Vari-Lite TCW Profile Light Engine User Manual
- August 30, 2024
- Vari-Lite
Table of Contents
TCW Profile Light Engine
“`html
Specifications
- Product: Profile Light Engine TCW/TWW
- Color Temperature: Tunable Cool White, Tunable Warm White
- Manufacturer: Vari-Lite
Product Information
The Profile Light Engine TCW/TWW is designed to provide tunable
cool white and tunable warm white lighting options. It is
manufactured by Vari-Lite, a company committed to delivering
high-quality customer service and support.
Usage Instructions
Technical Support
If you require technical support for the product, contact the
Service and Support team for online and field support, repair,
demo, commissioning, maintenance contracts, and technical
training.
Customer Service
For customer service inquiries related to boxed goods, spare
parts, order entry, project delivery, warranty fulfillment, and
repairs, contact the Customer Service team.
Additional Documentation
Visit the Vari-Lite website to access additional product
documentation, including DMX maps, software, and photometric
reports. For information on DMX512 control systems, refer to the
Recommended Practice for DMX512 by the United States Institute for
Theatre Technology.
Safety Warnings
Before installing, operating, or maintaining the fixture, read
the user manual carefully to ensure safety. Only qualified
personnel should perform installation and operation. Follow all
safety instructions provided to prevent damage or injury.
Caution Against Direct Sunlight Through Front Lens
Assembly
Avoid exposing the front lens assembly to direct sunlight to
maintain efficient light output from the luminaire’s lamp.
Caution Against Powering Luminaires from Dimmer Circuits
Avoid powering the luminaire from dimmer circuits as it may lead
to power problems, mis-operation, or failure due to the modified AC
wave form output.
FAQ
Q: Can I use the Profile Light Engine TCW/TWW with a
dimmer?
A: It is not recommended to power the luminaire from a dimmer
circuit to prevent potential power issues and malfunctions.
“`
PROFILE LIGHT ENGINE
TUNABLE COOL WHITE TUNABLE WARM WHITE
User ManUal
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
InTrODUCTIOn
OUR GOAL
We are committed to providing you the highest quality in customer service. Our
comprehensive resources are available to help your business succeed and ensure
you get the full benefit of being a Vari-Lite customer.
TECHNICAL SUPPORT
Our Service and Support team is tasked with online and field support, repair,
demo, commissioning, maintenance contracts, and technical training for
fixtures and systems. In addition, this team plays a large role in a Systems
sales, responsible for administering final commissioning, record-keeping, and
organizing services. Refer to the back cover of this User Manual for contacts
in your region or visit www.vari-lite.com/support
CUSTOMER SERVICE
Customer Service is responsible for boxed goods and spare parts quotations,
order entry and fulfilment, project delivery, lead times, and general account
management. They also manage all after sales warranty fulfilment, RGA, and
repairs invoicing in tandem with our After Sales Service & Support team. Visit
our website to find a customer service agent in your region.
ADDITIONAL DOCUMENTATION
Additional product documentation, including DMX maps, software, and
photometric reports, are available for download on our website. For more
information on installing DMX512 control systems, the following publication is
available for purchase from the United States Institute for Theatre Technology
(USITT), “Recommended Practice for DMX512: A Guide for Users and Installers,
2nd edition” (ISBN: 9780955703522). USITT Contact Information:
USITT 315 South Crouse Avenue, Suite 200 Syracuse, New York 13210-1844 USA
Phone: 800-938-7488 or
+1-315-463-6463 Fax:
866-398-7488 or
+1-315-463-6525 Website: www.usitt.org
ABOUT THIS DOCUMENT
Read all instructions before installing or using this product. Retain this
User Manual for future reference. Additional product information and
descriptions may be found on the product data sheet(s) which can be downloaded
from the website at www.vari-lite.com. This User Manual provides necessary
information regarding safety, installation, operation and routine maintenance
for Profile Light Engine TCW/TWW. Familiarizing yourself with this information
will help you to get the most out of your product.
WARNING: It is important to read ALL accompanying safety and installation
instructions to avoid damage to the product and potential injury to yourself
or others.
2
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
SAFETY WARNINGS AND NOTICES
Read this user manual in full before attempting to install, operate or
maintain the fixture to which it relates. This user manual is intended to
provide general guidance to such suitably qualified personnel. Installation
and operation of the fixture are to be performed by qualified personnel only.
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
· For indoor, dry location use only. Do not use outdoors unless fixture is
suitably IP rated. · Use safety tether when mounting. · Equipment should be
mounted in locations and at heights where it will not be readily subjected to
tampering by unauthorized personnel. · Not for residential use. Do not use
this equipment for other than intended use. · Note distance requirement(s)
from combustible materials or illuminated objects. Do not mount near gas
or electric heaters. · Install only in locations with adequate ventilation.
Ensure sure that ventilation slots are not blocked. · Ensure that the voltage
and frequency of the power supply match the power requirements of the
fixture. · The fixture must be earthed/grounded to the appropriate conductor.
· Do not operate fixture outside the specified ambient temperature range. · Do
not connect the fixture to any dimmer pack. · The use of accessory equipment
not recommended by the manufacturer may cause an unsafe condition
and void warranty. · Refer service to qualified personnel. This fixture
contains no user serviceable parts. · Prior to first use, carefully inspect
fixture to ensure no damage has occurred during shipping. · Materials used in
the manufacturing process can cause strong odors when the product is new.
