8BitDo Lite SE 2.4G Xbox Wireless Controller Instruction Manual

8BitDo Lite SE 2.4G Xbox Wireless Controller

Lite SE 2.4G Wireless Controller for Xbox

• Press the Xbox button to turn on the controller.
• Hold the Xbox button for 6 seconds to turn off the controller.
• Hold the Xbox button for 12 seconds to force the controller off.

Xbox

The latest system version of the Xbox console is required.

Wireless Connection

1. Connect the 2.4G adapter to the USB port of your Xbox console.
2. Press the Xbox button to turn on the controller.
3. Both LED indicators on the controller and the adapter will become solid when the connection is successful.

Wired Connection
Connect the controller to your Xbox console via a USB cable and wait till the controller is successfully recognized by the console, the Status LED will stay solid when the connection is successful.

Windows

Windows 10(1903) or above is required.

Wireless connection

1. Connect the 2.4G adapter to your Windows device.
2. Press the Xbox button to turn on the controller.
3. Both LED indicators on the controller and adapter will become solid when the connection is successful.

Wired Connection
Connect the controller to your Windows device via a USB cable and wait till the controller is successfully recognized by the device, the Status LED will stay solid when the connection is successful.

Button Swap

• The Profile LED indicators will blink continuously when the swapped button is pressed.
• The swapped buttons will revert to default settings if the controller is turned off or disconnected.
• View, Menu, Share, Xbox, P1, and P2 buttons are not supported.
  • Press and hold any of the two buttons you would like to swap, then press the Star button to swap them.
  • Repeat the same procedure to cancel the Button Swap.

P1/P2 Button Configuration

• Only one button on the controller can be remapped to the P1/P2 button (the Super Button), remapping multiple buttons are not supported.
• View, Menu, Share, and Xbox buttons are not supported for P1/P2 button configuration
  1. Connect the 8BitDo Super Button to P1/P2 port on the controller.
  2. Press and hold the [Super Button + the button you wish to configurel, then press the Star button to map this button to the Super Button.
  3. Press and hold the [Super Button + Star button] to cancel the button mapping.

Volume Control

• Press and hold the following button combos to adjust the balance between voice and game volume.
• Beeps when adjusted to maximum/middle/minimum value.
  • Press and hold the Profile button + D-pad up/down to turn up/down in-game volume.
  • Press and hold the Profile button + D-pad left/right to adjust the balance between voice and game volume.

Battery

• Status LED indicator → Low battery
• Battery charging → Battery full charged
• LED indicator → Red LED blinks
• Green LED blinks → Green LED stays solid

Built-in 1000mAh rechargeable lithium battery with 20 hours of play time over 2.4G wireless connection, with a charging time of 4 hours.

Safety Warnings

• Please always use batteries, chargers, and accessories provided by the manufacturer.
• The manufacturer is not liable for any safety issues arising from the use of non-manufacturer-approved accessories.
• Do not attempt to disassemble, modify, or repair the device yourself. Unauthorized actions may result in serious injury.
• Avoid crushing, disassembling, puncturing, or attempting to modify the device or its battery, as these actions can be dangerous.
• Any unauthorized changes or modifications to the device will void the manufacturer’s warranty.

Ultimate Software X

• Press the Profile button to activate, switch or deactivate the customized profiles. There is no profile in the default setting.
• • Please visit app.8bitdo.com to access the application.
    • It offers elite control over every aspect of your controller: customize button mapping, adjust the sensitivity of analog sticks and triggers, and control vibration intensity.

Re-pair the 2.4G Adapter
If the connection is lost or the adapter needs to be re-paired, you can follow the steps below to re-pair the controller with the adapter:

1. With the controller turned off, press and hold the Star + Profile + Xbox buttons to turn on the controller. The Status LED will blink rapidly.
2. Connect the 2.4G adapter to your Xbox console or Windows device, and wait for the controller to pair with the adapter automatically.
3. Both LED indicators on the controller and the adapter will become solid when the connection is successful.

Support
please visit support.8bitdo.com for further information & additional support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>