REM01 Flex VRA Remote Control User Manual

REM01 Flex VRA Remote Control

About this guide

This guide explains the setup and operation of the Flex VRA remote control, P/N Flex-Remote-1.

Package Contents

The package contains the remote and the USB receiver.

Overview

• Flex wireless remote control is a single-frequency remote that transmits a 433.92 MHz (FSK) signal to Visual Reinforcement Audiometry (VRA) system.

Flex VRA System Operation

Pairing the Remote

• To pair the remote control with the USB receiver:
  • Press and Hold the Light On Button (3) and Lights Only Button (8) for 3 seconds.
  • The red Feedback LED turns ON and flashes.
  • Press the pairing button on the USB receiver once.
  • The Remote accepts the USB receiver pairing request.
  • Green Feedback LED blinks one time (slowly), turns OFF, and remote exits pairing mode.
  • The Remote is now paired to the USB receiver.

Un-Pairing Process

• Press and Hold the Light On Button (3) and Custom Button (9) for 3 seconds.
• RED Feedback LED turns ON.
• RED feedback LED blinks 5 times (slowly).
• Remote is now un-paired to the USB receiver.

Button Assignments

Normal Use – Remote Paired

• The user pushes a button on the remote.
  • THE GREEN LED on the remote blinks for the duration of the button being held down.
  • Attempted Use – Remote Not Paired
• The user pushes a button on the remote.
  • The RED LED on the remote blinks while the button is held down, but no signal is received by the USB receiver.

Replacing the Battery

• This remote needs a battery to operate.
• Replace the battery when needed with 2 AAA batteries.

To replace the battery:

• Pull the battery compartment out and remove the old batteries.
• Insert the replacement batteries.
• Close the battery compartment.
• If necessary, perform the pairing procedure.

FCC

Regulatory Compliance Statements FCC Compliance Statement

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions :

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• FCC ID: YI5-REM01

Industry Canada Statement

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

IC: 9065A-REM01

MORE INFO

• Flex VRA
• 100 E. Whitestone Blvd.
• St. 148, #160
• Cedar Park, TX 78613
• flexvra.com.
• Model: Flex-Remote-1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>