subsidiaries make any representation that the products comply with
the air and/or noise emissions laws, or labeling laws, of any
jurisdiction.
The purchasers are entirely responsible for informing themselves
of the applicable laws where the products are to be used and to
comply with those laws.
Frequently Asked Questions (FAQ)
Can I install the Akrapovic product myself?
It is recommended to have the product installed by a
professional to ensure proper installation and avoid any damage
that may not be covered by the warranty.
Where can I find more information about legal
compliance?
You can visit the official Akrapovic website or refer to the
enclosed certificate for EC and ECE type approvals.
“`
Installation instructions
Akrapovic Product: Evolution Line for the Mercedes AMG GLE 63/GLE 63 S Coupe
(type C167) Mercedes AMG GLE 63/GLE 63 S (type W167)
ENGLISH Version 1.0
07/2024
www.akrapovic.com
D249.1.00.0000 H
Installation instructions
Akrapovic Product: Evolution Line for the Mercedes AMG GLE 63/GLE 63 S Coupe
(type C167) Mercedes AMG GLE 63/GLE 63 S (type W167)
ENGLISH Version 1.0
07/2024
www.akrapovic.com
D249.1.00.0000 H
www.akrapovic.com
Congratulations on purchasing the Akrapovic product. The Akrapovic product is
made by Akrapovic d.d., Malo Hudo 8a, 1295 Ivancna Gorica, Slovenia
(“Akrapovic”).
Please read this entire installation manual carefully prior to installing and
using the Akrapovic product.
Akrapovic product should only be installed by persons skilled in car exhaust
system or other car parts installation and performance. The instructions
provided in this manual should be followed to ensure proper installation and
safe use of the Akrapovic product. Akrapovic and/or its partners shall not be
held liable for any damage or personal injury (including direct, indirect, or
consequential damage) sustained as a result of improper installation of the
Akrapovic product or its use and maintenance contrary to the instructions and
warnings contained herein.
If you have any questions regarding the installation and/or proper use of the
Akrapovic product or this manual, please contact your local Akrapovic partner.
For more information on the Akrapovic products, see the official Akrapovic
website at: http://www.akrapovic.com
GENERAL INFORMATION
Your safety is our number one priority. Please drive your car responsibly,
safely and always obey local traffic rules.
All statements made with regard to the product’s compliance are made in
respect of the product “as is”. Any modifications of the Akrapovic product or
its improper installation, use or maintenance that is not in accordance with
this Installation manual, may result in severe damage to the product, vehicle
and/ or engine, as well as personal injury, and may affect the product’s
compliance with the legal requirements, such as product’s air and/ or noise
emissions (as an example, the car may not be suitable for use on public roads
any longer), as well as warranty coverage.
The product may only be used in accordance with relevant laws and regulations,
including state and federal, where applicable.
4 / 100
Damage caused by improper installation, use and maintenance of the Akrapovic
product is not covered by the Akrapovic warranty. Please refer to the enclosed
warranty with regard to the terms of our warranty. Technical specifications of
Akrapovic products are subject to change without notice.
COPYRIGHT AND OTHER RIGHTS NOTICE
The Akrapovic trademark, including corporate logos and emblems, are subject to
copyright as well as trademark rights of Akrapovic, its licensors, or third
persons authorizing Akrapovic to use them. Any reproduction, technical or
other manipulation, translation, or other use of the copyright and/or
trademark rights contained herein is prohibited without the explicit prior
written consent of Akrapovic. The same especially applies to the entire
contents of this manual and/or any of its parts, including but not limited to
technical specifications, instructions, graphs, photographs, and so on
included in this manual. Akrapovic takes all copyright and other rights
infringement cases under serious consideration. If you have any reason to
believe that your product is not an original Akrapovic product, please contact
our local partners or Akrapovic at info@akrapovic.com.
5 / 100
www.akrapovic.com
SAFETY AND COMPLIANCE WARNING, PLEASE READ CAREFULLY
BEFORE REMOVING THE STOCK PARTS AND BEGINNING THE INSTALLATION OF YOUR NEW
AKRAPOVIC PRODUCT, PLEASE MAKE SURE THAT ALL ITEMS LISTED BELOW ARE VERIFIED:
· This manual is specific to the car indicated on the cover page, for which it
is designed. Installation procedures vary depending on the type of car. Please
verify that the Akrapovic product and this installation manual correspond to
the type of your car.