These
odors dissipate over time. · Prior to each use, carefully inspect power cables
and replace any damaged cables. · Exterior surfaces of the luminaire will be
hot during operation. Take appropriate precautions. · Continuous use of the
fixture may shorten the lifespan. Power down the fixture when not in use. · Do
not cycle power on and off repeatedly. Disconnect mains power if the fixture
is not used for an
extended period. · Clean fixtures regularly, particularly when working in a
dusty environment. · Never touch power cables or wires while the fixture is
powered on. · Avoid entangling power wires with other cables. · In the event
of a serious operating problem, immediately discontinue using the fixture. ·
It is hazardous to operate luminaires without lens or shield. Shields, lenses,
or ultraviolet screens shall be
changed if they have become visibly damaged to such an extent that their
effectiveness is impaired, for example, by cracks or deep scratches. ·
Original packing materials can be reused for transporting the fixture. · Do
not look directly at the LED light beam while the fixture is on. · This is a
Class A product. In a domestic environment this product may cause radio
interference, in which case, the user may be required to take adequate
measures. · The light source contained in this luminaire shall only be
replaced by the manufacturer or service agent or similarly qualified person.
SAVE THESE INSTRUCTIONS.
WARNING: Refer to National Electrical Code® and local codes for cable
specifications. Failure to use proper cable can result in damage to equipment
or danger to personnel. Caution Against Direct Sunlight Through Front Lens
Assembly
3
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
CaUTIOn aGaInsT DIreCT sUnlIGHT THrOUGH FrOnT lens asseMBlY
The design and nature of the front lens assembly in Vari-Lite LLC luminaires
is to efficiently focus the light energy from the luminaire’s lamp for maximum
light output.
· When the front lens assembly is exposed to direct sunlight or intense light
from neighboring fixtures, the lens will collect and intensify this light and
focus it back into the fixture. Intense sunlight or beams from other fixtures
can cause damage to internal assemblies contained within the fixture.
· When fixture is not in use and direct sunlight or other intense light is
present, position luminaires so their front lens assembly it not directly
exposed to the light source.
CaUTIOn aGaInsT POWerInG lUMInaIres FrOM DIMMer CIrCUITs
It is not recommended to power any Vari-Lite LLC luminaire from a dimmer –
even in `NONDIM’ mode. Dimmer and non-dim modules are not suitable sources of
power because their output modifies the AC wave form. This may work for a
short time, but eventually results in power problems, luminaire mis-operation
and/or failure.
· When using a power distribution rack, do not use dimmer or non-dim modules
to power any Vari-Lite LLC luminaire. Damage to the luminaire can occur.
· Using a dimmer or non-dim module to power your Vari-Lite LLC luminaire will
void your luminaire’s warranty.
CaUTIOn aGaInsT THe Use OF THIrD ParTY ParTs Or aCCessOrIes
· Heat and heat distribution are important factors when operating Vari-Lite
LLC luminaires. Vari-Lite LLC luminaires are designed to dissipate heat
efficiently and safely. Any blockages or obstructions, such as aftermarket
baffles, covers, enclosures, etc. can interrupt the luminaire’s ability to
dissipate heat properly and can damage the luminaire.
· Vari-Lite LLC cannot be responsible for issues arising from non-approved
parts and accessories installed on or used with any Vari-Lite LLC product.
Customers of such products should contact the manufacturer directly for
assistance and support.
TRANSPORTING LUMINAIRES
When shipping or transporting luminaires, Vari-Lite LLC recommends that the
luminaire(s) be sufficiently protected against any (including, but not limited
to) shock, vibration, drops, jarring, exposure to the environment, etc.
Failure to sufficiently protect any Vari-Lite LLC luminaire during shipping or
transportation will result in damage and void the luminaire’s warranty. Vari-
Lite LLC will not be responsible for any shipping damage or breakage of any
product under any circumstances. Vari-Lite LLC will not be responsible for any
third party case manufacturer’s cases.
NOTE: As with all automated luminaires, proper handling and suitable
protective shipping cases should be used when transporting fixtures to reduce
the risk of damage.
TransPOrTaTIOn anD sHIPPInG Case reQUIreMenTs
Cases to transport Vari-Lite LLC luminaires should meet the following loading
requirements: · Luminaire head, yoke, and enclosure sub-assemblies shall be
equally supported and constrained where no one sub-assembly (head, yoke, or
enclosure) fully supports the entire mass of the luminaire. · The interior of
the case shall be of high quality and uniform density foam. The foam shall be
of the same type and density throughout as to equally and uniformly support
loading at every contact surface. · The case shall, when laid on any of its
six (6) surfaces, maintain the loading requirements outlined above. · All
cases not meeting the aforementioned loading requirements, with wheels, shall
have markings on the exterior of the case that the unit is to be transported
on it wheels only (e.g. “Case must be transported and remain [at all times] on
its wheels”).
4
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
COMPLIANCE NOTICE
FCC DECLARATION OF CONFORMITY
This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when this
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with Vari-Lite system, service, and safety guidelines, may cause
harmful interference to radio communications. As tested under this standard:
FCC 47CFR 15B clA*CEI Issued:2009/10/01 Title 47 CFR Part 15 Subpart B
Unintentional Radiators Class A Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his/her own expense.
