IKEA Silverglans LED Driver Instruction Manual

IKEA Silverglans LED Driver

INSTRUCTION MANUAL

HOW TO STEER YOUR LIGHTING

When the driver is connected to the mains, it is possible to turn ON/OFF all products connected to the driver, but if you want to dim or connect your products to IKEA Smart lighting products, you need to buy a separate steering device (e.g. a remote control).

The steering device needs to be paired with your driver/s. If you have more than one (1) driver you can pair each one with the steering device, so that the entire combination can be turned ON/OFF or dimmed at the same time.

PAIRING A STEERING DEVICE TO YOUR DRIVER

1. Connect at least one (1) product to the driver before you begin the pairing. Make sure that the mains power is turned ON.
2. Locate the pairing symbol on the driver. Hold the steering device close to the pairing symbol (no more than 5 cm away).
3. Press and hold the pairing button on the steering device for at least 10 seconds. A red light will shine steadily on the steering device.

The product connected to the driver will begin to dim and flash one time to indicate that the driver is being paired to the steering device.

HOW TO FACTORY RESET YOUR DRIVER

If the driver does not respond or if you want to un-pair the driver from a steering device you might have to make a factory reset. The driver is forced to factory reset by carefully push and hold the small button (marked RESET) with a tip of pen on the driver enclosure and applying a slight pressure. A factory reset can also be done by toggle the main switch 6 times.

MPORTANT!

• The driver is for indoor use only and can be used in temperatures ranging from 5ºC to 45 ºC.
• Do not leave the driver in direct sunlight or near any heat source, as it may overheat.
• The declared radio range between the driver and the steering device is measured in open air. Different building materials and placement of the units can affect the wireless connectivity range.

CARE INSTRUCTIONS

To clean the driver, wipe with a dry soft cloth. Never use abrasive cleaners or chemical solvents as this can damage the product.

PRODUCT SERVICING

Do not attempt to repair this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks.

TECHNICAL DATA

• Type: ICPSLC24-30-IL44-1
• Input: 100-120 VAC, 50/60 Hz, 0.51 A
• Output: 24.0V DC
• Max total load: 1.25 A, 30.0 W
• Radio range: 10 m in open air.
• Operating frequency: 2405-2480 MHz
• Output power (EIRP): 9.5 dBm
• IP-class: IP44

Indoor use only

• Manufacturer: IKEA of Sweden AB
• Address: Box 702, SE-343 81 Älmhult, SWEDEN

The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.

Product Usage Instructions:

Pairing a Steering Device to Your Driver:

1. Connect at least one (1) product to the driver with mains power turned ON.
2. Locate the pairing symbol on the driver and hold the steering device close to it (within 5 cm).
3. Press and hold the pairing button on the steering device for at least 10 seconds until a red light shines steadily. The product connected to the driver will indicate pairing by dimming and flashing once.

Care Instructions:

To clean the driver, wipe it with a dry soft cloth. Avoid abrasive cleaners or chemical solvents to prevent damage.

Product Servicing:

Do not attempt to repair the product yourself as it may expose you to dangerous voltage points. Seek professional servicing if needed.

How to Factory Reset Your Driver:

If the driver is unresponsive or needs to be unpaired, perform a factory reset by either pressing and holding the RESET button with a pen tip or toggling the main switch 6 times.

FAQ:

What should I do if my driver is not responding?

If the driver is unresponsive, try performing a factory reset as described in the manual.

Can I repair the product myself?

No, it is advised not to attempt repairing the product yourself due to potential risks. Seek professional help for servicing.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>