HELLA 7040 Cassette Awning CLEO Instruction Manual
- June 3, 2024
- HELLA
Table of Contents
7040 Cassette Awning CLEO
Installation Instructions and Instructions for Use These instructions must be
read prior to installation and use!
Cassette awning CLEO 7040 Operating guidelines
Installation Instructions and Instructions for Use
Table of Contents
Preliminary remarks HELLA Cassette awning CLEO 7040 …………………………………………..3
General notes………………………………………………………………………………………………………..4 CE
marking……………………………………………………………………………………………………………5 Safety instructions
………………………………………………………………………………………………….6 Designated use
……………………………………………………………………………………………………10 Servicing, maintenance and repair
………………………………………………………………………….11 Operating
guidelines……………………………………………………………………………………………..14 Before installation
…………………………………………………………………………………………………16 Overview cassette awning CLEO 7040
……………………………………………………………………17 Overview tensioning bracket types
………………………………………………………………………….18 Installation of wall / ceiling
brackets…………………………………………………………………………20 Rafter bracket installation
………………………………………………………………………………………22 Installation on
concrete………………………………………………………………………………………….23 Installation on brickwork
………………………………………………………………………………………..26 Installation on
wood………………………………………………………………………………………………28 Installation on concrete ceiling
face, installation set 9 ………………………………………………..30 Further installation
situations, installation set 9 …………………………………………………………33 Installation of the
awning ……………………………………………………………………………………….34 Adjusting the awning
…………………………………………………………………………………………….37 Electric commissioning and overview
table power …………………………………………………….43 Activation guidelines for electric
drives…………………………………………………………………….45 Wiring diagram for motors with switch
operation ……………………………………………………….46 Wiring diagram for motors with Somfy io
………………………………………………………………….46 Wiring diagram for motors with elero radio
……………………………………………………………….47 Wiring diagram for motors with ONYX.NODE
…………………………………………………………..48 Wiring diagram for motors with
ONYX.CONNECTOR………………………………………………..48 Overview LED lighting with remote control
……………………………………………………………….50 Replacing a folding arm with integrated LED
lighting …………………………………………………51 Technical data
……………………………………………………………………………………………………..54 Configuration
……………………………………………………………………………………………………….55
Operation……………………………………………………………………………………………………………. 56 Operating
guidelines……………………………………………………………………………………………..57 Ideal use of the radio
signal……………………………………………………………………………………57 Fault
removal……………………………………………………………………………………………………….58
Disposal……………………………………………………………………………………………………………… 58 Commissioning/functional
check …………………………………………………………………………….65 Removal and
Disposal…………………………………………………………………………………………..66 Handing over report (for the
fitter) …………………………………………………………………………..67 Handing over report (for the user)
…………………………………………………………………………..68
Installation Instructions and Instructions for Use
Preliminary remarks HELLA Cassette awning CLEO 7040
With this HELLA product you have opted for a high-quality product with a most
up-to-date technology that can nevertheless be easily installed and operated.
In these instructions we describe the basic installation, commissioning and
use.
For authorized specialist staff For the consumer (user)
The following symbols will assist you with the installation or use and require
a safetyconscious conduct:
Attention! This symbol indicates instructions that, if disregarded, can put
the user in danger. Attention! This symbol indicates instructions that, if
disregarded, can potentially result in damage to the product. This symbol
indicates instructions for use or helpful information.
This symbol requires you to act.
Attention! This symbol indicates a risk of injury or danger to life due to an
electric shock.
This symbol indicates parts of the product, for which you will find important
information in these installation instructions.
Installation Instructions and Instructions for Use
General notes
Questions In case of questions concerning the installation or the use of your
product, please consult your authorized specialist shop.
Spare parts/repairs Spare parts are available at your HELLA specialist shop.
Only spare parts that are approved by HELLA are allowed to be used.
Warranty/guarantee Precondition for warranty and guarantee is a correct and
regular maintenance of the sun protection device (at least once a year).
Warranty claims are subject to statutory limitation periods. Service parts are
excluded from the warranty; the same applies for changes in colour and changes
in characteristics caused by UV radiation.
Liability In case of non-observance of the directions and information given in
these instructions and in case of improper operation or unintended use, the
manufacturer shall not accept any warranty claims concerning any damage to the
product. In these cases, the liability for consequential damage to any parts
or persons is ruled out as well.
Legal notes The graphs and texts of these instructions were carefully
prepared. We cannot be held liable for any errors and their potential
consequences! Subject to technical modifications to the product and to these
instructions! These instructions include copyrighted information. All rights
reserved! The listed product or brand names are trademarks of the respective
owners.
Subject to technical modifications Date of Issue April/2022
3
4
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
CE marking
The HELLA cassette awning CLEO 7040 is in compliance with the declaration of
performance according to the Construction Products Regulation; if the unit is
operated with a motor drive it is additionally in compliance with the
Machinery Directive and the Guideline for Electromagnetic Compatibility; in
case of proper use, the awning corresponds to the basic requirements of the
harmonised standard EN 13561. The respective declarations are deposited with
the manufacturers.
HELLA Sonnen- und Wetterschutztechnik GmbH A-9913 Abfaltersbach, Nr. 125 16 LE-GGAM-01-001 EN 13561:2004+A1:2008 Cassette awning CLEO 7040 Exterior textile sun protection Wind resistance: class 2
All awnings are suitable up to wind force 5 (7.5-10.4 m/s) according to
Beaufort and correspond to wind protection class 2 according to EN13561 upon
delivery. Exceptions and specifications regarding the wind resistance of the
installed awning are given in the respective product documentations. When
installed, the awning only fulfils the requirements of the given wind
protection class according to DIN EN 13561 only if:
the awning is installed with the recommended type and number of brackets.
during installation the information and instructions given in these
instructions as well as the information and instructions of the manufacturers
of the screws / dowels have been observed,
the product is installed with the recommended type and number of fasteners /
screws.
No changes, rebuildings or extensions, with the exception of those described in these instructions, are allowed with this product. The fixed CE-label expires with any change, rebuilding or extension.
Subject to technical modifications Date of Issue April/2022
5
Installation Instructions and Instructions for Use
Safety instructions
These installation instructions refer to prefabricated elements, that (1) for
100% are made from parts, which are defined by us, and (2) which are made in
manufacturing processes, which are defined by us too; in all other cases we do
not provide any guarantee! The safety instructions as well as the appropriate
instructions must be read carefully before installation and use. In case of
non-observance of the directions and information given in these instructions
and in case of improper installation and operation or unintended use, the
manufacturer shall not accept any warranty claims concerning any damage to the
product. In these cases, the liability for consequential damage to any parts
or persons is ruled out as well.