EU DECLARATION OF CONFORMITY
We, Vari-Lite LLC., 10911 Petal Street, Dallas, Texas 75238, declare under our
responsibility for the products contained herein are in conformity with the
essential requirements of the following European Directives and harmonized
standards:
Low Voltage Director (LVD), 2006/95/EC EN 60589-2-17:1984+A1:1987+A2:1990 used
in conjunction with 60598-1:2008/A11:2009
Electromagnetic Compatibility Directive (EMC), 2004//108/EC EN 55022:2010,
EN55024:2010
5
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
HOW TO OBTAIN WARRANTY SERVICE
A copy of the Limited Warranty card was included in the shipping package for
this product. To obtain warranty service, please contact customer service at
1-214-647-7880, or
entertainment.service@ signify.com and request a Return Material Authorization
(RMA) for warranty service. You will need to provide the model and serial
number of the item being returned, a description of the problem or failure and
the name of the registered user or organization. If available, you should have
your sales invoice to establish the date of sale as the beginning of the
warranty period. Once you obtain the RMA, pack the unit in a secure shipping
container or in its original packing box. Be sure to clearly indicate the RMA
number on all packing lists, correspondence, and shipping labels. If
available, please include a copy of your invoice (as proof of purchase) in the
shipping container.
With the RMA number written legibly on or near the shipping address label,
return the unit, freight prepaid, to:
Vari-Lite LLC Attention: Warranty Service (RMA# ____) 10911 Petal Street
Dallas, Texas 75238 USA
As stated in the warranty, it is required that the shipment be insured and FOB
our service center.
IMPORTANT! When returning products to Vari-Lite for repairs (warranty or out-
of-warranty) from a country other than the USA, “Vari-Lite LLC”, must appear
in the address block as the Importer of Record (IOR) on all shipping
documentation, Commercial Invoices, etc. This must be done in order to clear
customs in a timely manner and prevent returns.
6
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
1 DesCrIPTIOn
F E AT U R E S
· High output midsized LED theatrical luminaires – modern fixtures with
quality you can trust.
· Tunable white with >94 CRI – adjust color temperature without compromising
output or quality of light.
· Quiet operation with variable fan control – perfect for use in quiet
environments.
· Adjustable frequency to exceed camera frame rates – camerafriendly fixtures
for IMAG, event recordings, or TV and film applications.
For detailed product information, please refer to the Product Guide at
https://www.vari-lite.com/global/products/leko-ledprofile-tcw
COMPONENTS
The document provides installation and operation instructions for the
following products: · Profile Light Engine TCW or Profile Light Engine TWW
Read all instructions before installing or using this product. Retain this
manual for future reference. Additional product information and descriptions
may be found on the product specification sheet.
INCLUDED ITEMS
Each Profile Light Engine TCW or TWW luminaire includes the following items: ·
Profile Light Engine TCW or Profile Light Engine TWW
LEKO_LED_PROFILE
· TrueOne compatible power connector · Quick Start Guide
INCLUDED ITEMS
Profile Light Engine TCW or TWW
QUICK START GUIDE
POWER CONNECTOR WARRANTY CARD
7
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
2 InsTallaTIOn
MOUNTING
The unit should be mounted via its screw holes on the bracket. Always ensure
that the unit is firmly fixed to avoid vibration and slipping while operating.
Always ensure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Always use a
safety cable that can hold up to 12 times the weight of the unit when
installing the fixture. The luminaire must be mounted by professionals.
INSTALLING SHUTTER ASSEMBLY AND LENS TUBES
To install shutter/lens: Step 1. Slide shutter assembly into the body. Clamp
in place with shutter retainer and tighten knob. Step 2. Pull he locking lever
on the lens tube toward the front of the lens. Step 3. Slide the lens tube
down into the body until the locking lever can latch. Loosen focus lock knob
and
adjust focus as desired. Tighten to lock. Reverse process to remove. (SPX lens
shown). Visit www.vari-lite.com for a complete list of compatible lens tubes.
NOTE: Lens tube may need to be moved foward (away from the body) on PLT or internal lenses moved forward on SPX to install or remove. Loosen focus lock knob to adjust.
8
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
3MenU OPeraTIOn
CONTROL PANEL
Press the MENU button to select any functions, until the required function is
shown in the display. Select the desired function by pressing ENTER, which
will cause the display to blink. Use the UP and DOWN button to change the
mode. Once the required mode has been selected, press the ENTER button to
accept the selection. Press MENU to return to the previous menu or let the
unit idle for one minute to exit menu mode automatically.
9
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
LEVEL 1 address Configure
DMX Fixture
LEVEL 2
LEVEL 3
LEVEL 4
LEVEL 5
LEVEL 6
001~506(16 Bit), 001-508(8 Bit), 001-511(2 Channel)
leD Hours
XXXXXX h
reset leD Hour
are you sure?
square Curve
Dimming Curve
s Curve
linear Curve
Dim snap
On (Fast) Off (slow)
standard
leD
Output Mode
studio Whisper
Fan Mode
On auto
1200Hz
2500Hz
leD Frequency
5000Hz 10000Hz
20000Hz
25000Hz
30 sec
Disp Timeout
5 Min 10 Min
On
reset
Yes/no
address
001~506(16 Bit), 001-508(8 Bit), 001-511(2 Channel)
16 Bit
DMX Mode
8 Bit
2 Channel
Hold
DMX Fail
Blackout
Go to Preset
Ch 1 – Intensity XXX (Value)
Data
Ch 2 -Intensity Fine XXX (Value)
…all functions
UID
UID electronic format
status
(no errors..or displays a list of errors)
reboot Fixture
are you sure?
