Taiko Audio TAP140 High End Music Servers User Guide
- August 27, 2024
- TAIKO AUDIO
Table of Contents
Migrate Storage Guide
MacOS
Important Notes
Please note that the Olympus Server does not have an RJ45 network connection,
only an SFP port. To allow connecting a standard RJ45 ethernet cable from your
home network to enable the music copying process, we supply an RJ45 to SFP
Adapter. RJ45 is the connector that all regular Ethernet cables use. You can
use any common Ethernet cable variant (CAT5, CAT6, CAT7, CAT8) for music
library migration.
For customers of the Taiko Extreme Router:
The Taiko Router is designed to create an audio only network and deliberately
limits the interaction with non-audio related downstream components.
Additionally, it is optimized for minimal noise and low power consumption, not
for the highest data transmission speed. Therefore, Taiko advises to not use
the Taiko Router for the task of music library migration, but to use your home
router instead. After the data transfer is done, connect the Taiko Router into
the chain again.
Music Library
In the past, when buying a new source, you did not have to worry about your
music collection, as that would stay in your home as physical purchased media.
With music servers, your music collection is made up of files that are
normally stored on an internal drive of your existing music server.
These files need to be transferred to a new location prior to parting ways
with the old server.
Depending on your desired storage location and whether the two servers are
available at the same time, there are three scenarios for transferring your
music:
- Temporarily keeping your old music server
- Keeping a copy of your music files on an additional drive
- Storing your music files on a NAS
Temporarily keeping your old music server
If you can keep your existing server operational and connected to the network
until the new server arrives, you can transfer the music library directly from
the old server to the new server using the standard Samba protocol via your
local network.
For the highest speed and best performance for music transfer, do not use the
Taiko Extreme Router, but use your home router instead. Make sure to connect
both servers as well as your Mac to the home network.
Important
Please note that the Olympus Server does not have an RJ45 network connection,
only an SFP port. To allow connecting a standard RJ45 ethernet cable from your
home network to enable the music copy process, we supply an RJ45 to SFP
Adapter. If you have the Extreme Router, please reconnect it once the copy
process has been completed.
Quick start
On your Mac, open one Finder window by using the keyboard combination Cmd-N to
your old music server’s music drive and a second Finder window to the new
server’s music drive, as follows.
Window 1:
\\OLDserver IP-address
Window 2:
\\NEWserver IP-address
Then, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
Detailed steps
You can find both your servers’ IP addresses by using a network scanner app on
your phone or Mac. We recommend Fing, which is available for iOS, iPadOS, and
MacOS hardware containing the M1 processor or later.
To access the old server, first click on the desktop or on the Finder icon in
the Dock to select the Finder, then click the “Go” item in the top menu and
click “Connect to Server.
This brings up a popup window.
Enter your old server’s IP address, in prepended with “smb://”, for example:
smb://192.168.178.214
Alternatively, if your old server is the Extreme, you can also access it by using its name and your unique serial number, prepended with “smb://”, for example: smb://extreme12345 (substitute 12345 with your own serial number) Click “Connect”.
If prompted for credentials to access the Extreme’s Music Share, use the
following for Extreme:
Username: Administrator
Password: SoundTest
This will produce a new popup window showing the contents of your old server.
For the Extreme, select “Music”, and click “OK”.
A window will appear with the contents of your old server’s Music driver.
Position it to the left of your screen. This is now considered window 1.
Open a second Finder window using key combination Cmd-N.
Postition this window on the right of the screen. This is now considered window 2.
For the second Finder window, repeat the steps to access the new Olympus
server.
Please note that the Olympus credentials are different!
If prompted for credentials to access the Olympus Music Share, use the
following:
Username: Olympus (Note that this is different from the Extreme Login)
Password: SoundTest
Next, select all your music files in window 1 by clicking on a clear/white
section and typing Cmd-A. Alternatively, click the “Edit” item in the top
menu, and click “Select All”.
Finally, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
Keeping a copy on an additional drive
If you will not have your old and new server available simultaneously, you can
use an external USB-connected drive to make a copy of your music collection.
If you don’t have a backup of your music library yet, this will also be the
ideal time to create one. After copying the music across, you will have a
backup and a drive from which to copy music to your new server.
For this scenario, connect the external drive to your Mac so that it mounts as
a local drive, and you can use the standard Samba protocol via your local
network to transfer the files.
Quick start
Open one Finder window by using the keyboard combination Cmd-N (Apple-N) to
your old music server and a second Finder window to the drive, as follows.
Window 1:
\\OLDserver IP-address\share name
Window 2:
\\Local drive location
Make sure your local drive has enough capacity to hold all your files. If it
contains files that you just deleted, make sure to also empty the trash.