– Follow the described installation steps and pay attention to recommendations
and notes.
– Keep these instructions in a safe place. – All installation and removal
works, as well as maintenance and repair
works are only allowed to be carried out by authorised and qualified
specialist staff. – If switching, automatic or radio control devices are used
to operate the units, the information given in the enclosed instructions of
the manufacturer must be observed. – During operation do not put your hand
into or touch movable parts. – Ensure that clothing or body parts cannot get
caught on the unit. – Observe the regulations for prevention of accidents of
the employer’s liability insurance association! – Before operation check the
unit for visible damage. If the unit is damaged, it should not be used; please
consult authorized specialist staff immediately. – Risk of injury and accident
due to the weight of the product! – Take safety measures against the danger of
squashing, especially when operating the unit with automatic devices. – Place
the operating switch within sight of the unit, but not near any of the moving
parts. – Never let children play with the unit.
A sun protection device with electric drive cannot be retracted without
current. We therefore recommend the use of an emergency power generating unit
or a motor with an emergency crank handle, especially in regions with frequent
power failures.
Danger of suffocation!
Ensure that the foil cannot get into the hands of children. Keep the foil in a
safe place.
6
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Safety instructions
Attention! Risk of injury or danger to life due to an electric shock!
– Set-up, examination, commissioning and error correction of the unit must
only be performed by authorised or trained expert staff (as per VDE 0100).
– Switch off the current to the connecting lines when working at the unit.
There is danger to life! Take safety precautions against unintentional
switching on!
– Check the electrical wires regularly for damage. Do not use the unit if any
damage is found.
– Our electrically driven units are in accordance with the regulations for
power plants acc. to VDE 0100. We cannot guarantee for the operational
reliability of the unit with non-approved modifications.
– The enclosed installation instructions of the electrical devices supplied
must be observed.
Units with motor drive: The drives used are operated with a voltage of AC
230V/50Hz. Please check the power supply provided by your utility company
before connecting. Any other voltage can destroy the drives.
Danger of squashing To avoid at the best the danger of squashing in the area
of movable parts, such as roller tube, cassette, folding arms, front rail
etc., especially when automatic devices are used or when the unit is for
example operated automatically by a wind controller or rain sensor, it is
mandatory that the awning is installed in a height of at least 2,5 m or above,
measured from the floor or a permanent access way. Hereby it must be observed,
that a distance of at least 0.40 m between the front rail and a fixed object
is ensured, if the front rail, due to the inclination of the awning, goes
below a height of 2.5 m, measured from the floor or a permanent access way. If
such an installation is due to the local situation not possible , the client
has to take appropriate safety measures, such as a cover or placing the
operating switch (touch contact switch) within sight of the awning.
Installation Instructions and Instructions for Use
Safety instructions
If it is necessary to lift the awning via ropes at a higher altitude, the
awning must – be removed out of the packaging. – be tied to the pull ropes in
such a way, that a slipping out of the awning
is prevented, – lifted evenly in a horizontal position. The same applies for
the removal of the awning. It is not allowed that climbing aids are leaned
against or fixed to the awning. They must have a stable base and provide a
firm support. Only use climbing aids with an appropriate carrying capacity.
When working at higher heights, there is risk of falling. Please make sure
that suitable fall protection devices are used.
Awnings are only allowed to be used for the purpose specified in the
instructions for use. Changes, such as extensions or rebuildings, that are not
provided by the manufacturer, are only allowed to be carried out with the
manufacturer’s written approval.
Additional loadings such as objects that are sticked to the awning or cable
tensionings can damage the awning or lead to its crashing, and are therefore
not allowed.
Subject to technical modifications Date of Issue April/2022
7
8
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Safety instructions
Winter operation: Snow or ice can destroy the unit. The unit may only be
operated, if no ice or snow is lying on the cover. During this time automatic
control devices must be switched to manual operation.
To prevent damage, please retract your sun protection device with rain,
snowfall or wind. If automatic control devices are used, adjust the wind
controller analogously to the installed wind resistance class of your sun
protection device. Wind resistance class 0 = wind force <4 (Beaufort), a
performance not required or not measured (according to DIN 13561) or a
product, that does not comply with the requirements of the wind resistance
class 1. Wind resistance class 1 = wind force 4 (Beaufort), moderate breeze,
moderate wind, moves twigs and thin branches, whirls up dust and loose paper
Velocity 20 27 km/h = 5.5 7.4 m/s Wind resistance class 2 = wind force 5
(Beaufort), fresh breeze, fresh wind. Smaller deciduous trees start to sway,
white crests are formed on lakes. Velocity 28 37 km/h = 7.5 10.4 m/s
Installation Instructions and Instructions for Use
Designated use
Sun protection Thermal protection Sight screen Anti-glare blind
Rain protection (only partly!) The inclination of the awning in the drawn-out
position must be at least 14° to prevent water pockets when it is raining.
Also with a sufficient inclination, a complete denseness of the seams cannot
be guaranteed when it is raining!
Subject to technical modifications Date of Issue April/2022
9
10
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Servicing, maintenance and repair
With the purchase of your awning you have opted for a high-quality product. To
enjoy your awning for as long as possible, please observe the following
information: Notes to awning covers made of brand acrylic fibres Brand acrylic
fibres, as used for awnings, are materials of the highest quality for awnings.
As they are dope-dyed, these materials show the highest light- and colour-
fastness. In addition, their resistance to tearing and resistance to weather,
rotting and environmental effects is unsurpassed. Furthermore, a special
textile finishing makes them dirt-, water-, oil- and grease resistant. The
awning cover is heavily tested. At the weaving plant, at the awning
manufacturer and during awning fabrication. As with other covers, differences
in the surface uniformity can also occur with the awning cover. When viewing
from the top or seeing through, you will perhaps find small knots, spots of
colour, irregular runs of threads or minimal differences and displacements in
the design and rapport, as well as differences in the colour. Please note,
that the awning will cause a different colour effect in sunlight and in shade.
Naturally, the optical colour perception depends on the composition and the
intensity of the emerging light. With increasing depth of colour, more light
will be absorbed and less will be reflected. Therefore dark coloured covers
let through a small amount of light, while light colours let a lot of light
through. Due to the part-absorption, the composition of the light shining
through will be modified, which results in other colour perceptions. Due to
the coloured pigments embedded in the cover and the impregnation, shadings
caused by crinkles or crumple folds can appear, that, especially with light
colours, become visible as strips of shade. The function, strength or density
of the cover will not be reduced by that. Minor differences in colours between
the different cover strips or differences in colours with regard to the
collection of samples cannot be ruled out. The fabrication of several strips
also with varying widths depends on the overall width of the awning. Ripples
in the cover and wrinkling at the seams can arise, because the cover is double
rolled up at the seams. The highest strain is on the seams of the cover. When
rolling up the cover, the seams and hems lie on top of each other,
intensifying the strain. Hems and seams will be pressed flat, increasing in
length. As a result, the lateral seams of the cover can hang down slightly.
