IMPECCA RA-2170 17 Cu. Ft. Refrigerator User Manual
- June 3, 2024
- IMPECCA
Table of Contents
17 CU. FT. Refrigerator
User Manual
Model: RA-2170/ RA-2170D2
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
- This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used.
- Do not allow children to climb, stand or hang on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Keep fingers out of the space between the doors and cabinet. Be careful closing doors when children are in the area.
- In refrigerators with automatic ice makers, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands near or on the automatic ice-making mechanism while the refrigerator is plugged in.
- Unplug the refrigerator before cleaning and making repairs.
- We strongly recommend that any servicing be performed by a qualified individual.
- Turning the temperature control dial to the “0” position stops cooling but does not shut off power to the refrigerator.
- Do not leave refrigerator in extremely cold or warm temperatures.
- Do not place refrigerator near heat sources or open flames.
- Clean the refrigerator with a soft, damp cloth. Remove stains with a mild soap. Do not clean the unit with industrial grade solvents, or abrasive chemicals.
- Do not place heavy items on top of the refrigerator.
- Never install the refrigerator where there is a lot of moisture or in areas where water can splash.
- Do not allow children to hang on the doors; the refrigerator may be tip over and hurt children.
- Never eat food that may have spoiled because it was stored too long in the refrigerator or was stored in an out-of-order refrigerator.
- Do not use sharp tools inside the refrigerator (such as an ice pick to remove ice) as damage may occur.
- If not using for a long period of time, remove all food from the refrigerator and unplug the unit.
- Before connecting the unit to the power source, let it stand upright for approximately 24 hours. This will reduce the possibility of a malfunction in the cooling system due to any handling during shipment.
BEFORE DISCARDING YOUR OLD REFRIGERATOR
Your old refrigerator may have a cooling system that used CFCs
(chlorofluorocarbons) or HCFCs (hydrochlorofluorocarbons). CFCs and HCFCs are
believed to harm stratospheric ozone if released to the atmosphere. If you are
going to throw away your old refrigerator, make sure the refrigerant is
removed for proper disposal by a qualified technician. Check with your
retailer to find out if they’ll take away and responsibly dispose of or
recycle your old refrigerator. For more information on Responsible Appliance
Disposal see: https://www.epa.gov/rad
CHILD ENTRAPMENT WARNING
Risk of child entrapment. Before you throw away your old refrigerator or
freezer:
- Take off the doors.
- Leave the shelves in place so that children may not easily climb inside.
CAUTION: USE OF AN EXTENSION CORD IS NOT RECOMMENDED.
FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS
GETTING STARTED
Thank you for purchasing this Impecca 10 Cubic Foot Refrigerator. Please
follow these operating instructions carefully. Keepthese instructions in a
safe place and consult them as needed.
Note: All images in this instruction manual are for indication only; the
physical appearance and options on your model may vary.
SERIAL AND MODEL NUMBER
Please record your model number and serial number belowYou can find the number
plate in the upper-left wall inside therefrigerator.
Model Number: _____
Serial Number: __
Date of Purchase: ____
SAFETY NOTICES
This appliance is intended to be used in household and simi applications
such as:
- Staff kitchen areas in shops, offices and other working environments
- Individual use in hotel rooms and other residential type environments
INSTALLING YOUR APPLIANCE
LOCATION
When selecting a position for your unit, ensure thefloor is a flat, level
surface and the room is well ventilated. Avoid locating your unit near a heat
source, such asan oven, stove top, boiler, or radiator. Also avoid
directsunlight as it may increase the electrical consumption.
Extremely cold ambient temperatures may also preventthe unit from operating
effectively. This unit is not designed for use in a garage or outdoor
installation. Do notplace any covering such as a drape or sheet on the unit.
When installing the unit, ensure that a minimum of 2 inches offree space is
left at both sides and in the rear, and 1 inch at thetop of the unit. This
will allow cold air to circulate around therefrigerator and improve the
efficiency of the cooling process.
The refrigerating system in this refrigerator is a “Frost Free”system. This
type of system requires no user intervention (i.e.defrosting) other than
selecting required cooling temperatures and the usual care and maintenance.
This unit is a FREE-STANDING INSTALLATION ONLY, and is NOT intended to be built-in. The unit’s door must be able to open fully as shown. W×D ≥ 50.8 inches × 58.5 inches
LEVELING THE UNIT
It is very important to keep the unit level, so that the door will close
properly and prevent problems that will cause effective cooling to fail. To
level the nit, turn the two adjustable feet clockwise or counterclockwise to
respectively raise or lower the corner.