· For exhaust system only: the exhaust system can get extremely hot during and
after it is used. Make sure not to touch the exhaust system until it is
completely cool. Allow the exhaust and engine to cool down before beginning
installation.
· Make sure the car is securely positioned to prevent damage to yourself and
other, or the car. · Please check the parts you recieved against the parts
list available on our website (please
use the QR code on the front page or look for “schematic view” in the
respective product page on www.akrapovic.com). Make sure that you have all the
parts necessary for the installation of your new Akrapovic product. If any of
the parts is missing, please do not proceed with uninstalling your stock
parts/installing the Akrapovic product and contact the retailer where you
purchased the Akrapovic product. · For exhaust system only: every exhaust
system has its unique serial number, which identifies the authenticity of the
product. You can find the serial number on the exhaust system. Please refer to
the picture 1. Please verify that your exhaust system is an original Akrapovic
product. If you have any doubts, please contact the reseller where you
purchased the exhaust system or Akrapovic partners. This manual, any
certificates and Akrapovic warranty apply to original products only.
GENERAL NOTE
Photographs and other illustrations in this manual are symbolic and are
intended to help represent individual steps for proper installation and use,
as well as for a general overview. The actual component parts of the Akrapovic
product may not entirely correspond to the photographs and other
illustrations.
6 / 100
Picture 1 – SERIAL NUMBER POSITIONS:
7 / 100
www.akrapovic.com
NOISE AND EMISSION WARNINGS
General warning Because of the world-wide distribution of Akrapovic d.d.
products, neither Akrapovic d.d. nor any of its subsidiaries make any
representation that the products comply with the air and/or noise emissions
laws, or labeling laws, of any jurisdiction. The purchasers are entirely
responsible for informing themselves of the applicable laws where the products
are to be used and to comply with those law.
Although legal compliance of Akrapovic products in a specific country should
be determined by the user, you can find some basic guidance on compliance of
your Akrapovic product with various legal requirements on the product-related
part of our website (please use the QR code on the front page or look for the
respective product page on www.akrapovic.com). For EC and ECE type approvals,
please refer to the certificate enclosed to your product.
USA WARNING
Various U.S. states and the U.S. federal government have individual laws
regulating the use of aftermarket parts and systems, especially as those parts
and systems modify, remove, or replace original equipment catalysts. Please
consult the appropriate laws in your area before installing any aftermarket
part or system on your vehicle to ensure compliance with all applicable laws.
Neither Akrapovic d.d. nor any of their subsidiaries or the sellers of the
parts or systems make any representation that any of their parts or systems
comply with any such laws.
CALIFORNIA WARNING
California laws prohibit the use of any aftermarket part or system that
modifies, removes or replaces original equipment catalysts unless the
California Air Resources Board has issued an Executive Order regarding such
part or system or unless the part or system is exempted by being used only on
racing vehicles on closed courses. Neither Akrapovic d.d. nor any of their
subsidiaries make any representation that any of their parts or systems has
received such an Executive Order or that any of their parts or systems conform
with the racing vehicles exemption. The purchasers are entirely responsible
for informing themselves of applicable California laws and to comply with
those laws.
8 / 100
SYMBOLS
The following symbols are used throughout these installation instructions:
TOOLS AND PROTECTIVE EQUIPMENT REQUIRED
TIGHTENING TORQUE
LUBRICATION
HAND TIGHTEN
INSTALLATION TIP
CAUTION OR IMPORTANT
USE BOLT SEALANT Apply 3 to 4 small drops of bolt sealant onto the cleaned and
degreased threads before tightening the bolts. WARNING! Avoid contact with
skin, eyes and mucous membranes. Do not inhale fumes. Keep out of reach of
children.
USE ANTI-SEIZE LEAD-FREE COPPER PASTE (black tube) Provides trouble-free and
long-lasting protection against seizing, corrosion and rusting of bolts,
threaded ends, nuts, joints, etc. Also protects against vibration, wear and
impact. WARNING! Avoid eye contact. Keep out of reach of children.
USE ANTI-SEIZING GREASE (white tube) Prevents seizing, corrosion and excessive wear between the titanium components. WARNING! Avoid eye contact. Keep out of reach of children.