Sagging as a result of the own weight of the cover is possible. These
specified phenomenons are not faults in the awning cover, which have been
overseen in the testing; they are unavoidable due to technical, material and
physical regularities. They therefore do not entitle the customer to any
refusal or reduction of the purchase price. Correspondingly, the guidelines
for the assessment of ready-made awning covers, summarized by the German
Federal Association “Manufacture of technical textile registered association”
(Bundesverband Konfektion Technischer Textilien e. V.), are also an integral
part of our conditions of sale and delivery.
Installation Instructions and Instructions for Use
Servicing, maintenance and repair
Cleaning
Cleaning As a sun protection device fixed outside, the unit can get dirty in
the course of time. This will not reduce the usability of your unit. The
powder-coated parts of your unit will remain presentable for longer, if they
are cleaned regularly with a soft woollen cloth.
Do not use solvents, alcohol (rubbing alcohol) or scouring cleansing agents!
Leaves or other foreign material lying on the awning cover and in the awning
cassette must be removed immediately. There is danger of damage or crashing to
the awning.
Preventive measures If you have to draw in the cover in a wet condition,
please draw it out for drying when the next opportunity arises, to prevent
marks caused by mould or mildew.
Subject to technical modifications Date of Issue April/2022
11
12
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Servicing, maintenance and repair
Maintenance
Maintenance
All inspection and maintenance works must be carried out by a specialised
company from HELLA or a HELLA partner. Regularly check the electrical wires of
motor driven units for damage. Check the mechanical parts of your unit for
visible damage. After exceptional events such as storm, hail, sleet,
maloperation or the like, the unit must be checked for noticeable damage prior
to operating it. If the unit is damaged, it must not be used; consult
authorized specialist staff immediately. It is recommended to have the unit
maintained by specialist staff on an annual basis. This way wear is detected
at an early stage and damage to the unit is prevented.
Repair works
Repair works
Improper repair works may cause both risk of injury to persons or damage to
the units. All repair works must be carried out by a specialised company from
HELLA or a HELLA partner. Use original HELLA spare parts only.
Installation Instructions and Instructions for Use
Operating guidelines
3 1 2
3
Legend Crank handle hook Crank rod Eyelet
Model with crank handle drive Stick the crank handle hook together with the
crank rod into the eyelet.
The awning is extended or retracted by turning the crank rod.
The respective direction of rotation depends on the drive side.
In the direction of extending the stop position of the gear is limited by an
override. In this position you hear a click, when turning the crank handle
beyond this stop.
Do not use force when turning towards the upper stop.
Subject to technical modifications Date of Issue April/2022
13
14
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Operating guidelines
Motor drive
The awning can be extended or retracted by activating a switch, a hand-held
radio transmitter or an automatic device.
The end points of the drive are adjusted ex works. Please observe the enclosed
instructions of the manufacturer of the drive, if any modification is
required.
Lighting
By activating a radio transmitter or an automatic device the lighting is
switched on or off or dimmed. You will find detailed information in the
enclosed instructions of the manufacturer.
Hand-held radio transmitter with scroll wheel
Setting the scroll wheel function with hand-held radio transmitter “Somfy
Situo 5 Variation A/M io”:
– Open the rear housing cover – Set the selector switch for the operating mode
“E” to position 2 In this way the scroll wheel reacts to the LED lighting and
heating. You will find detailed information in the enclosed instructions of
the manufacturer.
2
E
Installation Instructions and Instructions for Use
Before installation
Check the product immediately for possible shipping damage and for compliance
with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be used
complies with the given conditions to guarantee proper installation. In case
of doubt, please seek advice from a specialist enterprise for fixing
techniques. The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil. Carry
larger units by two persons. Transport and store the units carefully to
prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful not to
damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution! A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please make
sure that the ascent supports stand solidly and provide a firm grip.
Subject to technical modifications Date of Issue April/2022
15
16
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Overview cassette awning CLEO 7040
1 2
5
876 4
3
Legend End cap Front rail Folding arm Brackets Swivel arm bearing Cassette
profiles Supporting bearing (acc. to design) LED control unit (acc. to design)
Installation Instructions and Instructions for Use
Overview tensioning bracket types
2 1
3 4
Subject to technical modifications Date of Issue April/2022
17
Legend Wall bracket type B (03630505) Wall bracket type C (03630506) Wall bracket type D (03630507) Rafter bracket type K (03630515)
18
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Overview tensioning bracket types
1
2
3
4
Legend Ceiling bracket type E (03630511) Ceiling bracket type F (03630512) Ceiling bracket type G (03630513) Ceiling bracket type H (03630514)
Subject to technical modifications Date of Issue April/2022
19
Installation Instructions and Instructions for Use
Installation of wall / ceiling brackets
You specified the number, form and type of brackets on purchasing the awning
in accordance with the size, the mounting base, the screw pull-out forces, the
mounting material and the wind resistance classes. Recommendations can be
found in our awnings price list and the product-related calculation tables.
Before starting the installation, please check whether the details you gave in
your order concerning the mounting base comply with the given mounting base.
In case of doubt, please obtain information from a specialist shop or a
structural engineer.
If there are any discrepancies that could jeopardise the safety, the
installation must not be carried out. The wind class given may need to be
reduced.
Mark the position of the brackets (2) correspondingly: – Determine the
position for the holes of the fastening screws
(measure, adjust, mark). – Drill holes, align and affix brackets. Please
observe the maximum allowable offset (± cm) – Check the alignment of the
brackets by means of a level or a plumb
line. The brackets must be situated on one level both horizontally and
vertically! Irregularities in the mounting base must be equalised accordingly.
– Observe the torque indications of the anchor manufacturer when tightening
the screws. Please note, that the bore hole geometry is decisive for the load-
bearing capacity of an anchor. – All elongated holes defined in the bracket
must be used for fastening.
2 1
Legend
Distance between the tensioning brackets
Bracket (type B)
20
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation of wall / ceiling brackets
Check the mounting base and determine the appropriate mounting material taking
into account the mounting base and the fixing devices. Information on the
pull-out forces can be found in the documents in force. Fix the brackets to
the mounting base in accordance with the working guidelines.