Note: If the unit is not level, the door and magnetic seal alignments
will not be covered properly. Install this appliance in an area where the
ambient temperature is between 55°F (13°C) and 110°F (43°C). If the
temperature around the appliance is too low or high, cooling ability may be
affected.
CLEANING BEFORE USE
Wipe the inside of the unit with a weak solution of baking soda
(bicarbonate). Then rinse with warm water using a damp sponge or cloth. Wash
the shelves and bins in warm soapy water and dry completely before putting
back in the unit. Clean the exterior of the unit with a damp cloth.
GROUNDING INSTRUCTIONS
This appliance must be grounded. The refrigerator must be plugged into its own
dedicated 115 Volt electrical outlet. Performance may be affected if the
voltage varies by 10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is not covered under your
warranty The power cord of the appliance is equipped with a three-prong
grounding plug for your protection against electrical shock hazards. It must
be plugged directly into a properly grounded three prong receptacle. The
receptacle must be installed in accordance with local codes and ordinances. Do
not use an extension cord or adapter plug. You must make sure all three prongs
are in a 3-pronged outlet (see figure).
WARNING: Improper use of the grounding plug can result in a risk of
electric shock. Consult a qualified electrician or service person if the
grounding instructions are not completely understood, or if doubt exists as to
whether the appliance is properly grounded.
When using a 3-pronged outlet
UNIT DIAGRAM
Note: Above picture is for reference only. The actual appliance may be slightly different.
**DOOR HANDLE INSTALLATION
**
– Not applicable to all models.
The refrigerator must be disconnected before attempting the installation of
door handles.
Step 1: Install the two Phillips head screws into the doorholes and turn
screws until fully in place.
Step 2: Position the door handle on the screws installed in
Step 1.Step 3: Install screws at the hole located on the side of thehandle and
turn screws until completely tight. Installscrew caps as shown in the figure
above.
DOOR SWING REVERSAL (OPTIONAL)
It is advised that you determine if you need to reverse the door swing and
complete this procedure prior to installing and turning on your refrigerator.
Note: These instructions are for changing the hinges from the right side to
the left side. If you wish to change the hinges back to the right side, follow
hese same instructions and reverse all references to left and right.
CAUTION!! TO AVOID INJURY TO YOURSELF AND/OR PROPERTY, WE RECOMMEND
SOMEONE ASSIST YOU DURING THE DOOR REVERSAL PROCESS.
- Ensure the appliance is unplugged and empty.
- Adjust the two leveling feet to their highest position.
- Have something solid against which to rest the appliance. This will be necessary when it comes to taking off the door
- Avoid laying the refrigerator completely flat on its back as this may damage the cooling system.
TOOLS REQUIRED
- Phillips screwdriver
- Allen key wrench
- Flathead screwdriver
STEP 1: REMOVE THE FREEZER DOOR
Using a flathead screwdriver, gently pry and lift the right top hinge cover
and the left cover plate. Using a Phillip’s screwdriver, unscrew the screws of
the right top hinge. Remove the upper hinge. Raise the freezer door upward to
detach.
STEP 2: REMOVE THE REFRIGERATOR DOOR
Unscrew the three screws holding the center hinge with a Phillip’s
screwdriver. Remove the hinge and save the screws and hinge. Raise the
refrigerator door upward, as shown.
STEP 3: REPLACING THE BOTTOM HINGE
Unscrew the two screws holding the bottom hinge and remove the bottom hinge
from the bottom right side of the refrigerator. Unscrew the hinge pin from the
right side of the bottom hinge and move it to the left side of the
refrigerator. Secure the bottom hinge to the bottom left side of the
refrigerator using the screws you removed previously.
STEP 4: REFITTING THE DOOR HARDWARE
Remove the plastic bushing from the top right side of the freezer and cold
storage doors.
Remove the hole plug from the top left of the refrigerator door and insert it in the top right side of the refrigerator door.
Insert the plastic hole plugs into the left sides of the freezer and refrigerator doors.
STEP 5: REINSTALLING THE REFRIGERATOR DOOR
Remove the door block from the bottom right side of the cold storage door and
attach it to the left side of the door.
Attach the left upper door self-locking block and the left dooropen stopper to the left side of the freezer door.
Remove the right upper door self-locking block and the right door-open
stopper. Store in a safe place in case you need to reverse the door position
again.
Remove the two hole caps from the left side, where the center hinge will go,
and insert them into the right side. Attach the refrigerator door on the
ottom hinge and then attach the left center hinge to the left side of the
refrigerator.