9 / 100
www.akrapovic.com
Tools & equipment
· mechanic gloves · eye protection · Pipe cutting tool · Torx 30 · Torx 40 ·
Torx CTX40 · Torx E12 · Socket 15 mm · Socket 17 mm · T-handle 8 mm wrench ·
T-handle 10 mm wrench · Rubber bracket unhooking tool · Flat screwdriver ·
Cross-head screwdriver · Cutting nippers
PARTS LIST
The packaging box should contain one or more of the following items:
·
Akrapovic product
·
Homologation certificate/ compliance documents if applicable
·
Warranty
·
Fitting material
·
Installation Manual
Detailed list of parts can be found on the Akrapovic website (please use the QR code on the front page or look for “Schematic view” in the respective product page on www.akrapovic.com).
10 / 100
IMPORTANT: The car should be in the off position throughout the dismounting
and installation process, as well as any other work done on the Akrapovic
product!
REMOVAL OF STOCK EXHAUST SYSTEM OR OTHER VEHICLE’S STOCK PARTS:
The process of uninstalling the original exhaust system or other parts may
vary depending on the existing exhaust system or other vehicle parts. Please
follow the original vehicle manufacturer’s workshop manual for uninstalling
the original exhaust system or other parts. If you for any reason decide
otherwise, please note that any information provided in this respect herein
should be considered as general information provided for your convenience
only. Akrapovic shall not assume any liability or responsibility with regard
to uninstalling your existing exhaust system or other parts, warranty coverage
of such exhaust system or other parts vehicle or their further fitness for
use. In case your Akrapovic exhaust system or other vehicle parts may not be
used on certain roads or under certain conditions, please keep the stock (or
other) exhaust system or other parts that you can use in such circumstances
legally.
11 / 100
www.akrapovic.com
REMOVAL OF STOCK EXHAUST SYSTEM: 1. Put the vehicle onto a car lift (F 01).
CAUTION: ensure that the car is lifted safely and properly in order to avoid
the risk of vehicle damage, injury, or even death! CAUTION: make sure not to
injure yourself or damage any part of the vehicle during this process!
F 01
12 / 100
2. Mark the stock exhaust system at marked positions, exactly as shown.
Carefully cut the pipes at the marked cutting lines, using pipe cutting tool
or equivalent (F 02, 03, 04). CAUTION: make sure not to injure yourself or
damage any part of the vehicle during this process!
F 02
13 / 100
www.akrapovic.com
76 mm 2,99 in
CUTTING LINE
CUTTING LINE
72 mm 2,8 in
F 03
14 / 100
F 04
15 / 100
www.akrapovic.com
3. Support the exhaust system, unscrew the front rubber brackets, disconnect
all three exhaust valve actuators, unscrew the muffler’s rubber brackets and
carefully remove the exhaust system off the vehicle (F 05, 06, 07, 08, 09).
CAUTION: make sure not to injure yourself or damage any part of the vehicle
during this process! CAUTION: support the muffler during this process or you
could injure yourself or damage the vehicle!
F 05
16 / 100
F 06
17 / 100
www.akrapovic.com
F 07
18 / 100
F 08
19 / 100
www.akrapovic.com
F 09
20 / 100
4. Unscrew and remove both tail pipes off the bumper (F 10, 11, 12, 13).
IMPORTANT: make sure, not to damage the bumper or tail pipes during this
process!
GLE S Coupe:
F 10
21 / 100
www.akrapovic.com
GLE S Coupe:
F 11
22 / 100
GLE / GLE S:
F 12
23 / 100
www.akrapovic.com
GLE / GLE S:
F 13
24 / 100
5. Carefully remove rubber brackets and unscrew all three exhaust valve
actuators off the stock exhaust system (F 14, 15, 16, 17, 18). CAUTION: make
sure not to injure yourself or damage any part of the system during this
process! INSTALLATION TIP: for easier dismounting, lubricate the rubber
brackets (WD40®). WD-40® is a trademark of the WD-40 Company.