Version
VXXX
Fixture Hours
XXXXXX h
Crossload (software) send
Fan Check
X rpm
service
Diagnostics
Board Check
(no errors..or displays a list of errors)
sensor Check X °C
DEFAULT 001 Default
Default Default
Default Default
Default
001 Default Default
10
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
LEVEL 1
LEVEL 2
Playback
Manual Preset
edit Programs
LEVEL 3 Power Up Preset Intensity Priority Power Up? load Preset edit settings
store Clear Clear all
LEVEL 4 01 – 20 0 – 255 Preset DMX Off On 01 – 20 Intensity Cool or Warm
nautural
01 – 20
LEVEL 5
0 – 255 0 – 255 0 – 255 are you sure?
01 – 20 are you sure?
are you sure?
Yes no
LEVEL 6
Yes no Yes no
DEFAULT
255 Default
Default
11
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
MENU SYSTEM
USER MANUAL
DISPLAY AND MENU SYSTEM OPERATION
The Display Menu system consists of several categories. Use the Menu Button to
access the menu. Then use the Up/Down arrow to navigate. When you reach the
desired item, touch the Enter Button. To go backwards, touch the Menu Button.
To navigate and access menu settings/selections: Step 1. Make sure unit is
powered and turned on. Step 2. Touch [MENU] to access menu categories. Step 3.
Use two Arrow () buttons to navigate through the various options and settings.
Step 4. Once menu item is reached, touch [ENTER] to access the menu item
parameters. Step 5. Make changes to parameters as desired. Step 6. Press
[ENTER] button to accept changes.
ADDRESS
ADDRESS
Sets the starting DMX address for the fixture. Can also be set via RDM.
CONFIGURE
LED
This menu allows for viewing the LED engine hours, setting the dimming curve,
dim snap, output mode, fan mode, and LED frequency.
LED Hours Displays the current LED engine hours.
Reset LED Hours Allows the LED hours of the engine to be reset. Should only be
done if the engine has been replaced
Dimming Curve Select from Linear, S-Curve and Square Law. Can also be set via
the control channel and RDM.
Dim Snap Dim Snap On allows for fastest output changes between levels but
reduces smoothness dimming the LED engine. Dim Snap Off ensures all fades
between output levels remains smooth and flicker free but limits fast, instant
snaps between levels. Can also be set via the control channel and RDM.
Output Mode Standard mode provides full LED output. Studio mode reduces fan
speed to reduce the fan noise of the fixture. Whisper mode decrease the fan
noise further. In both Studio mode and Whisper mode, the LED output will
decrease accordingly. Can also be set via the control channel and RDM.
Fan Mode Fan On runs fans at continuous max speed based on Output Mode. Fan
Auto will reduce/increase speed on demand based on LED operating temperature.
The fan will not exceed the maximum permissible level based on Output Mode.
Can also be set via the control channel and RDM. See Appendix B.
12
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
LED Frequency Choose the refresh rate of the LED engine (see Display Menu Tree
for list).
USER MANUAL
DISPLAY TIMEOUT
Sets how long the display remains illuminated after the last button touch.
Choose from 30 seconds, 5 minutes, 10 minutes, or always on.
RESET
Resets all the factory defaults of the fixture. This includes setting the DMX
Address to 001. Can also be done via RDM and via the control channel.
NOTE: Control channel will not change the current DMX address.
DMX
ADDRESS
Sets the starting DMX address of the fixture. Can also be set via RDM.
DMX MODE
16 Bit 16 Bit DMX control of Intensity and CCT, plus 8 Bit DMX control of
Strobe, Fan and Luminaire Control.
8 Bit 8 Bit DMX control of Intensity, CCT, Strobe, Fan and Luminaire Control.
2 Channel 8 Bit DMX control of Intesnity and CCT.
DMX FAIL
DMX Hold If DMX is lost, fixture will maintain its present state until DMX is
restored.
Blackout If DMX is lost, fixture will go to blackout until DMX is restored.
Goto Preset If DMX is lost, fixture will go to the preset (1 through 20).
DATA
Allows the current DMX value present on each of the luminaire’s DMX channels
to be viewed.
13
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
FIXTURE
UID
Displays the UID as set in the luminaire.
S TAT U S
Shows list of error message from previous calibration. If none, it will say No
Errors.
REBOOT FIXTURE
Restarts the entire operating system of the fixture. Can be performed via the
control channel or RDM.
VERSION
Shows the current software version of the fixture. Version is listed in
MM/DD/YY format. Can be viewed via RDM.
FIXTURE HOURS
Shows the accumulated hours the fixture has been powered on. Can be viewed via
RDM.
CROSSLOAD (SOFTWARE)
Allows the current version of software installed in the fixture to be sent to
other units via an attached DMX cable.
SERVICE – DIAGNOSTICS
Fan Check Shows the current fan speed in RPM.
Board Check Shows the current status of the control board.
Sensor Check Shows the current temp at the LED in °C.
MANUAL PRESET
P L AY B AC K
Power Up Preset Selects the preset (1 to 20) that will be played back after
power up if enabled.
Intensity Selects the master intensity of a preset being played back (0 to
255).
Priority Choose Preset if you always want a preset to playback. Choose DMX if
you only want a preset to playback if there is no DMX present.
Power Up? Choose Preset On if you want the fixture to playback the preset at
power up. Choose Preset Off if you do not want a preset to play.
14
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
EDIT PROGRAMS
Load Preset Select from preset 1 to 20 and touch [ENTER]. That preset will be
played back.
Edit Settings Choose the function from the list you wish to edit and touch
[ENTER]. Use the [UP]/[DOWN] buttons to set desired value. Touch [ENTER] to
store. Then continue to adjust all function desired.
Store After setting all your functions, select which preset number you wish to
store (1 to 20) and touch [ENTER]. Touch [ENTER] again to confirm when
prompted.
