Amantii CUBE-2025WM TruView Cube Electric Fireplace with Speaker Base Instruction Manual

Amantii CUBE-2025WM TruView Cube Electric Fireplace with Speaker Base

IMPORTANT INSTRUCTIONS

1. Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury.
2. Keep combustible materials such as furniture, pillows, bedding, clothing, curtains and paper at least 3 ft from the front, sides and rear of the heater.
3. Always unplug heater when not in use.
4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the unit has been dropped or damaged in any way.
5. Never place the heater where it may fall into a bathtub or other water container.
6. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.
7. To disconnect the heater, turn the controls to “OFF” before removing the plug from the outlet.
8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.
9. To prevent a possible fire, do not block air intakes.
10. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
11. Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
12. Always use properly grounded fused and polarized outlets.
13. Always use ground fault protection where it is required by electrical codes.
14. Always disconnect the power before performing any cleaning, maintenance or relocation of the heater.
15. To prevent a possible fire, do not burn wood or other materials in this heater.
16. To prevent electric shock or fire, always use a certified electrician, should new circuits or outlets be required.
17. When transporting or storing the heater, keep it in a dry place, free from excessive vibration.
18. This appliance should not be modified under any circumstances.
19. Keep the packaging material out of reach of children and dispose of the  material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.
20. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
21. If the glass is damaged, do not use the heater in order to avoid a hazard.
22. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house.
23. CAUTION Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly.
As with most electronic devices ℉ , your new ℃ electric fireplace has been designed to operate at temperatures between 5 (41 ) and 35 (95 ). During the cold winter months, allow the fireplace to reach room temperature before turning it on

NOTE: There may be trace of odor during the first few minutes of initial use. This is harmless, normal and will never occur again.

GROUNDING APPLIANCE

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. To disconnect appliance, turn controls to off, then remove plug from outlet

LOCATING THE FIREPLACE

Plan where to locate and frame the fireplace. This will save time and money later when you install the fireplace. Before installation consider the following:

1. Where the fireplace is located must allow for wall and ceiling clearances.
2. Consider a location where the fireplace screen will not be exposed to  direct sunlight from windows or doors.
3. A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers to trip of fuses to blow.

CUBE-2025WM

This appliance has been tested in accordance with the UL Standard 2021 for fixed and location dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer

NOTE: This appliance must be electrically wired and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70 National Electrical Code in the United States.

INSTALLATION WALL-MOUNT

NOTE : Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance.

1. Select a location that is not prone to moisture and is located at least 0.91 m or 3 feet away from combustible materials such as curtains or drapes, furniture, bedding, paper, etc

2. Select a suitable position in whic the heater horizontally – use a spirit level to achieve this (Fig. 1).

3. Check the wall to ensure there is no wiring, pipe wires etc. in the area to be drilled. Drill 8 or more pilot holes (8mm diameter & 40mm depth) using a suitable size drill a put the wall plugs into the holes

4. Take out the hanger from the fireplace by unscrew the screw (Fig.2).

5. Fix the hanger to the wall. Referring to Fig. 3

6. Avoid fireplace to move, use screw fix fireplace to wall (Fig. 4).

INSTALLATION CUBE-BASE-LEGS

1. Screw the base legs to the steel panel.

2. Unscrew the adjustable feet from the bottom of the unit.
   

3. Place the unit onto the base leg in the adjustable feet, fixing the unit and the base leg.
   

4. You have completed the CUBE-BASE-LEGS.
   

INSTALLATION CUBE-BASE-SPEAKER

1.  Unscrew the adjustable feet from the unit.

2. Unscrew the rear screws and remove the back steel panel.

3. Place the unit on the CUBE-BASE-SPEAKER and screw in the adjustable feet, fixing the unit and the speaker box.
   

4. Plug into the back of the unit. Re-install the back steel panel.

INSTALLATION OUTDOOR

CUBE electric fireplaces are suitable for installation in outdoor areas protected from direct water impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed appliance. See illustration below. All wiring connections to line power shall be in accordance with local building code requirements.

NOTE: The CUBE Wall Mount Unit is approved for outdoor use. The Cube Speaker Base and Cube Leg Base are NOT approved for use outdoors.

The overhang (A) must extend at least 1/2 the roof-line height (B). Height is measured from the base of the fireplace.
For example: if the roof-line (B) is 8′ above the base of the fireplace, the overhang (A) must be at least 4′

HARD- WIRE INSTALLATION

Turn off the appliance completely and let cool before servicing. Only a qualified technician should service and repair this electric appliance.
If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

1. Remove the cover plate from the left side of the appliance by removing the two screws, as shown below. Unscrew and remove power cord
   

2. Attach the wiring to the junction block. Pl neutral wire into “N” and the ground wire into “G”
   

3. Replace the steel plate and screws.

MEDIA OPTIONS

Your fireplace shipped with DESIGNMEDIA-BIRCH-10PCE.