F 14
25 / 100
www.akrapovic.com
F 15
26 / 100
F 16
27 / 100
www.akrapovic.com
F 17
28 / 100
F 18
29 / 100
www.akrapovic.com
6. Open the trunk, remove the cargo cover, fold the rear backrests, remove
the trunk floor panel, car emergency kit, loading sill cover, trunk floor
panel, right and left trunk trim panels (to get access to vehicle electrical
wiring harness) and remove the marked rubber gromet; check vehicle
manufacturer workshop manual for details (F 19, 20, 21, 22, 23, 24, 25, 26,
27, 28, 29, 30, 31, 32, 33). CAUTION: make sure not to injure yourself or
damage any part of the vehicle during this process! GLE / GLE S:
F 19
30 / 100
GLE / GLE S:
F 20
31 / 100
www.akrapovic.com
GLE S Coupe:
F 21
32 / 100
GLE S Coupe:
F 22
33 / 100
www.akrapovic.com
F 23
34 / 100
F 24
35 / 100
www.akrapovic.com
F 25
36 / 100
F 26
37 / 100
www.akrapovic.com
F 27
38 / 100
F 28
39 / 100
www.akrapovic.com
F 29
40 / 100
F 30
41 / 100
www.akrapovic.com
F 31
42 / 100
F 32
43 / 100
www.akrapovic.com
RUBBER GROMMET
F 33
44 / 100
7. Unscrew the marked nuts and bolts and remove the drive shaft heat shield
(F 34). CAUTION: make sure not to injure yourself or damage any part of the
vehicle during this process!
F 34
45 / 100
www.akrapovic.com
8. Unscrew the marked nuts and bolts and remove the muffler heat shield (F
35). CAUTION: make sure not to injure yourself or damage any part of the
vehicle during this process!
F 35
46 / 100
9. Unscrew the marked nuts and carefully remove the marked, right under-floor
panel (F 36, 37). CAUTION: make sure not to injure yourself or damage any part
of the vehicle during this process!
F 36
47 / 100
www.akrapovic.com
F 37
48 / 100
10. Unscrew and remove the right rear wheel (F 38). CAUTION: make sure not to
injure yourself or damage any part of the vehicle during this process!
F 38
49 / 100
www.akrapovic.com
11. Unscrew the market clips and nuts and remove the rigt wheel arch trim (F
39). CAUTION: make sure not to injure yourself or damage any part of the
vehicle during this process!
F 39
50 / 100
INSTALLATION OF THE AKRAPOVIC EXHAUST SYSTEM:
1. The Control Kit components (F 40):
11 – Controller TNG
44 – To right stock valve connector 77 – To front stock valve connector
22 – CAN sniffer
55 – To left valve actuator
88 – To front valve actuator
33 – To right valve actuator 66 – To left stock valve connector
3 4
2
F 40
51 / 100
1 7
8
Akr. rubber grommet
6 5
www.akrapovic.com
2. Disconnect the B2 and B3 connectors from TNG controller; lead the harness
into the trunk (make sure, that Akrapovic grommet plugs into place correctly)
then lead the left, right and front actuators’ harnesses to the actuators’
locations, connect the Akrapovic connectors to the stock connectors as shown
and secure the harness and connectors, using tie wraps from Akrapovic
installation kit (F 41, 42, 43, 44, 45, 46, 47, 48, 49).
IMPORTANT: make sure to secure the harnesses and connectors in such a way,
that they won’t touch any hot or moving parts of the vehicle!
Akr. rubber grommet
F 41
52 / 100
TIE WRAP
F 42
53 / 100
www.akrapovic.com
4 3
6 5
7
8
F 43
54 / 100
4 3
F 44
55 / 100
6 5
www.akrapovic.com
TIE WRAP
TIE WRAP
6 CLICK!
5
F 45
56 / 100
TIE WRAP
CLICK!
4 3
F 46
57 / 100
www.akrapovic.com TIE WRAP
TIE WRAP
5 6
F 47
58 / 100
TIE WRAP
7 8
F 48
59 / 100
TIE WRAP
www.akrapovic.com
TIE WRAP CLICK!
7
8
F 49
60 / 100
3. Install and connect the Controller TNG and CAN sniffer components in the
trunk, as shown; secure all wiring, reconnect the B2 and B3 connectors to the
Controller TNG unit and tuck the unit as shown (F 50, 51, 52, 53, 54, 55, 56,
57).
IMPORTANT: make sure to secure all Control Kit components in such a way, that
they won’t touch any hot or moving parts of the vehicle!
2
1
F 50
61 / 100
www.akrapovic.com
CLICK!
CLICK!
CLICK!