Clear Select the preset (1 to 20) you wish to clear and touch [ENTER]. Touch
[ENTER] again to confirm when prompted.
Clear All Presets When prompted, touch [ENTER] to confirm and all presets (1
to 20) will be erased.
WARNING: Clearing the presets CANNOT be undone!
15
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
4DMX MaPPInG
The fixture can be operated by DMX controller. The following tables assumes a DMX start address of 1. When a different starting address is used, this address becomes channel 1 function and other functions follow in sequence.
TABLE 1.16 BIT
DMX CHANNEL
PARAMETER
DEFAULTS
RANGE DMX
DESCRIPTION
1
Intensity (High)
0
0 – 65535 16-bit Intensity (Dimmer) Control
2
Intensity (low)
0 – 100% Outut
0 – 255
Control of strobe
0 – 9
no strobe Function – shutter open
10 – 99
strobe s>>>>>F
3
strobe
0
100 – 109 no strobe Function – shutter open
110 – 179
lighting strobe s>>>>>F
180 – 189
no strobe Function – shutter open
190 – 255 random strobe s>>>>>F
0 – 255
Dynamic control of fan speed vs leD output
0 – 4
automatic fan/output adjustment
4
Fan Control
linear control fo fan speed and leD output* 0
DMX 5 = Highest Constant Fan speed 5 – 255
DMX 255 = lowest Constant Fan speed
- standard mode only
0 – 255
Control Channel used for fixture settings
set discrete value of desired effect, wait >3 seconds,
then set value to 0 (idle)
**Function does not require 3 second rule to activate function
0 – 5
Idle (Default must be 0)
6 – 10
Full luminaire re-Cal – also wakes from shutdown
11 – 15
Fixture shutdown
16 – 20
reserved
21 – 25
Display – Menu On
26 – 30
Display – Menu OFF
31 – 40
reserved
41 – 45
Dimming Curve linear**
46 – 50
Dimming Curve s-Curve**
5
Control Channel
0
51 – 55
Dimming Curve square law (Default)**
56 – 60
reserved
61 – 65
Dimmer snap On**
66 – 70
Dimmer snap Off (Default)**
71 – 110
reserved
111 – 115
standard Mode (Default)
116 – 120
studio Mode – reduced output with lower fan
121 – 125
Whisper Mode – reduced output with lower fan
126 – 135
reserved
136 – 140 Fan On (Default)
141 – 145
Fan auto
146 – 170 reserved
171 – 175
reset defaults
176 – 255 reserved
6
CCT High
7
CCT low
Tunable leD array 0 – 100%
0
0 – 65535 0 = 4000K (TCW) or 2700K (TWW)
255 = 6500K (TCW) or 4500K (TWW)
16
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
TABLE 2.8 BIT
DMX CHANNEL
PARAMETER
1
Intensity
2
strobe
3
Fan Control
4
Control Channel
5
CCT
DEFAULTS 0 0 0
0
0
RANGE DMX
DESCRIPTION
0 – 255
0 – 255 0 – 9
10 – 99 100 – 109 110 – 179 180 – 189 190 – 255 0 – 255
0 – 4
5 – 255
0 – 255
0 – 5 6 – 10 11 – 15 16 – 20 21 – 25 26 – 30 31 – 40 41 – 45 46 – 50 51 – 55
56 – 60 61 – 65 66 – 70 71 – 110 111 – 115 116 – 120 121 – 125 126 – 135 136 –
140 141 – 145 146 – 170 171 – 175 176 – 255
0 – 255
8 bit Intensity (Dimmer) Control 0 – 100% Output Control of strobe no strobe Function – shutter open strobe s>>>>>F no strobe Function – shutter open lighting strobe s>>>>>F no strobe Function – shutter open random strobe s>>>>>F Dynamic control of fan speed vs leD output automatic fan/output adjustment linear control fo fan speed and leD output DMX 5 = Highest Constant Fan speed DMX 255 = lowest Constant Fan speed standard mode only Control Channel used for fixture settings set discrete value of desired effect, wait >3 seconds, then set value to 0 (idle) Function does not require 3 second rule to activate function Idle (Default must be 0) Full luminaire re-Cal – also wakes from shutdown Fixture shutdown reserved Display – Menu On Display – Menu OFF reserved Dimming Curve linear Dimming Curve s-Curve Dimming Curve square law (Default) reserved Dim snap On Dim snap Off (Default) reserved standard Mode (Default) studio Mode – reduced output with lower fan Whisper Mode – reduced output with lower fan reserved Fan On (Default) Fan auto reserved reset defaults reserved Tunable leD array 0 – 100% 0 = 4000K (TCW) or 2700K (TWW) 255 = 6500K (TCW) or 4500K (TWW)
17
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
TABLE 3.2 CHANNEL
DMX CHANNEL
PARAMETER
1
Intensity
2
CCT
DEFAULTS 0
0
RANGE DMX
DESCRIPTION
0 – 255 0 – 255 5 – 255
8 bit Intensity (Dimmer) Control 0 – 100% Output Tunable leD array 0 – 100% 0 = 4000K (TCW) or 2700K (TWW) 255 = 6500K (TCW or 4500K (TWW) linear control fo fan speed and leD output DMX 5 = Highest Constant Fan speed DMX 255 = lowest Constant Fan speed standard mode only
18
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
TABLE 4.CONTROL CHANNEL
DMX RANGE
ITEMS
DESCRIPTION
POWER CYCLE RULES
Control channel used for fixture settings
0 – 255
Control Channel
set discrete value of desired effect, wait >3 seconds, then set value to 0 (idle)
n/a
**Function does not require 3 second rule to activate function
0 – 5 Idle (Default)
Default value used to active functions. should default to 0
n/a
6 – 10
Full luminaire reCal
recalibrates all functions in the luminaire. also used to wake from shutdown
n/a
11 – 15
Fixture shutdown
shuts down all fixture output and turns off all fans. Fixture can be re- actived by a power cycle or via the reCal command
Will restart normally
16 – 20 reserved
21 – 25
Display – Menu On
switches UI display on remotely – Display will time out as set in UI
n/a
26 – 30
Display – Menu Off
switched UI display off remotely if on.