1
Wall installation
3 2 4
1 4
2 3
Ceiling installation
Legend Brackets Plain washer Nut Fastening Devices
Subject to technical modifications Date of Issue April/2022
21
Installation Instructions and Instructions for Use
Rafter bracket installation
Check the rafters (1) for their material condition or for sufficient
stability. Align the rafter holder (2) and fix it to the rafter. Based on the
holes of the rafter holder, create the relevant through holes (3) and attach
the holder. Check if the holding device fits well. Connect the rafter holder
and the ceiling bracket (4) by means of the enclosed threaded screws and nuts
and align them.
The brackets must be situated on one level both horizontally and vertically.
It may be necessary to level out irregularities on the mounting base.
6
5
3 2 4
1
7
Legend Rafter Rafter holding device Mounting holes Ceiling bracket
Plain washer Nut Fixing material
22
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation on concrete
1
23
7
4
Installation of the anchor bolts as per approval ETA-05/0069: – Drilled hole
preparation ø12 mm
Installation of the attachment: – Tightening torque as per ETA-
05/0069
6 5
Legend Concrete Installation set 1; anchor bolt FAZ II M12 Bracket Minimum anchoring depth – 70 mm
Installation Instructions and Instructions for Use
Installation on concrete up to 60 mm ETICS
1
23
7
4
6 5
Installation of the anchor rod as per approval ETA-12/0258:
– Drilled hole preparation ø14 mm – Observe the anchoring depth and
the minimum edge distance! – Drilled hole cleaning – Fill drilled hole with
mortar FIS SB – Slide the anchoring element into
the drilled hole – Wait for the curing time
Installation of the attachment:
– Cut free lock nut in the ETICS – Align lock nuts
(1 mm before the plaster level) and then seal the expansion joint – Cut the
threaded rod to the correct length – Screw down the bracket
Legend Concrete
Installation set 8; anchor rod M12
ETICS Bracket
Thickness of the non-bearing layer <60 mm
Anchoring depth 140 mm = drilled hole depth
Lock nut + washer
Subject to technical modifications Date of Issue April/2022
23
24
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation on concrete 60-200 mm ETICS
1 23 4
6 5
Installation of the anchor rod as per approval ETA-02/0024: – Drilled hole
preparation ø18 mm – Observe the anchoring depth and
the minimum edge distance! – Drilled hole cleaning – Fill drilled hole with
mortar FIS V – Slide the anchoring element into
the drilled hole – Wait for the curing time
Installation of the Thermax as per approval Z-21.8-1837: – Mill open the
thermal insulation
prior to injection – Sealing of the expansion joint
Installation of the attachment:
– Tightening torque as per Z-21.81837
– Sealing of the free elongated hole parts
Legend
Concrete
Installation set 3; Thermax 16/170 M12 ETICS
Bracket
Thickness of the non-bearing layer up to 200 mm Anchoring depth 140 mm =
drilled hole depth
Depending on the thickness of the non-bearing layer, different brackets must be used (60-170 mm; 170-200 mm).
Installation Instructions and Instructions for Use
Installation on brickwork
1 2 3
4
Installation of the anchor rod as per approval ETA-10/0383: Depending on the
type of stone, the injection anchor sleeve must be used!
– Drilled hole preparation ø12 mm without sleeve ø16 mm with sleeve (16×130)
– Drilled hole cleaning – Fill drilled hole (anchor sleeve) with
mortar FIS V – Slide the anchoring element into
the drilled hole – Wait for the curing time
Installation of the attachment:
– Tightening torque as per ETA10/0383
Legend Brickwork Installation set 2; anchor rod M10 Bracket Anchoring depth 130 mm drilled hole depth
Subject to technical modifications Date of Issue April/2022
25
26
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation on brickwork 60-170 mm ETICS
1 23
4
6 5
Installation of the anchor rod as per approval ETA-10/0383: Depending on the
type of stone, the injection anchor sleeve must be used!
– Drilled hole preparation ø18 mm without sleeve ø20 mm with sleeve (20×200)
– Drilled hole cleaning – Fill drilled hole (anchor sleeve) with
mortar FIS V – Slide the anchoring element into
the drilled hole – Wait for the curing time
Installation of the Thermax as per approval Z-21.8-1837: – Mill open the
thermal insulation
prior to injection – Sealing of the expansion joint
Installation of the attachment:
– Tightening torque as per Z-21.81837
– Sealing of the free elongated hole parts
Legend
Brickwork
Installation set 3; Thermax 16/170 M12 ETICS
Bracket
Thickness of the non-bearing layer up to 170 mm Anchoring depth 200 mm =
drilled hole depth
Installation Instructions and Instructions for Use
Installation on wood
1
2
3
Installation of the attachment:
– Drilled hole preparation ø9 mm – Secure bracket with wood screw
and washer
Legend
Wood
Installation set 5; wood screw ø12×120
4
Bracket
Drilled hole depth 125 mm
No wind protection class can be given with installation on wood due to the variance of the building material.
Subject to technical modifications Date of Issue April/2022
27
28
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation on wood 60-170 mm ETICS
1 23
4
6 5
Installation of the anchor rods: – Drilled hole preparation ø14 mm – Observe
the anchoring depth and
the minimum edge distance of 100 mm! – Drilled hole cleaning – Lubricate
threaded rod – Screw threaded rod into the wood
Installation of the Thermax following approval Z-21.8-1837: – Milling open the
thermal insulation – Sealing of the expansion joint
Installation of the attachment: – Sealing of the free elongated hole
parts
Legend
Wood
Installation set 3; Thermax 16/170 M12 ETICS
Bracket
Thickness of the non-bearing layer up to 170 mm Anchoring depth 140 mm =
drilled hole depth
Required wood quality is C24, P30, GL24, F40/30 or equivalent with a wood moisture of 15%.
Installation Instructions and Instructions for Use
Installation on concrete ceiling face, installation set 9
1
3
2
Register constructional situation:
– Thickness of the concrete ceiling – Determination of the theoretical
position of the concrete ceiling (consider differences is in the ground) –
Determination of the non-bearing layer ETICS (adhesive, insulation, plaster)
180
Legend
4
4
Brickwork
Concrete ceiling
5
ETICS
Ceiling position
Thickness of the non-bearing layer
Exclude the shape of the wooden spacer under consideration of the edge
distances The wooden spacers should rigidly be seated in the insulation.
Using a “multi-cutter” tool is recommended for cutting out the insulation.