F 51
62 / 100
F 52
63 / 100
www.akrapovic.com
IMPORTANT: carefully separate the BLUE and BLUE-WHITE wires from the marked
harness, unscrew the CAN sniffer’s cover, lead the blue and blue-white wires
through the CAN sniffer’s wire grooves as shown and reinstall the cover (F 53,
54, 55, 56, 57). IMPORTANT: make sure not to damage the wires during this
process
F 53
64 / 100
F 54
65 / 100
BLUE-WHITE WIRE
BLUE WIRE
www.akrapovic.com
F 55
66 / 100
BLUE WIRE
BLUE-WHITE WIRE
F 56
67 / 100
www.akrapovic.com
F 57
68 / 100
4. Reinstall removed drive shaft and muffler heat shields; check vehicle
manufacturer workshop manual for correct procedures and tightening torques.
5. Install, adjust and tighten the Akrapovic tail pipes into the bumper,
using stock bolts; check vehicle manufacturer workshop manual for correct
tightening torque (F 58, 59, 60, 61). IMPORTANT: make sure not to damage the
bumper or tail pipes during this process! GLE S Coupe:
F 58
69 / 100
www.akrapovic.com
GLE S Coupe:
F 59
70 / 100
GLE / GLE S:
F 60
71 / 100
www.akrapovic.com
GLE / GLE S:
F 61
72 / 100
6. Install stock front valve actuator with stock harness bracket (using M5x20
bolts and M5 nuts from Akrapovic installation kit), double clamps from
Akrapovic installation kit and stock rubber brackets onto the link pipes, as
shown (F 62, 63, 64, 65). INSTALLATION TIP: for easier mounting, lubricate the
original rubber bracket (WD40®). WD-40® is a trademark of the WD-40 Company.
F 62
73 / 100
www.akrapovic.com
IMPORTANT: orient the stock harness bracket, as shown! IMPORTANT: use
Akrapovic bolt sealant on the actuator’s bolts threads!
STOCK BRACKET
4,9Nm 3.6ftlb
F 63
74 / 100
F 64
75 / 100
www.akrapovic.com
INSTALLATION TIP: for easier mounting, lubricate the rubber brackets (WD40®).
WD-40® is a trademark of the WD-40 Company.
F 65
76 / 100
7. Slide the link pipes onto the stock pipes; tighten the front rubber
brackets onto the chassis (check the manufacturer’s workshop manual for
correct tightening torque), align the pipes in respect to the chassis, center
the double clamps and tighten them to the specified torque and connect the
front actuator’s connector and secure the harness and connector as shown (F
66, 67, 68, 69). CAUTION: make sure not to injure yourself or damage the link
pipes during this process!
F 66
77 / 100
www.akrapovic.com
22Nm 16ftlb
F 67
78 / 100
F 68
79 / 100
34Nm 25ftlb
www.akrapovic.com
CLICK! F 69
80 / 100
8. Slide the double clamps from Akrapovic installation kit onto the link
pipes’ outlets (F 70). CAUTION: make sure not to injure yourself or damage any
part of the vehicle during this process!
F 70
81 / 100
www.akrapovic.com
9. Assemble the stock rubber brackets and stock exhaust valve actuators
(using M5 nuts from Akrapovic installation kit) onto the Akrapovic muffler, as
shown (F 71, 72, 73). INSTALLATION TIP: for easier mounting, lubricate the
rubber brackets (WD40®). WD-40® is a trademark of the WD-40 Company.
F 71
82 / 100
IMPORTANT: make sure not to mix the actuators! Put them on the same valves as
they were on stock exhaust system! IMPORTANT: use Akrapovic bolt sealant on
the actuators’ nuts threads!
4,9Nm 3.6ftlb
F 72
83 / 100
www.akrapovic.com
F 73
84 / 100
10. Carefully slide the muffler onto the link pipes, tighten the rubber
brackets onto the chassis (using stock bolts), connect the valve actuators and
secure the harnesses as shown, align the muffler in respect to the chassis,
align the clamps and tighten them to the specified torque (F 74, 75, 76, 77).
CAUTION: make sure not to injure yourself or damage the muffler during this
process!
F 74
85 / 100
www.akrapovic.com
22Nm 16ftlb
F 75
86 / 100
CLICK!
F 76
87 / 100
www.akrapovic.com
34Nm 25ftlb
F 77
88 / 100
11. Reinstall all dismounted stock parts (wheel arch trim, wheel, right
under-floor panel, trunk trim etc.); check vehicle manufacturer workshop
manual for correct procedures and tightening torques (F 78, 79, 80). CAUTION:
make sure not to injure yourself or damage any part of the vehicle during this
process!