STEP 6: REINSTALLING THE FREEZER DOOR
Put the freezer door onto the left center hinge and then attach the top left
hinge to the top of the refrigerator. Cover the hinge with the top left hinge
over and cover the screw holes on the right side of the top with the cover
plate (removed in a previous step).
STEP 7: REMOVING DOOR HANDLES
Remove the screw caps on the door handles. Use an Allen wrench to remove the
four Allen-screws securing the handles to the left side of the freezer and
efrigerator doors. Removethe handles.
STEP 8: REINSTALLING THE DOOR HANDLES
Remove the four Phillips-head screws from the left side of the freezer and
refrigerator doors. Screw the four Phillips-head screws into the holes on the
right side of the freezer and refrigerator doors. Attach the handles to the
right side of the freezer and refrigerator doors with the Allen-head screws
removed in a previous step. Tighten with the Allen wrench and replace the
screw caps.
STEP 9: REFITTING HOLE PLUGS AND HANDLE CAPS
Replace all handle hole plugs into the remaining holes on the left side. Refit
the handle caps onto the ends of handles to cov- er screw holes.
OPERATION
REFRIGERATOR TEMPERATURE CONTROL
Your refrigerator will automatically maintain the temperature level you
select. The temperature control has 4 settings. COLD is the warmest setting,
COLDEST is the coldest setting.
At first, set the panel to the COLDER indicator marking (middle setting), and
allow 24 hours to pass before adjusting the temperature to your need.
NOTE: If the refrigerator has been placed in a horizontal or
tiltedposition for any period of time, wait 24 hours before pluggingthe unit
in. The appliance may not operate at the correct temperature if it is in a
particularly hot environment, or if the door is opened toofrequently. Turning
this knob to “off” stops the cooling in boththe refrigeration and freezer
sections.
NOTE
- If the unit is unplugged, you must wait 3 to 5 minutes befrestarting the unit (plugging the unit back in). If you attempto restart before 3 to 5 minutes, the refrigerator will not st
- If the power goes out, the unit should restart itself when the power comes back on.
- Large amount of food will lower the cooling efficiency of the appliance.
- Do not place food so that it blocks an air vent, and leave adequate space between food items for air flow in the cabine
- Allow several hours for temperature to stabilize between two temperature selections.
FREEZER TEMPERATURE CONTROL
- Your refrigerator has a vent control for regulating the temperature in the freezer compartment. The temperature control is located on the center of the freezer compartment’s interior back panel.
- The first time you turn the unit on, adjust the temperature control knob to COLDEST and let the unit run for at least 2 hours before putting food inside. This will ensure that the freezer cabinet is thoroughly chilled before food is put in. The FREEZER temperature control has 4 settings: OFF, COLD,COLDER and COLDEST. COLD is warmest setting and COLDESTis coldest setting, OFF is off. ranges from COLD (the warmest)to COLDEST (the coldest). Adjust this control to get the desiredtemperature. The recommended factory setting is COLDER(halfway between COLD and COLDEST).
THE FREEZER COMPARTMENT
- This compartment is designed for the long-term storage of frozen food. Storage time period is up to three months.
- Place frozen food into the freezer as quickly as possible after purchase. If there are instructions on the package, carefully follow these instructions regarding storage times.
CARE AND MAINTENANCE
COOLING SYSTEM
This refrigerator is inclusive of a FROST FREE type cooling system, which
means you never have to defrost the freezer compartment. The defrost water is
routed into a defrost pan located near the compressor, where it then
evaporates.
CLEANING
Before cleaning the refrigerator or freezer, always disconnect the
refrigerator from the power supply. To clean the inside, use a soft cloth and
a solution of a tablespoon baking soda to one quart (4 cups) of water, or a
mild soap suds solution or mild detergent. Wash ice cube tray, drip tray, and
glide out shelves in a mild detergent solution, then wipe dry with a soft
cloth. Clean the outside with a damp soft cloth and some mild detergent or
appliance cleaner.
VACATION TIME
For short vacation periods, leave the control knob at the usual setting.
During longer absences:
- REMOVE ALL FOOD
- DISCONNECT UNIT FROM ELECTRICAL OUTLET
- LEAVE THE DOOR OPEN TO AVOID POSSIBLE FORMATIONS OF CONDENSATION, MOLD, OR ODORS
POWER FAILURE
Most power failures are corrected within an hour or two, and will not affect
your refrigerator temperatures. However, you should minimize the number times
you open the door while the power is off. During power failures of longer
duration, take steps to protect your food.
IF YOU MOVE
Remove, or securely fasten down, all loose items inside the refrigerator. To
avoid damaging the leveling legs, turn them all the way into the base.