Subject to technical modifications Date of Issue April/2022
29
The two lower drilled holes of the bracket should be preferred for installation. The third drilled hole serves for refitting potential errors (e.g. wrong assessment of the constructional situation or position of the concrete ceiling).
30
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation on concrete ceiling face, installation set 9
min. 55
min. 55
1 min. 140
Installation of the anchor rod as per approval ETA-12/0258: – Drilled hole
preparation – Observe the anchoring depth and
the minimum edge distance! – Drilled hole cleaning – Fill drilled hole with
mortar – Slide the anchoring element into
the drilled hole – Wait for the curing time
Legend
Anchor rod FIS A
Insert wooden spacers and
completely seal the last wooden
spacer towards the ETICS outer
1
surface.
(Fischer multi-adhesive and sealant)
3
The 5 mm spacers must not be used
as the last spacer. Then the anchor
2
rods can be cut to length.
Legend Wood distances Last wooden spacer Sealing joint all around
The last wooden spacer must always protrude 2-5 mm from the WDSV. A 5 mm thick wooden spacer per installation set is included as a reserve.
Subject to technical modifications Date of Issue April/2022
31
Installation Instructions and Instructions for Use
Installation on concrete ceiling face, installation set 9
2
1
Affix the bitumen band on the back of the wall bracket type I:
Affix two strips of bitumen band on the back of the wall bracket type I: Affix
them so that all holes are completely covered.
Legend Wall bracket type I Bitumen band
Fixing of the bracket:
Attach the wall bracket type I; while
doing so, push the anchor rod through
the bitumen band. Position washer
and nut and tighten them. The bracket
must be sealed all around again by
3
means of a joint between ETICS
1
surface and bracket (Fischer multi-
adhesive and sealant).
Legend Wall bracket type I Bitumen band Sealing joint all around
The sealing joints are maintenance joints that must be checked and maintained at regular intervals in order to prevent consequential damage.
32
Subject to technical modifications Date of Issue April/2022
190
258
Installation Instructions and Instructions for Use
Further installation situations, installation set 9
Constructional situation pressure-resistant installation on concrete With this
application, the wall bracket type I must be ordered and installed in
combination with the mounting set 2.
Installation Instructions and Instructions for Use
Installation of the awning
Wall installation
12
Ceiling installation
12
Rafter installation
3
3
197
258
Subject to technical modifications Date of Issue April/2022
33
308
318
318
Legend Wall / ceiling bracket Swivelling bracket Clamping screw with screw locking device
Swivel the awning into the bracket as shown and fix by means of the clamping
screws immediately.
The articulated arms are under high mechanical stress. The cover prevents a
discharge of this potential energy. There is danger to life. Attention! It is
not allowed to extend the awning before the clamping screw (3) has been fixed.
There is a high risk of injury and danger to life!
34
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Installation of the awning
1
2
3
Installation Instructions and Instructions for Use
Installation of the awning
Installation in recess
4
50
1
50
Legend Ordering width
Legend Wall / ceiling bracket Swivelling bracket unit Bracket positioning
stickers (Art.-Nr. 032203) Bracket centre
The swivelling bracket is delivered together with the arm bearing in the
middle. Its position is designated by a sticker. In exceptional cases (i.e.
bracket installation mistakes), the permissible deviation between the bracket
position and the arm bearing position is +/-50 mm.
Subject to technical modifications Date of Issue April/2022
35
36
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Adjusting the awning
Inclination adjustment with standard arm bearing
Maximum inclination adjustment with wall and ceiling installation from 5° to approx. 40°.
Wall installation Inclination adjustment 5°
Wall installation Inclination adjustment 40°
Ceiling installation Inclination adjustment 5°
Ceiling installation Inclination adjustment 40°
Installation Instructions and Instructions for Use
Adjusting the awning
Inclination adjustment with standard arm bearing
To adjust the angle of inclination, the cassette awning CLEO 7040 is equipped
with an adjusting mechanism, which enables an inclination from approx. 5° to
40° . Due to the special construction of the swivelling bracket, the
inclination of this awning model is adjusted by rotating the entire casing.
The angle of inclination and the horizontal position of the front profile are
adjusted ex works. If a modification is required, please proceed as described
in the following:
Completely extend the awning.
Put an Allen key 6 mm (5) onto the adjusting spindle (4). The casing of the
awning raises or lowers by turning the key (see the figure on the following
page). The respective arm can be adjusted easier if a second person slightly
lifts up the front rail (6). Proceed analogously with the second adjusting
mechanism. The awning raises or lowers side by side.
Ensure that the angle of the folding arms to one another is not more than 5°
during the adjustment procedure. Thus the adjustment procedure is to be
repeated several times on the left and right of the adjustment spindles until
the desired inclination is reached. Never turn against greater resistance.
Check the correct adjustment on the front rail by means of a spirit level in
the extended condition.
Subject to technical modifications Date of Issue April/2022
37
38
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Adjusting the awning
Inclination adjustment with standard arm bearing
2
3
6
1
Legend Wall bracket Casing awning Swivel arm bearing
4 5
Adjusting spindle Allen key SW 6 Support at the front rail
Subject to technical modifications Date of Issue April/2022
39
Installation Instructions and Instructions for Use
Adjusting the awning
Arm adjustment
Ex works your awning is optimally adjusted. To ensure a correct closing of the
awning, the folding arms (1) should be in a parallel position to the front
rail (2). The arm bearing bolt is mounted in an eccentric bush (6). You can
adjust the folding arms at any time as follows:
In order to correct the angle, you must open the clamping screw for the
eccentric bush (4) by means of an Allen key 2.5 mm (5) first. In order to
access the threaded pin, you must extend the awning (see illustration on the
next page).
Then retract the awning to approx. 0.5 m and correct the position of the arm
by turning the eccentric bush (6) by means of an Allen key 8 mm (7).
Please note: The position mark (9) of the eccentric bush must be within the
indicated adjustment range (10). Otherwise the parallelism of the arm to the
casing can be adjusted, however, the awning will still extend askew.
The arm should be parallel to the casing of the awning! For facilitated
adjustment, the arm can be supported by hand (8).
Check the adjustment of the inclination and, if necessary, repeat the
described procedure until the desired result has been reached.
Now the adjusting procedure of the swivel arm bearing (3) regarding the arms
is completed. The adjusting procedure on the right side must be performed
analogously.
Please note: Finally retighten the clamping screws (4)!
40
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Adjusting the awning
Arm adjustment
2
1 8
5
4
3
76
12 11
64 9 3
10
max.
11 min.