F 78
89 / 100
www.akrapovic.com
GLE S Coupe:
F 79
90 / 100
GLE/GLE S:
F 80
91 / 100
www.akrapovic.com
FINAL INSTALLATION: IMPORTANT: reinstall the dismounted or partially removed
stock parts (wheel arches, bumper etc.); check vehicle manufacturer workshop
manual for correct procedures and tightening torques.
IMPORTANT: make sure all the nuts and bolts are sufficiently tightened. In
case the Akrapovic product touches the cowling or other parts, repeat the
adjustment of the product or contact your authorized dealer.
IMPORTANT: clean all Akrapovic product’s surfaces before the first start of
the engine or the stains will burn onto the surfaces!
IMPORTANT: in case any component of the Akrapovic product is equipped with DMC
code sticker, the sticker and glue residue should be removed from the
component, before first use!
MAINTENANCE OF THE AKRAPOVIC PRODUCT: 1. Clean all Akrapovic product’s
surfaces. Cleaning will prevent spots from burning onto the
surface. Do not use aggressive chemical cleaners, because they can damage the
surface: · Titanium surfaces (titanium muffler’s outer sleeve, titanium pipes
etc): use a soft cloth
sprayed with a multi-purpose spray lubricant (WD-40® or equivalent), then
wipe with a soft dry cloth.
· Carbon-fiber surfaces (carbon-fiber outlet cap, carbon-fiber muffler’s outer
sleeve, carbon-fiber bracket etc): use a soft dry cloth sprayed with all
purpose foam cleaner, then wipe with a soft dry cloth.
· Painted surfaces (painted outlet cap, painted muffler’s outer sleeve,
painted bracket etc): use a soft cloth sprayed with all purpose foam cleaner,
then wipe with a soft dry cloth.
· Chrome plated surfaces (chrome plated outlet cap, chrome plated muffler’s
outer sleeve etc): use a soft cloth sprayed with all purpose foam cleaner,
then wipe with a soft dry cloth.
· Stainless steel surfaces (stainless steel muffler’s outer sleeve, stainless
steel pipes etc): use a soft cloth sprayed with a contact cleaner, then wipe
with a soft dry cloth.
WD-40® is a trademark of the WD-40 Company.
2. Periodically check if all the Akrapovic product’s nuts and bolts are
sufficiently tightened.
92 / 100
IMPORTANT: IT IS NORMAL FOR WHITE SMOKE TO COME OUT OF THE MUFFLER AT FIRST
OPERATION.
CAUTION: DO NOT STAND BEHIND THE MUFFLER AT ANY TIME.
IMPORTANT: DO NOT USE AUTOMOTIVE WHEEL CLEANERS OR ANY CLEANING PRODUCTS WHICH
CONTAIN ACIDIC ADDITIVES TO CLEAN THE AKRAPOVIC EXHAUST SYSTEMS.
IMPORTANT: WE RECOMMEND HIGH CAUTION WHEN USING POWER / PRESSURE WASHER FOR
CLEANING PAINTED / LACQUERED SURFACES OF THE AKRAPOVIC COMPONENTS, TO AVOID
PAINT / LACQUER DAMAGE.
IMPORTANT: SOME OF THE AKRAPOVIC CARBON FIBER COMPONENTS ARE ADDITIONALLY
PROTECTED AGAINST ROCK CHIPS WITH CLEAR LACQUER PROTECTION FILM. THE
PROTECTION FILM IS AVAILABLE AS SPARE PART BY AKRAPOVIC COMPANY. THE
PROTECTION FILM IS NOT THE SUBJECT OF THE AKRAPOVIC WARRANTY.
IMPORTANT: ALL AKRAPOVIC PRODUCTS ARE DEVELOPED AND DESIGNED TO BE USED ON
SPECIFIC VEHICLES, FOR THEIR ENTIRE EXPECTED LIFETIME. PLEASE MAKE SURE THAT
END-OF-LIFE AKRAPOVIC PRODUCT IS DISASSEMBLED TO COMPONENTS SHOWN IN THE
PRODUCT’S SCHEMATIC DIAGRAM AVAILABLE ON THE AKRAPOVIC WEBSITE AND EACH
COMPONENT SCRAPPED RESPONSIBLY AND ACCORDING TO APPLICABLE LOCAL LAWS AND
REGULATIONS. AKRAPOVIC DOES NOT ASSUME ANY OBLIGATION OR RESPONSIBILITY WITH
RESPECT TO THE SCRAPPING PROCESS OR PROVIDING INFORMATION RELATED THERETO.