DESIGN-MEDIA-BIRCH-10PCE

MEDIA INSTALLATION

STEP 1 : Unplug the unit and make sure controls are switched off.

STEP 2 : Unscrew 2 adjustable screws that securing the front glass panel. (Always secure the front glass before unscrewing the securing screws, removal of the securing screws may cause the front glass to fall out suddenly)

STEP 3 : Remove the front glass panel to decorate your fireplace. Pour the decorative media into the tray. Feel free to use any combination of fire glass media that you find most appealing.

STEP 4 : After finishing decoration, re-install the front glass panel using the securing screws removed in step 2.

OPERATION

The fireplace can be operated either by the switches located on the left front of the fireplace unit or by supplied remote control.

MANUAL OPERATION

1. The main power ON/OFF switch in position 0, the fireplace is OFF. 2

2. When main power ON/OFF switch is at position I, the fireplace is ready to use.

3. Press the button repeatedly to set the heater to desired heat setting. The heater indicator LED will glow which shows the current heater settings.
   a) RED1465WHEATOUTPUT
   b) BLUE 750W HEAT OUTPUT
   c) PURPLE AUTO MODE
   AUTO MODE
   Under this mode the heater will automaticallyturn ON at high heat setting 1465W heat output whithe room temperature drops below 22 CC (72°F ). When the room temperature is between 22- 25 CC (72-77°F ) the heater output will switch to low heat setting 750W. When the room temperature goes above 25 °C (77°F ) the heater will be turned off and the cycle will continue. The LED indicator will be PURPLE in colour under this mode.

4. Flame effect: Press the button marked to adjust the flame brightness. The flame brightness will cycle through -Low-Medium-High -OFF

5. Mood light effect: Press the button marked to change the mood light colour.

NOTE : If operated at the Low heat setting, the fireplace will not provide as much heat output as in the High heat setting, however the low setting will not require as much electrical power to operate. To avoid overloading a circuit, do not plug the fireplace into a circuit that already has other appliances working. When the fireplace is not in use switch off and unplug.

SAFETY CUT-OFF

• This appliance is fitted with a safety cut-off which will operate if the fireplace overheats (eg. Due to blocked air vents). For safety reasons, the fireplace will NOT automatically reset.
• To reset the appliance, disconnect the appliance from the main supply for at least 10 minutes. Reconnect the supply to the main and switch on the appliance.

REMOTE CONTROL OPERATION

For remote to function make sure the heater is plugged in and main power switch located on the bottom left hand side is at position I.
When operating the remote make sure you point the remote to the center of the fireplace and make sure each time you press the button the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter. Do not PRESS the buttons more than once within two seconds for correct operation

Power on button: The power-on button at top left corner of the remote is the main ON/OFF
power button. This will turn off all the functions and the fireplace will be in standby mode

DISPLAY ON/OFF button : Switching the fireplace flame and tray light ON/OFF. It has functions of setting memory.

DISPLAY BLUE button: Adjust the blue color brightness of flame and tray.
DISPLAY YELLOW button : Adjust the yellow color brightness of flame and tray.
DISPLAY ORANGE button : Adjust the orange color brightness of flame and tray.

MOOD LIGHT ON/OFF button: Switching the mood light ON/OFF.
ADJUST button: Switching the color of the mood light.
FLASH button: Switches the mood light into flash mode, this cycles through all mood light colors

HEATER ON/OFF button: Switching the heater ON/OFF. It has functions of setting memory.
HIGH button: Press the high button to switch the heater to high heat setting 1465W.
LOW button: Press the low button to switch the heater to low heat setting 750W.
TEMP. button: Press the TEMP. button to switch the heater to AUTO mode. Under this mode the heater will operate in similar way as explained above for the manual operation.

INSTALLING WALL THERMOSTAT

WALL THERMOSTAT WIRING DIAGRAMS

Wire the wall thermostat prior to installing the fireplace. WALL THERMOSTAT WIRING {24 VAC)

Install Wall Thermostat per instructions provided with kit and per the following information

1. Turn off circuit breaker.
2. Remove cover plate located on the left side of appliance.
3. Pull the wire out and cut the inside thermostat. Connect the wires to the wall thermostat as shown below. Follow instructions provided with wall switch kit
   |
   ---|---
   |

REPLACEMENT PARTS

This list contains replacement parts

NO.

|

PART NUMBER

|

DESCRIPTION

|

QTY.