Legend Folding arm Front rail Swivel arm bearing Clamping screw for eccentric
bush
Allen key SW 2.5 Eccentric bush for arm adjustment
Allen key SW 8 Lifting the folding arm Position mark of the eccentric bush Adjustment range (opposite side in mirror image) Casing – awning View from the bottom
Subject to technical modifications Date of Issue April/2022
41
Installation Instructions and Instructions for Use
Adjusting the awning
Adjusting the end positions
41 2 3 1 2
Changing gear points with awnings with crank handle operation:
The end points of the crank handle gear can be adjusted. If the adjustment ex
works is to be changed, please proceed as follows:
Extend the awning until the stop position is reached (you hear a click).
Loosen the fixing screw (1) by means of an Allen key 3 mm (3).
Move the awning with the crank rod to the desired position. Tighten the fixing
screw (1).
Legend Fixing screw Gear (discreetly hidden) Allen key SW3 Adjustment hole
42
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Electric commissioning and overview table power
This general overview table shows which awning designs are possible with an electric control.
Awning drive LED lighting Heater
Possible types of operation
Somfy Somfy radio
cord-bound
io
ONYX
yes
yes
yes
no
yes
yes
no
no
no
Cord operation
no no yes
Installation Instructions and Instructions for Use
Electric commissioning and overview table power
Technical data of the awning Connection for all cables: 220-240V / 50-60Hz
Overview powers [W]
Subject to technical modifications Date of Issue April/2022
43
44
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Activation guidelines for electric drives
The motors we use are drives with integrated planetary gear, brakes, limit
stops at the top and at the bottom, and thermo cut-off switches, also not only
a motor, but a complete drive system.
In some respect, the drives do NOT correspond to other household electrical
consumers. Please strictly observe the following notes and safety
instructions.
The construction, checking, commissioning and error-correcting of the
electrical system are only allowed to be carried out by an electrician (acc.
to VDE 0100). In case of improper connection, considerable danger can arise
for the user.
– Follow the wiring diagram precisely! – We cannot accept responsibility for
damage, that can result from
improper installation. – Never simultaneously activate the drives with an
UPWARDS and a
DOWNWARDS signal! – Keep a break of approx. 0.5 seconds between the UPWARDS
and
the DOWNWARDS command (is often neglected with Instabus EIBsystems).
Radio interference suppression The drives are provided with a radio
interference suppression according to the current VDE standards and EC
Guidelines. If the drives are operated with other devices, that include
interferences, it is the fitter’s duty – as part of the obligation to suppress
interference – to ensure that the entire unit complies with the current
regulations.
Operation in wet spaces The drives are “splash-proof”; if they are operated in
wet spaces, the VDEguidelines, inter alia VDE 0100/Parts 701, 702, the
guidelines of the local electric supply companies and of the TÜV must be
observed and fulfilled.
Both the instructions and notes given in these instructions, as well as the
instructions and notes given in the respective enclosed instructions of the
manufacturers of the drive systems must be observed.
Subject to technical modifications Date of Issue April/2022
45
Installation Instructions and Instructions for Use
Wiring diagram for motors with switch operation
Drive system awning
2 1
1 N
M
2
4
1
3
PE
5
L1 N PE
3
Legend Drive system awning Hirschmann connector Junction box Switch Mains
For more details concerning the electrical connections, powers, operating
instructions and programming, please refer to the enclosed documents of the
manufacturer or the HELLA installation instructions.
It is essential that switches for the awning drive be electrically and
mechanically locked.
Wiring diagram for motors with Somfy io
Drive system awning
2 1
1 N
M
2
1
3
PE
4
L1 N PE
3
Legend Radio drive awning Hirschmann connector Junction box Mains
For more details concerning the electrical connections, powers, operating
instructions and programming, please refer to the enclosed documents of the
manufacturer or the HELLA installation instructions.
With the radio system Somfy io all receivers must be taught one after another
(order does not matter), i.e. do not connect several receivers to the network
at the same time as the radio system does not support a simultaneous teaching
process of multiple components.
46
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Wiring diagram for motors with elero radio
Drive system awning
2
1
1N
M
2
1
3
PE
4 L1 N PE
3
Radio drive awning Hirschmann connector Junction box Mains
For more details concerning the electrical connections, powers, operating instructions and programming, please refer to the enclosed documents of the manufacturer or the HELLA installation instructions.
Subject to technical modifications Date of Issue April/2022
47
Installation Instructions and Instructions for Use
Wiring diagram for motors with ONYX.NODE
Drive system awning
Typ YR 3×0,8
5
0,5
4
L1 N PE
3
Local Motor
2 1
1 N
M
2
1
3
PE
N+
6
Power NNL L
Legend Drive system awning Hirschmann connector Junction box Mains Button ONYX.NODE
For more details concerning the electrical connections, operating instructions
and programming, please refer to the enclosed documents “ONYX”.
It is essential that switches for the awning drive be electrically and
mechanically locked.
Wiring diagram for motors with ONYX.CONNECTOR
Drive system awning
2
1
22
33 M
1
1 1N
4 4PE
4
L N PE
3
5 N PE L
Legend Drive system awning Hirschmann connector Junction box Mains ONYX.CONNECTOR
For more details concerning the electrical connections, operating instructions
and programming, please refer to the enclosed documents “ONYX”.
It is essential that switches for the awning drive be electrically and
mechanically locked.
48
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Wiring diagram for motors with ONYX.CONNECTOR
Hirschmann
Hirschmann
STAK 3
STAS 3
1
3
2
PE
44 PE
11
N
N
22
L
L
1,5mm²
33
Hirschmann
Hirschmann
STAK 3
STAS 3
3
4
44 PE
11
N
ONYX.CONNECTOR
33
M
22
~
1,5mm²
Hirschmann
Hirschmann
STAK 3
STAS 3
1
3
2
PE
44 PE
11
N
N
22
L
L
1,5mm²
33
Hirschmann STAK 3
3
44 PE
11
N
ONYX.CONNECTOR
33
22
Hirschmann STAS 3
5
1,5mm²
Legend Junction box Adapter plug ONYX.CONNECTOR Hirschmann plug connection
Motor Lighting
For more details concerning the electrical connections, operating instructions and programming, please refer to the enclosed documents “ONYX”.
Installation Instructions and Instructions for Use
Overview LED lighting with remote control
2
1 3
Legend LED control unit* Connecting cable 230V Integrated LED lighting
Technical data
Light temperature Colour rendering index of the LED strips Control LED
Operating temperature (outside temperature) IP rating Cable
2700 K (warm-white) >90 Somfy io, ONYX (dimmable) -20°C to +45°C IP44 10 m with open end piece
- … The control of LED lighting is possible with Somfy io or ONYX The individual modules are described in the following.