SOME IMPORTANT RULES FOR THE CORRECT USE OF THE REFRIGERATOR
- Never place hot foods in the refrigerator
- Beverages should be stored in sealed containers
- Foods to be stored for a long time should be wrapped in cellophane or polyethylene, or kept in glass containers.
- Never place spoiled food in the refrigerator.
- Don’t overload the refrigerator.
- Don’t open the door unless necessary.
- Should the refrigerator be stored without use for long periods, it is suggested, after careful cleaning, to leave the door ajar to allow the air to circulate inside the unit in order to avoid the possible formations of condensation, mold, or odors.
FOOD STORAGE SUGGESTIONS
Fresh Food Compartment
- Never cover food compartment shelves with aluminum foil or any other shelf covering material which may prevent air circulation.
- Always remove porous store wrapping paper from meats, poultry, and fish. Meats should be wrapped individually and placed in a dish for storage. Wrap fish and poultry in foil or heavy waxed paper. Most fish should be used the same day of purchase. Packaged meats such as ham, bacon, dried beef, or frankfurter, store best in their original packages.
- Allow warm foods to cool to room temperature before placing them in the refrigerator.
- Always cover open dishes of food, especially leftovers. Use leftovers within 2 or 3 days.
VEGETABLE CRISPER
The tray at the bottom of the refrigerator is covered to retain moisture. The
crisper compartment will enable you to store vegetables and fruits which would
otherwise dry out rapidly. You can set the humidity on the crisper as follows:
- For low humidity: move the slider to the left
- For high humidity: move the slider to the right
LED LIGHTING REPLACEMENT
Do not change the LED light by yourself, please contact an authorized service
personnel.
TROUBLESHOOTING
The following simple issues can be handled by the user. Please contact customer support if the issues are not resolved.
PROBLEM | POSSIBLE CAUSE | SOLUTION |
---|---|---|
Unit does not work. | •No power to unit. |
•Power cord is unplugged.
•Wrong voltage is being used. Plug in unit.| •Check connection of power cord
at power source.
• Plug in unit.
•Use proper voltage.
Refrigerator running too cold.| •Temperature control too cold.
•Door not closed.
•Doors open . long/often.
•Close proximity to heat source or direct sun- light.| •Check/adjust settings
as needed.
•Close the door securely.
•Cool food before insertin g.
•Minimize door openings/duration.
•DO NOT place unit close to heat sources or in direct sunlight.
Internal temperature too cold.| • Temperature set too cold.| • Check/adjust
.ttings as needed.
Internal temperature not cold enough.| • No power to unit.
• Power cord is unplugged.
• Wrong voltage is being used.
• Temperature control too warm.
• Hot food inserted
• Doors open too long/often.
• Air flow obstructio.
• Close to heat source or direct sunlight| • Check connection of power cord at
power source.
• Plug in unit.
• U. proper voltage.
• Check/adjust settings as needed.
• Cool food before inserting.
• Minimize door openings/duration.
• Allow room for air to circulate around the unit.
• DO NOT place unit clo. to heat sources or in direct sunlight.
Freezer not cold enough.| • Temperature control too warm.
• Door not closed.
• A large quantity of warm food was inserted in the past 24 hours
• The appliance is placed near a heat source.
• Doors open too long/often.
• Wrong voltage is being used.| • Check/adjust settings as needed.
• Close door securely.
• Cool food before inserting.
• Minimize door openings/ duration.
• Use proper voltage.
Light will not work.| • No power to unit.
• Power cord is unplugged. Bulb .. is loose/needs replacing.
• Door switch is stuck.| • Check connection of power cord to power source.
• Plug in unit.
• Tighten or replace bulb.
• Check the switch for obstructions, clean if necessary.
Load noises| • Some amount of noise is normal, but if the noise is excessive,
the unit may not be level
• It may also be touching the wall or in contact with something el. in the
area.| • Adjust the leveling feet slightly
• Unplug the appliance and carefully move the it away from the wall or object
it is in contact with.
Additional notes:
- Condensation may be detected on the exterior surface and door seals of the freezer when the ambient humidity is high. This is a normal phenomenon, and the condensation can be wiped away with a dry towel.
- A slight buzzing noise will be generated by the compressor, especially when starting up or shutting down.
**ONE-YEAR LIMITED APPLIANCE WARRANTY (US)
**
Impecca® warravnts this product against defects in material and workmanship to
the original purchaser as specified below.
PARTS AND LABOR– if the product is determined to have a manufacturing defect,
within a period of one year from the date of the original purchase, Impecca®,
at its own discretion, will repair or replace the product parts at no charge
to you in the U.S.A.
