8BitDo DIY for MD User Manual
- June 3, 2024
- 8Bitdo
Table of Contents
8BitDo DIY for MD User Manual
Instructions – M30 Modkit
- Please handle it with care.
We are not responsible for any damage caused in use.
Press START to turn on the controller
Press and hold START for 3 seconds to turn off the controller
Press and hold START for 8 seconds to force turn off the controller
Bluetooth Connection
Switch
1. Press START +Yto turn on the controller, LED will blink4 times per cycle.
2. Press and hold MODE for 3 seconds to enter pairing mode. LED will rapidly
blink.
3. Go to your Switch Home Page to click on Controllers, then click on Change
Grip/Order and wait for controller to sync up. LED will become solid when
connection is successful.
4. Controller will auto reconnect to your Switch with the press of START once
it has been paired.
- When connected to your Switch, DOWN+HOME = Switch HOME button.
Android
1. Press START +B to turn on the controller, LED will blink once per cycle.
2. Press and hold MODE for 3 seconds to enter pairing mode. LED will rapidly
blink.
3. Go to your Android device’s Bluetooth setting, pair with [8B itdo M30 Mod
kit]. LED will become solid when connection is successful.
4. Controller will auto reconnect to your Android device with the press of
START once it has been paired.
Windows
1. Press START +X to turn on the controller, LED will blink twice per
cycle.
2. Press and hold MODE for 3 seconds to enter pairing mode. LED will rapidly
blink.
3. Go to yourWindows device’s Bluetooth setting, pair with [8Bitdo M30
Modkit]. LED will become solid when connection is successful.
4. Controller will auto reconnectto yourWindows device with the press of
START once it has been paired
MacOS
1. Press and hold START +A to turn on the controller, LEO will blink 3 times
per cycle.
2. Press and hold MOOE for 3 seconds to enter pairing mode. LEO will rapidly
blink.
3. Go to yourmacOS device’s Bluetooth setting, pair with [Wireless
Controller]. LEO will become solid when connection is successful.
4. Controller will auto reconnectto yourWindows device with the press of
START once it has been paired.
8Bitdo Retro Receivers and use Adapter
1. Press START +B to turn on the controller, LED will blink once per cycle.
2. Press both PAIR button on the receiver/Adapter and MOOE on the
controllerto sync them.
3. Both LEDs on the receiver/Adpter and controller will become solid when
connection is successful.
Button Mapping
Press and hold HOT KEY for 3 seconds to map\ OPAD and other buttons, LED will
blink once in red when successful:
HOME+ UP: DPAD = DPAD
HOME+ LEFT: DPAD = LEFT JOYSTICK
HOME+RIGHT: DPAD = RIGHT JOYSTICK
HOME+ DOWN: Swap A-B and X-Y
- Works only before connecting anything.
Battery
| Status | LED Indicator |
|---|---|
| Low battery mode | Red LED blinks |
| Battery charging | Red LEO stays solid |
| Battery fully charged | LED turns off |
Support
Please visit http://support.Bbitdo.com/for further information and additional support.
FAQ – Frequently Asked Questions
What devices is it compatible with?
It is compatible with Switch, Windows 10, Android, macOS, Raspberry Pi.
It will auto reconnect to any device with the press of START once it has they
paired successfully.
How can I upgrade the firmware?
When connected to Switch, you can find on these controllers:
A. Download the Firmware Updater from https://support.8bitdo.com/firmware-
updater.html first
B. Connect the board to your computer via a USB cable
C. Choose the right file for your kit to run
Can I map the buttons? What can I do if I incorrectly mapped the buttons?
Yes, you can map the buttons. This is what you can do if the buttons are
incorrectly mapped:
LEFT + HOME : set Dpad as left analogue stick
Up + HOME : reset Dpad
Right + HOME : set Dpad as right analogue stick
Press and hold any of the key combinations above for 5 seconds to map the buttons.
LED will blink in red to indicate the success of each button mapping.
*You need to reset the buttons manually.
How can I charge my controller after modifying it? How long can the battery last when fully charged?
We suggest you use a phone power adapter to charge the battery.
It uses a 180mAh rechargeable battery. It takes about one and half an hour to
fully and can last for about 10 hours.
Can I use it as a wired controller?
Yes, you can. Just use the USB cable which comes with it to connect to Switch, Windows 10, macOS, Android and Raspberry Pi.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>