---|---|---|---
1| 10701357| FRONT CLEAR GLASS (MIDDLE)| 1
2| 10201505| ADJUSTABLE SCREW| 2
3| 3123010| FIXER FOR FRONT GLASS PANEL| 1
4| 10701356| SIDE GLASS PANEL| 2
5| 10702216| VISUAL GLASS| 1
6| 10702215| BOTTOM GLASS| 1
7| 602082| BLOWER AND HEATER ASSEMBLY| 1
8| 601036| CONTROL PANEL| 1
9| 10104002| SWITCH| 1
10| 3158501| FIRE BOX| 1
11| 601097B| CIRCUIT BOARD| 1
12| 301506| REMOTE RECEIVER| 1
13| 10101225| FLAME MOTOR| 1
14| 3173502| FLICKER ASSEMBLY| 1
15| 601136B| LED STRIP| 1
15| 601141B| LED STRIP| 1
16| 10105063| REMOTE CONTROL| 1
17| 10125025| TOP LIGHT| 1

*Remote control and top light are not shown in the exploded view.

EXPLODED VIEW

TROUBLE SHOOTING

them if necessary.
Back black cloth is falling off and rolled up in the flicker.| Change a flicker and back black cloth.
Ember bed  is  not glowing or dimming| Ember LED’s are burnt out| Inspect the ember bed LED’s and replace them if necessary.
Appliance turns off and will not turn on| Appliance has overheated, and safety device has caused the thermal switch to disconnect.| Turn off the main switch, allow appliance to cool for 10 minutes, turn back on.
House circuit breaker has tripped.| Reset house circuit breaker.
Appliance’s fuse has blown.| Replace the fuse.
Appliance will not come on when switch is flipped to ON| Appliance is not plugged into an electrical outlet.| Check plug and plug in.
Appliance has overheated and safety device has caused the

thermal switch to disconnect.

| Turn off  the main switch, allow appliance to cool for 10 minutes, turn back on.
Circuit board is burnt out.| Inspect the circuit board and replace it if necessary.
No warm air coming out

of appliance

| Heater is burnt out.| Inspect  the burner and heater assembly and replace it if necessary.
Flame sputters| Flame motor is defective.| Call a qualified service technician and replace flame motor.
Remote Control does not work.| Low batteries.
Unit switch in “O” position.| Replace AAA batteries in remote control. Turn the switch in “I” position.
Flame is fixed.| Wiring may be loose or the flame motor may be defective.|

WARRANTY FOR PRODUCTS MANUFACTURED AFTER JANUARY 1st, 2016

Amantii Imports Corp. (“Amantii “) warrants that your newly purchased Amantii electric fireplace is free from manufacturing and material defects for a period of two (2) years from the date of the first purchase, subject to the conditions and limitations contained below.

Warranty Application & Exclusions

This limited warranty applies to your newly purchased Amantii electric fireplace; the limited warranty’s application is limited to purchases made in any province of Canada or in any of the 52 States of the United States of America, including the District of Columbia. Only the original purchaser of the product is eligible for coverage under this limited warranty; the warranty is not transferable.

Products excluded from this limited warranty

Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/ purchaser. Amantii does not cover service or labor charges.

Warranty Coverage and Term

Products covered by this limited warranty have been tested and inspected prior to shipment and , subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of two (2) years from the date of the first purchase of such products.
The limited two (2) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser.

All other warranties-expressed or implied-with respect to the product, its components and accessories or any obligation/liabilities on the part of Amantii are hereby expressly excluded.

Limitations to Coverage Under Limited Warranty

This limited warranty does not apply to products that have been repaired, except by Amantii or its authorized service representatives, or otherwise altered. This limited warranty further does not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source. Products made by other manufacturers, sold with the product or thereafter, are not covered by this limited warranty. The use of unauthorized components will render this warranty null and void.

Panorama Outdoor Units

All Panorama units that are installed outdoors or in moisture intense conditions must use the stainless steel cover. Proof of purchase of the cover is required for any warranty claims.

Defects

Defects must be brought to the attention of the selling dealer. Please have your proof of purchase, catalogue/model and serial numbers available when contacting dealer; any and all service under the limited warranty requires a proof of purchase of the product. Should a product or part covered by this limited warranty be proven to be defective, in material or workmanship, and during the two (2) year limited warranty period, Amantii will replace such defective product or part without charge. If Amantii is unable to replace such product, or if replacement is not commercially practicable or cannot be timely done, in its sole discretion Amantii may, in lieu of replacement, choose to refund the purchase price for such product or part. Amantii does not cover labor or service charges to replace said parts.

Limitations

In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, be liable to the purchaser or any third party, whether in contract, in tort, or on any other basis for any indirect , special, punitive, exemplary, consequential , or incidental loss, cost or damage arising out of or in connection with the sale, maintenance, use or inability to use the product, even if Amantii, including without limitation any of its directors, officers, shareholders, employees, consultant s, agents, heirs, executors, administrators and assigns, have been advised of the possibility of such losses, costs or damages, or if such losses, costs or damages are foreseeable. In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, be liable for any direct losses, costs or damages that exceed the purchase price of the product.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the purchaser.

Application of Provincial and State Law

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

General

Amantii reserves the right to make changes at any time without notice, in design, material, specifications, prices and the right to discontinue styles and products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>