Subject to technical modifications Date of Issue April/2022
49
50
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Schematic wiring diagram
3 8 4
8
8
7 8
5 9
6 9
7 10 8
11
1 L1 N PE
2
3
1N 2 3 PE
230V AC 24V DC
4
8
+-
5
–
6
++-
+-
7
9
L.E.D. L.E. D.
L. E. D.
L.E.D. L.E. D.
L. E. D.
8
10
8 11
Subject to technical modifications Date of Issue April/2022
51
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Schematic wiring diagram
Legend
Mains
Junction box
Hirschmann connector
Control module (Somfy io or
9
ONYX)
Power supply unit
LED receiver (Somfy io or ONYX
Connection point at the arm bearing
Two-wire line connector
Connection point at the centre hinge
LED in the upper arm
LED in the lower arm
Upper arm tube
Lower arm tube
8 13 12
13
8
52
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Control of the LED lighting with the control module ONYX
3
2
1
The configuration, commissioning and operation of the LED lighting with the
control module ONYX are described in more detail on the pages to follow.
Legend Power supply unit Control module ONYX Connection point
Installation Instructions and Instructions for Use
Technical data
LED control module for awning ONYX Input Output Power consumption in the
standby mode Maximum power consumption (depends on the size of the awning) IP
rating Permitted operating temperature range Radio frequency Transmission
power Installation type
Channels
200 240 VAC / 50-60 Hz 24 VDC PWM 0.5 W 90 W
IP 55 -20 °C to +55 °C 868.3 MHz 12.6 mW Already ex works mounted in the LED
awning from HELLA Sonnen- und Wetterschutztechnik 1
Subject to technical modifications Date of Issue April/2022
53
54
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Configuration
Once the connection cable of the ONYX.LED is supplied with voltage, the
lighting of the awning switches on briefly and then is dimmed slowly. In this
way you can ascertain, if the awning lighting is connected correctly. This
process is no longer performed, when ONYX.LED is already connected with a
hand-held radio transmitter ONYX.CLICK or with ONYX.CENTER.
Before configuring the ONYX.LED, download HELLA’s free app ONYX from the App
Store/Google Play to your smart phone.
Configuration ONYX.LED with ONYX.CLICK (without ONYX.CENTER) Before you can
use ONYX.LED in combination with the hand-held radio transmitter ONYX.CLICK,
ONYX.CLICK must be first connected with the ONYX app. Once the hand-held radio
transmitter is connected with the app, the menu item “Configure devices”opens.
You can now add a new awning lighting ONYX.LED with “+”. The camera opens. By
tapping on “” in the lower area of the screen, a window opens showing all
available devices. The overview displays ONYX.LED as “LED” . ONYX.LED is
connected with the hand-held radio transmitter via “Adaption to the system”.
Then follow the instructions on the screen. The configuration is continued as
described in the instructions for use for ONYX.CLICK.
Configuration of ONYX.LED with ONYX.CENTER Before you can use ONYX.LED in
combination with ONYX.CENTER, ONYX.CENTER must first be connected with the
ONYX app as described in the instructions for use. Once ONYX.CENTER is set
completely, the “Configuration mode” is activated. You find it under
“Settings”. Under the menu item devices a new awning lighting ONYX.LED can now
be added with “+”. The camera opens. By tapping on “” in the lower area of the
screen, a window opens showing all available devices. The overview displays
ONYX.LED as “LED” . ONYX.LED is connected with the hand-held radio transmitter
via “Adaption to the system”. Then follow the instructions on the screen. The
configuration is continued as described in the instructions for use for
ONYX.CENTER.
Installation Instructions and Instructions for Use
Operation
Operation via the hand-held radio transmitter ONYX.CLICK The lighting is
switched on and off with the two pushbuttons “UP” and “DOWN”. If one of the
two pushbuttons is pressed longer, the lighting can be dimmed. If this
pushbutton is released, the current brightness of the lighting is kept. The
current brightness is reset after the switching on.
Groups with different shading and light control devices can be configured
freely at the hand-held radio transmitter ONYX.CLICK. All elements in one
group can be controlled together.
Per group configured one brightness value can be saved at the hand-held radio
transmitter ONYX.CLICK, so that it can easily be assessed again at a later
time.
Operation via the ONYX app The awning lighting switches on or off by tapping
on the respective icon of the lighting. The current brightness is reset after
the switching on. By swiping up or down over the respective icon of the
lighting, the awning lighting is dimmed up to the maximum/minimum brightness.
Whilst the awning lighting is dimmed, the desired brightness can be kept by
briefly tapping.
Subject to technical modifications Date of Issue April/2022
55
56
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Operating guidelines
Groups In combination with ONYX.CENTER, groups with their different sun
protection systems/awning lightings can be configured freely in the ONYX app.
All units in one group can be controlled together.
Favourite position (heart symbol) In the ONYX app, you can save up to six
freely selectable brightness options for each ONYX.LED, which you can use
again later very easily.
Ideal use of the radio signal
In case of bad reception, the position of the ONYX.CENTER/ONYX.CLICK must be
changed.
Radio systems that send on the same frequency may cause interference with
reception. It must be considered that the range of the radio signal is limited
by statutory regulations and structural measures.
Installation Instructions and Instructions for Use
Fault removal
Problem
Lighting cannot be controlled in the ONYX app (offline).
Poor or no radio reception.
Possible cause
No mains voltage at the awning
Adverse position of the ONYX.CENTER or ONYX.CLICK
Troubleshooting
Check the mains voltage and establish it if necessary.
Change the position of the antenna of the ONYX.CENTER or re-position
ONYX.CENTER/ONYX.CLICK
Disposal
Dispose of the device in accordance with the current country-specific
regulations for electronic scrap (e.g. suitable collecting points).
Subject to technical modifications Date of Issue April/2022
57
58
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Control of the LED lighting with the control module Somfy
3 1
2
Information about the commissioning and operation of the LED lighting are
available in the instructions for use “White LED Receiver io” from Somfy.
Legend Power supply unit Control module Somfy Connection point
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
The electrical works in the low-voltage range (230 V AC) may be carried out by
a qualified electrician only. This applies particularly to modification works
on the supply unit (230 V AC – input side). The entire LED System in the
extra-low-voltage range (24 V DC) is situated after the secondary circuit of
the supply unit. However, in the event of personal adjustments, the
manufacturer HELLA shall assume no liability or warranty.