n/a
31 – 40 reserved
41 – 45
Dimming Curve linear**
selects linear Dimming Curve
Holds setting on power cycle
46 – 50
Dimming Curve s-Curve**
selects s-law Dimming Curve
Holds setting on power cycle
51 – 55
Dimming Curve square law (Default)**
selects square law Dimming Curve
Holds setting on power cycle
56 – 60 reserved
61 – 65
Dimmer snap On**
allows for fastest output changes between levels but reduces smoothness of dimming and color
Holds setting on power cycle
66 – 70
Dimmer snap Off ensure fades between levels remain smooth and flicker free
(Default)**
but limits instand snaps
Holds setting on power cycle
71 – 110 reserved
111 – 115
standard Mode (Default)
standard mode – Full leD output + full continuous fan at max speed (loudest setting). Fan remains at constant speed (unless in fan auto mode). nC40
Holds setting on power cycle
116 – 120 studio Mode
studio mode – Fan speed reduced to reduce dB levels 10% of full speed and leD output approximatly 80% of standard. Fan remains constant speed (unless in fan auto mode). nC35
Holds setting on power cycle
121 – 125 Whisper Mode
Whisper Mode – Fan speed reduced to reduce dB levels 30% of full speed and leD output approximatly 60% of standard. Fan remains constand speed (unless in fan auto mode). nC25
Holds setting on power cycle
126 – 135 reserved
136 – 140 Fan On (Default) Fan runs at continuous speed for selected output mode
Holds setting on power cycle
141 – 145 Fan auto
Fans will increase/decrease speed based on leD operation
Holds stting on power cycle
146 – 170 reserved
171 – 175 reset default
resets all paramters to factory default with the exception of DMX address and fixture DMX Mode
n/a
176 – 255 reserved
FUNCTION SELECTION VIA UI
n/a
n/a Yes Yes, press Menu twice to wake
Button press turns display on n/a
Yes Yes Yes
Yes Yes
Yes
Yes
Yes
Yes Yes
Yes, but will reset DMX address and
DMX Mode
19
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
20
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
DMX512 CONNECTION
· At last unit, the DMX cable has to be terminated with a terminator. Solder a
120 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 5-pin XLR-plug
and plug it in the DMX-output of the last unit.
· Connect the unit together in a daisy chain
by XLR plug from the output of
the unit to the input of the next unit. The cable cannot branched or split to
a Y
cable. DMX 512 is a very high-speed signal. Inadequate or damaged
cables, soldered joints or corroded connectors can easily distort the signal
and shut down the system.
· The DMX output and input connectors are pass-through to maintain the DMX
circuit, when one of the units’ power is disconnected.
· Each lighting unit needs to have an address set to receive the data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are equal
to 1).
· The end of the DMX 512 system should be terminated to reduce signal errors.
· 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal
(+), Pin 4/Pin 5: Not used.
21
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
5rDM ParaMeTer IDs
Remote Device Management (RDM) is a protocol enhancement to USITT DMX512 that allows bi-directional communication between a lighting or system controller and attached RDM compliant devices over a standard DMX line. This protocol will allow configuration, status monitoring, and management of these devices in such a way that does not disturb the normal operation of standard DMX512 devices that do not recognize the RDM protocol.
Model ID 0x0116 0x0117
LEKO LED OUTDOOR, RDM PRODUCT PARAMETER IDS
Manufacturer
Vendor ID
Model Description
Vari-lite
0x564C
Profile light engine TCW
Vari-lite
0x564C
Profile light engine TWW
Product Category 0x0101 0x0101
The table on the following pages outlines and describes all the RDM parameters IDs associated with the.