To obtain warranty service by an authorized Impecca® service center, please
email us at: service@impecca.com to obtain a
Repair and Maintenance Authorization (RMA) number and received instructions on
how the repair and/or replacement procedure will take place.
Any glass materials included with the appliance will be covered for a period
of 60 days from purchase.
Impecca® specifically excludes from this warranty any non-electric/mechanical
attachments, accessories and disposable parts including but not limited to
outside case, connecting cables, batteries and AC adapters. Impecca® reserves
the right to repair or replace defective products with the same, equivalent or
newer models.
We reserve the right to either repair or replace product at our discretion.
Replacement may be either new or refurbished and while every endeavor will be
made to ensure it is the same model, if not possible it will be equal or
higher specification.
Normal “Wear and Tear” is not covered by this warranty. Further, Impecca®
hereby reserves the right to determine “Wear and Tear” on any and all
products. Tampering or opening the product casting or shell will void this
warranty in its entirety.
Eclusions: This warranty does not cover the following:
- Any product that has a defaced or covered serial number.
- Products that have been transferred to a second owner.
- Rust on the interior or exterior of the unit.
- Products listed as “As-Is” or “Refurbished.”
- Food loss due to any product failure.
- Window air conditioners installed in a wall.
- The product if used in a commercial setting.
- Service calls that do not involve product malfunction.
- Service calls for a product ruined by not following the provided instructions.
- Service calls to correct improper installation.
- Costs associated with making the product accessible for servicing (including but not limited to removal of trim/molding/cabinetry, etc.)
- Service calls to replace any consumables such as light bulbs, filters, etc.
- Surcharges that may apply to service calls on weekends, nights, holidays. Damages to the finish of appliance or household furnishings due to installation of appliance.
- Damages caused by any of the following: Acts of God; fires; misuse; accidents; incorrect power supply; service performed by unauthorized persons; use of non-genuine Impecca parts, etc.
ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO 1 YEAR FROM THE
DATE OF THE ORIGINAL RETAIL PURCHASE OF THIS PRODUCT.
THESE WARRANTIES AND REMEDIES ARE THE SOLE AND EXCLUSIVE WARRANTIES AND
REMEDIES IN CONNECTION WITH THE SALE AND USE OF THE PRODUCT. NO OTHER
WARRANTIES, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, ARE GIVEN.
IMPECCA® IS NOT RESPONSIBLE OR LIABLE FOR ANY DAMAGE, WHETHER SPECIAL,
INCIDENTAL, CONSEQUENTIAL, DIRECT OR OTHERWISE, OR WHETHER KNOWN OR SHOULD
HAVE BEEN KNOWN TO IMPECCA®, INCLUDING LOST PROFITS, GOODWILL, AND PROPERTY
AND PERSONAL INJURY RESULTING FROM ANY BREACH OF WARRANTY, THE INABILITY TO
USE THE PRODUCT OR UNDER ANY LEGAL THEORY IN CONTRACT OR TORT. IMPECCA
LIABILITY IS LIMITED TO THE ACTUAL PURCHASE PRICE PAID TO THE RETAIL SELLER OF
THE DEFECTIVE PRODUCT.
No Impecca® dealer, agent or employee is authorized to make any modification,
extension, change or amendment to this warranty without the written consent
and authorization from Impecca®.
Some states do not allow the exclusion or limitation of implied warranties or
liability for incidental or consequential damages, or do not allow a
limitation on how long an implied warranty lasts, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal
rights, and you have other rights, which vary from state to state.
Note: Our Warranty center services only to Continental U.S.A.
CUSTOMER SUPPORT
Before contacting customer support, please see the trouble- shooting guide
above.
Visit our website to contact us, find answers to Frequently Asked Questions,
and for other resources which may include an updated version of this user’s
manual.
If you wish to contact us by phone, please be sure to have your model number
and serial number ready and call us between 9:00am and 6:00pm ET, at +1
866-954-4440.
Keep tabs on Impecca’s newest innovations & enter contests via our social
network feeds:
www.impecca.com
www.facebook.com/Impecca/
www.instagram.com/impecca/
@impeccausa
Documents / Resources
|
IMPECCA RA-2170 17 Cu. Ft.
Refrigerator
[pdf] User Manual
RA-2170, RA-2170D2, RA-2170 17 Cu. Ft. Refrigerator, 17 Cu. Ft. Refrigerator,
Refrigerator
---|---
References
- pecca.com
- Responsible Appliance Disposal (RAD) | US EPA
- Impecca!
- Responsible Appliance Disposal (RAD) | US EPA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>