IMPORTANT: IN CASE OF CONTAMINATION WITH GASOLINE, ALL PAINTED/LACQUERED
SURFACES OF THE AKRAPOVIC COMPONENTS MUST BE WIPED WITH SOFT, ABSORBENT CLOTH
IMMEDIATELY!
93 / 100
www.akrapovic.com
CAUTION: THE EXHAUST SYSTEM CAN BE EXTREMELY HOT. ALLOW THE EXHAUST AND ENGINE
TO COOL DOWN BEFORE BEGINNING INSTALLATION OR ANY OTHER WORK ON THE EXHAUST
SYSTEM. THIS MANUAL IS SPECIFIC TO THE MERCEDESAMG GLE 63 TYPE W167 AND GLE S
COUPE 63 TYPE C293. THERE MAY BE SOME DIFFERENCES IN INSTALLATION PROCEDURES
FOR OTHER MODELS.
94 / 100
TROUBLESHOOTING: Problem
Possible cause
Exhaust gas leaks out of the muffler/pipe clamp connections
loosened clamp
connection is not completely joined
No supply
Valves are not moving
Error detected
Solution tighten the clamp to specified torque
tap the connection into place and tighten the clamp to specified torque
Check green LED on the Controller TNG.
If the LED is off:
·
Check electrical connection
and connectors
· valves
Check fuse for exhaust
Check green LED on the Controller TNG.
If the LED is continuously ON:
·
There are no errors
detected.
If the LED is continuously blinking:
·
There is an error detected.
Connect the Controller TNG to PC via
USB cable and use Akrapovic Tools
diagnostic utility. This action can be
performed only by authorized Akrapovic
dealers.
95 / 100
www.akrapovic.com
DECLARATION OF CONFORMITY OF CONTROLLER TNG
COMPANY: ADDRESS:
Akrapovic d.d. Malo Hudo 8a 1295 Ivancna Gorica, Slovenia
declares that the following products:
Product name: Controller TNG Trade Name: Akrapovic Type or model: P-AE100
is in conformity with the requirements of the following Directives of the European Union: Regulation UN/ECE-R10 rev6
10R -06 1323
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
You can view your product’s FCC Declaration of Conformity (DoC) to the FCC 47
CFR Part 15, SubpartB, at:
http://www.akrapovic.com/docs/ControllerTNG/FCCCertification.pdf.
96 / 100
European Union Directives Conformance Statement Akrapovic d.d. hereby declares
that this Akrapovic Controller TNG P-AE100 is in compliance
with the essential requirements and other relevant provisions of Directive
2014/30/EU. You can view your product’s Declaration of Conformity (DoC) to
Directive 2014/30/EU (to EMC
Directive) at:
http://www.akrapovic.com/docs/ControllerTNG/CECertification.pdf.
97 / 100
www.akrapovic.com
DECLARATION OF CONFORMITY
COMPANY: ADDRESS:
Atlan d.o.o. Sveti Anton, Hrib 9 6276 Pobegi, Slovenia
declares that the following products:
Product name: Communication Detector Trade Name: Atlan Type or model: VTS CAN SNIFFER
is in conformity with the requirements of the following Directives of the European Union: Regulation UN/ECE-R10 rev5
E26 10 R – 05 1141
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
You can view your product’s FCC Declaration of Conformity (DoC) to the FCC 47
CFR Part 15, SubpartB, at
http://www.akrapovic.com/docs/CanSniffer/FCCCertification.pdf.
98 / 100
Industry Canada compliance statement This Class B digital apparatus complies
with Canadian ICES-003. This device complies
with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada. Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
European Union Directives Conformance Statement Atlan d.o.o. hereby declares
that this Atlan Communication Detector VTS Can Sniffer is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/30/EU. You can view your product’s Declaration of Conformity
(DoC) to Directive 2014/30/EU (to EMC Directive) at:
http://www.akrapovic.com/docs/CanSniffer/CECertification.pdf.
99 / 100
www.akrapovic.com
509523
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>