22
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
GET
SET
ALLOWED ALLOWED
RDM PARAMETER IDS
VALUE
COMMENT
ESTA STANDARD
REQUIRED /
DMX / UI DESCIPTION
Category – network Management
DIsC_UnIQUe_BranCH
0x0001
X
DIsC_MUTe
0x0002
X
DIsC_Un_MUTe
0x0003
X
X
PrOXIeD_DeVICes
0x0010
X
PrOXIeD_DeVICes_COUnT 0x0011
X
X
COMMs_sTaTUs
0x0015
Category – status Collection
X
QUeUeD_MessaGe
0x0020
X
sTaTUs_MessaGes
0x0030
X
sTaTUs_ID_DesCrIPTIOn 0x0031
X
Clear_sTaTUs_ID
0x0032
X
X
sUB_DeVICesTaTUs
0x0033
rePOrT_THresHOlD
Category – rDM Information
X
sUPPOrTeD_ParaMeTers 0x0050
X
X
ParaMeTer_DesCrIPTIOn 0x0051
X
Category – Product Information
X
DeVICe_InFO
0x0060
X
X
PrODUCT_DeTaIl_ID_lIsT 0x0070
X
DeVICeMODel
0x0080
DesCrIPTIOn
X
ManUFaCTUrer_laBel 0x0081
X
X
DeVICe_laBel
0x0082
X
X
FaCTOrY_DeFaUlTs
0x0090
X
lanGUaGe_CaPaBIlITIes 0x00a0
X
X
lanGUaGe
0x00B0
X
sOFTWareVersIOn
0x00C0
X
laBel
X
BOOTsOFTWare
0x00C1
VersIOn_ID
X
BOOTsOFTWare
0x00C2
VersIOn_laBel
Category – DMX512 setup
X
X
DMX_PersOnalITY
0x00e0
X
DMXPersOnalITY DesCrIPTIOn
0x00e1
X
X
DMX_sTarT_aDDress
0x00F0
X
X
slOT_InFO
0x0120
X
slOT_DesCrIPTIOn
0x0121
X
DeFaUlT_slOT_ValUe
0x0122
Category sensors 0x02xx Use
X
sensOr_DeFInITIOn
0x0200
X
X
sensOr_ValUe
0x0201
Fan speed and
X
reCOrD_sensOrs
0x0202
Category – Dimmer settings 0x03xx – FUTUre Use
X
X
Dimmer Curve
0x0343
X X X
X
status
X
X X
X
X
X
X
X
reset Defaults
X
Version
X
DMX Mode
X
X
address
X
X
X
X
X
Diagnostics
X
23
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
GET
SET
ALLOWED ALLOWED
RDM PARAMETER IDS
VALUE
COMMENT
ESTA STANDARD
REQUIRED /
DMX / UI DESCIPTION
X
Dimmer Curve Description 0x0344
X
X
Modulation Frequency
0x0347
X
Modulation Frequency Description
0x0348
Category – Power / lamp settings 0x04xx
X
X
DeVICe_HOUrs
0x0400
X
X
laMP_HOUrs
0x0401
X
X
laMP_sTrIKes
0x0402
X
X
laMP_sTaTe
0x0403
X
X
laMP_On_MODe
0x0404
X
X
DeVICe_POWer_CYCles 0x0405
Category – Display settings 0x05xx
X
X
DIsPlaY_InVerT
0x0500
X
X
DIsPlaY_leVel
0x0501
Category – Configuration 0x06xx
X
X
Pan_InVerT
0x0600
X
X
TIlT_InVerT
0x0601
X
X
Pan_TIlT_sWaP
0x0602
X
X
real_TIMe_ClOCK
0x0603
Category – Control 0x10xx
X
X
IDenTIFY_DeVICe
0x1000
X
X
reseT_DeVICe
0x1001
X
X
POWer_sTaTe
0x1010
all Test,
X
X
PerFOrM_selFTesT
0x1020 Pan/Tilt,
encoder
X
selF_TesT_DesCrIPTIOn 0x1021
X
CaPTUre PreseT
0x1030
see e120_2010a
X
X
PreseT PlaYBaCK
0x1031
Table a-7 defines
esTa reserved Future rDM
0x7Fe00x7FFF
Manufacturer-specific PIDs
0x80000xFFDF
Value range
depends
X
X
Output Power Mode
0x8a97 on options
(standard,
studio, etc)
X
X
Pan/Tilt Feedback (On/Off) 0x8aD3
X
X
Display On Time
0x8aa0
Value range depends on options
Value range
X
X
leD Dimmer Curve
0x8aa1 depends on
options
X
X
Pan Tilt Movement (On/Off) 0x8aa2
X
X
Head Motor Movement (On/ Off )
0x8aa3
X X X
X
Fixture Hours
X X
leD Output Mode X
Display On
X
Time
leD Dimming Curve
24
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
GET
SET
ALLOWED ALLOWED
RDM PARAMETER IDS
VALUE
COMMENT
ESTA STANDARD
REQUIRED /
DMX / UI DESCIPTION
Value range
X
X
auto shutdown Mode
0x8aa4 depends on
options
X
X
leD Hours
0x8aa5
X
X
Dim snap (On/Off)
0x8aa6
X
X
Color snap (On/Off)
0x8aa7
X
X
auto Fan Mode (On/Off)
0x8aa8
X
X
Gamma shift
0x8aa9
Value range depends on options
X
X
Tungsten Dimming (On/ Off )
0x8aaa
X
X
CTB Correction (On/Off)
0x8aaB
X
X
leD refresh rate
0x8aaC
Value range depends on options
X
X
side Hang (On/Off)
0x8aaD
X
X
Focus Track (On/Off)
0x8aae
X
Control signel select DMX only/artneT (On/Off)
0x8aaF
different
X
recalibrate Fixture (level)
0x8aB0
levels (all, position,
color, etc)
X
X
DMX Fail (Hold, Blackout, GOTO Preset)
0x8aB1
X
X
artnet Universe
0x8aB2
X
X
artnet net
0x8aB3
X
X
artnet sub-net
0x8aB4
X
X
artnet ethernet IP
0x8aB5
X
X
artnet ethernet sub-net Mask
0x8aB6
X
X
Manual PreseT Playback Power Up Preset
0x8aB7
X
X
Manual PreseT Playback Preset Intensity
0x8aB8
X
X
Manual PreseT Playback Priority
0x8aB9
X
X
Manual PreseT Playback Power Up?
0x8aBa
X
X
leD Color Calibration (On/ Off )
0x8aBB
leD Fan Mode
leD refresh rate
DMX Fail
leD Color
X
Calibration
25
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
APPENDIX A
Care anD MaInTenanCe
TROUBLESHOOTING
The following are a few common problems that may occur during operation.