During works on the LED circuit, all LED lighting must be switched off and the
entire power supply to the awning should be disconnected. To this end,
disconnect the power supply directly from the house! When removing the awing,
the parts that are under prestress (e.g. folding arms) must be completely
released from tension and protected against unintentional extending before
removal.
Subject to technical modifications Date of Issue April/2022
59
60
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Basic structure of the LED lighting with control module for Somfy io/ONYX
3 4
7 4
Legend LED folding arm Control module Somfy io/ONYX Front rail Two-wire line
connector
1 4 6
1
2 5
Input lead 230 V Wiring 24 V LED strip
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Exchange procedure
1. Removing the defective arm and installing the new one: – Extend the awning
for approx. 500 mm – Secure the folding arms so that they can not fold out on
their own because of their
internal spring mechanism. Attention: There is danger to life! – Disconnect
the awning from the mains. For this purpose, switch dead the power supply
for the whole house. – Pull the 24 V power supply line (placed between folding
arm and arm bearing) out of the
awning cassette until the two-cord line connector is within reach. – Cut the
line directly before and after the two-cord line connector. – Remove the
folding arm from the front rail. – Drive out the joint bolt in the bearing
from the bottom up. Slightly support the folding arm
when doing so. – Now mount the new folding arm.
2
3
1
Legend Folding arm Two-cord line connector (Art. no.: 05510012) Arm bearing
Subject to technical modifications Date of Issue April/2022
61
62
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Exchange procedure
2. Provide the electrical connection (24 V) between folding arm and LED
control unit again. After the installation of the new folding arm, the
previously disconnected 24 V power supply line between the folding arm and the
LED control unit must be reconnected watertightly by means of a two-cord line
connector (art. no. 05510012). For this purpose push both wires in one side of
the two-cord line connector and connect the connector with the help of water
pump pliers on one side. Stripping of the wires is not required.
Connecting the wires in the two-cord line connector: – Red on Brown (positive
terminal) – Black on Blue (negative terminal)
2 1
3
Afterwards repeat this procedure for the 2nd side of the two-cord line
connector.
Note: Make sure, that both wires are shortened equally and flushly, are placed
correctly in the terminal and apply electrical contact.
Installation Instructions and Instructions for Use
Replacing a folding arm with integrated LED lighting
Exchange procedure
2
1
3
Stow the cable and the two-cord line connector in a loop-like manner in the
awning cassette. Stow the cable in the cassette and the arm bearing in such a
way, that the connection point does not get bent when retracting or extending
the awning and does not move.
Legend Cable (coating stripped) Wire negative terminal (not stripped) Wire
positive terminal (not stripped)
Subject to technical modifications Date of Issue April/2022
63
64
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Commissioning/functional check
Extend and retract the unit in and out completely. When extending the unit for
the first time, make sure no one is in the operating radius or standing below
the unit.
Make sure that during the later operation the units can be extended freely and
without blockings. Do not extend the unit, if objects or persons are in the
operating radius of the sun protection unit. Please observe the safety
instructions. After the first extending check the mounting material and the
construction elements for strength. Automatic control devices or switches,
that are not in the operator’s field of vision, may not be used for test runs
of motor driven units.
We recommend the use of a test cable for the provisional operation of the
motor.
Check all settings. Check all screwed connections for tightness.
The awning is a sun protection device that is only allowed to be used for the
intended use. Wrong use can put the user in danger. Additional loadings such
as objects that are sticked to the awning or cable tensionings can damage the
awning or lead to its crashing, and are therefore not allowed.
Clean the elements (see maintenance instructions).
Pass these instructions as well as possible instructions of the motor, switch
and control manufacturer on to the user. Brief the user, whereupon you provide
comprehensive information on the safety and user instructions of the system.
Have the correct design of the system as well as the installation and briefing
with the safety information confirmed in writing (see handover report).
Installation Instructions and Instructions for Use
Removal and Disposal
With removal or disposing of the awing, the parts that are under prestress
(e.g. articulated arms, counter draw systems) must be completely released from
tension and protected against unintentional drawing-out before removal. For
this, please contact a specialist enterprise.
Subject to technical modifications Date of Issue April/2022
65
66
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
Handing over report (for the fitter)
Dear Customer, We are glad that you have opted for a HELLA brand product. Our
units are fabricated with greatest care and many years of experience.
Your product Cassette awning CLEO 7040 was manufactured in accordance with EN
13561:2004+A1:2008 and was installed professionally and handed over
on the …………………………………………………………………………………………………………………… .
Sloping projection …………………………………………………………………………………………………….
Width …………………………………………………………………………………………………………………….. The instructions for use
and the installation instructions have been handed over and must be read
before using the product. An introduction has taken place. The safety
instructions were pointed out.
Installation Instructions and Instructions for Use
Handing over report (for the user)
Dear Customer, We are glad that you have opted for a HELLA brand product. Our
units are fabricated with greatest care and many years of experience.
Your product Cassette awning CLEO 7040 was manufactured in accordance with EN
13561:2004+A1:2008 and was installed professionally and handed over
on the …………………………………………………………………………………………………………………… .
Sloping projection …………………………………………………………………………………………………….
Width …………………………………………………………………………………………………………………….. The instructions for use
and the installation instructions have been handed over and must be read
before using the product. An introduction has taken place. The safety
instructions were pointed out.
Dealer
Name Place
Customer
Date Signature
Name Street Postal code Date
First name House number Place Signature
Subject to technical modifications Date of Issue April/2022
67
Dealer
Name Place
Customer
Date Signature
Name Street Postal code Date
First name House number Place Signature
68
Subject to technical modifications Date of Issue April/2022
Installation Instructions and Instructions for Use
HELLA Interior Venetian Blinds
regulate the lighting in a room very comfortably, immediately gracing it with
much more atmosphere.
HELLA Insect screens
and you decide who is allowed to come in and who isn’t.
HELLA Pleated Blind
folds up very compactly and protects very well against the sun and nosey
glances where only little space is available.
HELLA Outdoor Blinds
serve for the light regulation, as view protection, anti-glare blind and heat
protection.
HELLA Front-mounted Roller Shutter
for more safety and protection against rain, wind, heat, the cold, noise,
incident light and nosey glances, also available for subsequent installation.
HELLA Vertical awning
With toggle catch mechanism for a lovely façade design with perfect heat and
glare protection.
For questions, wishes and ideas: HELLA Infoline +43/(0)4846/6555-0
HELLA Sonnen- und Wetterschutztechnik GmbH A-9913 Abfaltersbach, No. 125
Phone: +43/(0)4846/6555-0 Fax: +43/(0)4846/6555-134 e-mail: office@hella.info
Internet: http://www.hella.info
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>