LP Aventure 2024 Plus Bumper Guard Installation Guide

: August 28, 2024
: LP Aventure

Table of Contents

LP Aventure 2024 Plus Bumper Guard
Specifications:
Product Usage Instructions
FAQ
IN THE BAG
NECESSARY TOOLS
INSTALLATION INSTRUCTION
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LP Aventure 2024 Plus Bumper Guard

Specifications:

Product: LP Aventure Bumper Guard
Compatibility: Subaru Crosstrek Wilderness 2024+
Tools Required for Installation: Ratchet, 19mm socket, 25mm socket, 14mm socket, 12mm socket, Push pin removal tool, 14mm wrench, 22mm wrench, Drill, 1 1/4 hole saw, Small flat screwdriver

Product Usage Instructions

Remove Push Pins

Remove the 4 push pins at each corner of the bumper using a push pin removal tool.

Prepare Bumper

Cut back the plastic to provide access for the bumper guard support rods. If already cut during R&D process, skip this step.

Drill Hole

Using a hole saw, drill a hole in the plastic right behind the bumper.

Install Bumper Guard

Put back the push pins.
Remove the tow hook covers.
Place the included spacer in front of the two hook threads.
Angle the support rod outward and insert it from the bottom aligning it in front of the tow hook hole.
Thread the included tow hook extension into the tow hook receiver but do not fully tighten yet.
Thread the nut on top of the bumper guard support rod to about 7/8 from the top.
Lift the bumper guard into place with assistance.
Thread the nut onto the end of the support rod.
Insert the bolt into the lower mounting location and thread the nut on without fully tightening.
Ensure the bumper guard is centered and all gaps are equal.
Fully tighten all hardware.
Put back the tow hook covers.

FAQ

Q : Where can I find product warnings?
A: Product warnings can be found here.
Q: Is there a limited product warranty?
A: Yes, you can find information about the limited product warranty here.

IN THE BAG

THE BARE BUMPER GUARD SHIPS WITH THE FRONT PLATE UNINSTALLED

NECESSARY TOOLS

Ratchet,
19mm socket
1″/25mm socket
14mm socket
12mm socket
Push pin removal tool
14mm wrench
22mm wrench
Drill
1″” 1/4 hole saw
Small flat screwdriver

INSTALLATION INSTRUCTION

REMOVE THE 4 PUSH PINS AT EACH CORNER OF THE BUMPER
USING A KNIFE, CUT BACK THE PLASTIC TO PROVIDE ACCESS FOR THE BUMPER GUARD SUPPORT RODS OURS WAS ALREADY CUT DURING THE R&D PROCESS
USING A HOLE SAW, DRILL A HOLE IN THE PLASTIC THA T IS RIGHT BEHIND THE BUMPER
PUT BACK THE PUSH PINS
REMOVE THE TOW HOOK COVERS
PLACE THE INCLUDED SPACER IN FRONT OF THE TOW HOOK THREADS
WITH THE SUPPORT ROD ANGLED OUTWARD, INSERT IT FROM THE BOTTOM AND ALIGN IT IN FRONT OF THE TOW HOOK HOLE
THREAD THE INCLUDED TOW HOOD EXTENSION INTO THE TWO-HOOK RECEIVER
THREAD THE NUT ON TOP OF THE BUMPER GUARD SUPPORT ROD TO ABOUT 7/8″ FROM THE TOP
LIFT THE BUMPER GUARD INTO PLACE. WE RECOMMEND EITHER THE HELP OF A FRIEND OR SOMETHING TO SUPPORT IT
THREAD NUT ONTO THE END OF THE SUPPORT ROD
INSERT THE BOLT INTO THE LOWER MOUNTING LOCATION
AND THREAD THE NUT ON
DO NOT FULLY TIGHTEN YET
MAKE SURE THE BUMPER GUARD IS CENTERED AND THAT ALL THE GAPS ARE EQUAL.
YOU CAN NOW FULLY TIGHTEN ALL THE HARDWARE
PUT BACK THE TOW HOOK COVERS

INSTALLATION COMPLETE

CONTACT

You have completed the installation. Thank you for your interest in our products. For all requests, information, or assistance: Contact our team by phone at