Luminaire does not work; light and fan do not turn on. · Check power
connection and main fuse. · Measure the mains voltage on the main connector.
Not responding to DMX controller. · If DMX LED is not illuminated, verify that
the DMX cables are properly connected. · If the DMX LED is illuminated and
there is no response, verify DMX address settings and the DMX polarity. · If
you experience intermittent DMX signal problems, check the pins on the
connectors or on the PCB. · Test with a different DMX controller. · Check if
the DMX cables run near or alongside high voltage cables that may cause
interference to the DMX interface circuit.
CLEANING
Cleaning the inside of the luminaire must be carried out periodically in order
to optimize the light output.Cleaning frequency depends on the environment in
which the fixture operates. Damp, smoky or particularly dusty surroundings can
cause greater accumulation of dirt on the fixture’s optics.
· Clean with a soft cloth using glass cleaning fluid.
· Dry parts carefully.
· Clean the external optics at least every 30 days.
26
W W W.VA R I – L I T E .C O M
PROFILE LIGHT ENGINE TCW/TWW
USER MANUAL
APPENDIX B
FAN SPEED AND CONTROL
ADDENDUM
FAN SPEED AND CONTROL
All Vari-Lite luminaires will be governed by the same fan speed vs. noise
levels. vs. maximum power output rules as detailed below. The noise related to
these levels will conform to the Noise Criteria levels, details of which are
contained within this document.
There are three control parameters that can be selected separately or in
conjunction (when permitted) to manage fan speed vs. noise levels vs. maximum
power output.
NOTE: Not all fixtures have all modes or functions. Refer to DMX map and User
Interface menu tree to see if your product has one or more of these functions.
Output Modes
These modes are selectable at the fixture’s DMX control channel or via the
fixture’s user interface screen.
Boost mode – LED output boosted to >100% of standard output. Fan speeds
increased to manage heat level of LED (may be limited to only run for XX
hours). Fixture will not exceed NC45-NC55 sound levels in this mode.
Standard mode – Full LED output. Fan speed is set to cool LED appropriately
but not exceed NC40 sound level in this mode.
Studio mode – Fan speed reduced to achieve 10% dB reduction from Standard mode
and not exceed NC35 sound level. LED output is approximately 80% of Standard
output to ensure LEDs operate at optimum temperature and output efficiency.
Fan speed remains constant and does not ramp up or down.
Whisper mode – Fan speed reduced to achieve 30% dB reduction from Standard
mode and not exceed NC25 sound level. LED output is approximately 60% of
Standard output to ensure LEDs operate at optimum temperature and output
efficiency. Fan speed remains constant and does not ramp up or down.
Silent mode – fans are turned off or turn very slowly to not contribute to
fixture
noise. LED output is capped to ensure LEDs operate at optimum temperature
and output efficiency. Fans are either off or fan speed remains constant.
Target
NC15 sound level in this mode.
SOUND PRESSURE LEVEL (dB)
90
80
70 NC 55
NC 55 60
NC 55
NC 55 50
NC 50
NC 45 40
NC 40
NC 35 30
NC 30
20
NC 25
NC 20
10
NC 15
0 63
125 250 500 1000 2000 4000 8000 FREQUENCY (HZ)
MODE Boost Mode standard Mode studio Mode
Whisper Mode silent Mode
LED OUTPUT >100%
Full 100% 80%
60% TBC
FAN SPEED
Boosted fan speed constant Full 100% constant
appropriate speed to reduce dB levels >10% of full speed
appropriate speed to reduce dB levels >30% of full speed Fan off
NOISE CRITERION nC45 nC40 nC35
nC25 NC15
EQUIVALENT SOUND LEVEL DBA (@3M) 50 45
40
35
25
NOISE CRITERION
63
NC-15
47
NC-20
51
NC-25
54
NC-30
57
NC-35
60
NC-40
64
NC-45
67
NC-50
71
NC-55
74
NC-60
77
NC-65
80
NC-70
83
OCTAVE BAND CENTER FREQUENCY (HZ)
125
250
500
1000
2000
4000
8000
SOUND PRESSURE LEVELS (DB)
36
29
22
17
14
12
11
40
33
26
22
19
17
16
44
37
31
27
24
22
21
48
41
35
31
29
28
27
52
45
40
36
34
33
32
56
50
45
41
39
38
37
60
54
49
46
44
43
42
64
58
54
51
49
48
47
67
62
58
56
54
53
52
71
67
63
61
59
58
57
75
71
68
66
64
63
62
79
75
72
71
70
69
68
vls_adm_fan-tk-jan
27
W W W.VA R I – L I T E .C O M
TECHNICAL SUPPORT
GlOBal 24Hr TeCHnICal sUPPOrT:
Call: +1 214 647 7880 entertainment.service@signify.com
nOrTH aMerICa sUPPOrT:
Call: 877-VARI-LITE (877-827-4583)
entertainment.service@signify.com
eUrOPean CUsTOMer serVICe CenTer:
Call: +31 (0) 543 542 531 entertainment.europe@signify.com
©2024 Signify Holding. All rights reserved. All trademarks are owned by
Signify Holding or their respective owners. The information provided herein is
subject to change, without notice. Signify does not give any representation or
warranty as to the accuracy or completeness of the information included herein
and shall not be liable for any action in reliance thereon. The information
presented in this document is not intended as any commercial offer and does
not form part of any quotation or contract, unless otherwise agreed by
Signify. Data subject to change.
PROFILE LIGHT ENGINE TCW/TWW USER MANUAL VERSION DATE: MARCH 14, 2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>