Then, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
Detailed steps
You can find your old servers’ IP address by using a network scanner app on
your phone or Mac. We recommend Fing, which is available for iOS, iPadOS, and
MacOS hardware containing the M1 processor or later.
To access the old server, click the “Go” item in the top menu and click
“Connect to Server (to see “Go”, you need to first click either on the
Desktop, or alternatively on the Finder).
This brings up a popup window.
Enter your old server’s IP address, in prepended with “smb://”, for example:
smb://192.168.178.214
Alternatively, if your old server is the Extreme, you can also access it by
using its name and your unique serial number, prepended with “smb://”, for
example:
smb://extreme12345 (substitute 12345 with your own serial number) Click
“Connect”.
If prompted for credentials to access the Extreme’s Music Share, use the
following:
Username: Administrator Password: SoundTest
This will produce a new popup window showing the contents of your old server.
For the Extreme, select “Music”, and click “OK”.
A window will appear with the contents of your old server’s Music driver.
Position it to the left of your screen.
This is now considered window 1.
Now, connect your additional USB drive (SSD drive, HHD drive, or universal
dock) to your Mac so that it mounts as a local drive. Normally, the drive will
automatically appear on the desktop. Double-click it to open its contents in a
new Finder window and position it to the right of the first window.
If the drive does not appear on the desktop, locate the Hard Drive icon on
your desktop, usually labelled “Macintosh HD”, and double-click it. Then, look
in the sidebar to find your drive.
If you do not have any icons on your desktop, you can open a second Finder
window using key combination Cmd-N and locate the drive in the sidebar.
You should now have 2 windows side by side, one showing the contents of your
old server, and one showing the additional drive.
Delete any existing contents on the drive to obtain an empty window. Empty
your trash can, and check that your additional drive has enough storage to
contain all your music files.
Next, select all your music files in window 1 by clicking on a clear/white
section and typing Cmd-A. Alternatively, click the “Edit” item in the top
menu, and click “Select All”.
Finally, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
Storing your music files on a NAS
NAS stands for Network Attached Storage. Think of it as a Hard Drive with a
network connection, to which you can copy your existing music collection.
After copying your files to a NAS, you can use the NAS directly as a music
source with your new server – no additional copying required. But, if desired,
you may also use the NAS as transitional storage from which you will copy your
music to the new server later.
Copying your locally stored music to a NAS typically entails connecting the
NAS to the same network as your old server, Mac or Macbook, and new server,
and using the standard Samba protocol to access both servers via the network.
Quick start
On your Mac, open one Finder window to your old music server and a second
Finder window to the NAS, as follows.
Window 1:
\\OLDserver IP-address\sharename
Window 2:
\\NAS IP-address\sharename
Then, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
You can find your NAS and server IP addresses by using a network scanner app
on your phone or Mac. We recommend Fing, which is available for iOS, iPadOS,
and MacOS hardware containing the M1 processor or later.
Then, you simply drag and drop the contents of window 1 to window 2 to copy
the files across. Libraries up to ~6TB can be copied overnight, most of it
while you sleep.
Once your music collection is stored on a NAS, all you need to do is add the
following address as a storage location in the Roon – Settings – Storage, and
you’re done.
\\NAS IP-address\sharename
Detailed steps
You can find your old servers’ IP address by using a network scanner app on
your phone or Mac. We recommend Fing, which is available for iOS, iPadOS, and
MacOS hardware containing the M1 processor or later.
To access the old server, click the “Go” item in the top menu and click
“Connect to Server (to see “Go”, you need to first click either on the
Desktop, or alternatively on the Finder).
This brings up a popup window.
Enter your old server’s IP address, in prepended with “smb://”, for example:
smb://192.168.178.214
Alternatively, if your old server is the Extreme, you can also access it by using its name and your unique serial number, prepended with “smb://”, for example: smb://extreme12345 (substitute 12345 with your own serial number) Click “Connect”.
If prompted for credentials to access the Extreme’s Music Share, use the
following:
Username: Administrator
Password: SoundTest
This will produce a new popup window showing the contents of your old server.
For the Extreme, select “Music”, and click “OK”.
A window will appear with the contents of your old server’s Music driver.
Position it to the left of your screen.
This is now considered window 1.
Next, open a second Finder window for the NAS, using key combination CmdN, and
position it on the right of your screen. If your NAS has been used with this
Mac before and is already mounted, you can directly select it from the
sidebar. Otherwise, you need to connect to it first.
If your NAS is not visible, you will need to use Fing to find its IP address.
To connect to your NAS, click on the second Finder window you just opened to
make it active. Then, click the “Go” item in the top menu and click “Connect
to Server.
Enter the NAS’s IP address in the same manner as done with your old server for
window 1. If you cannot find your NAS, please refer to the manufacturer’s
instructions on how to mount and access it.
Once connected, you should now have 2 windows side by side, one showing the
contents of your old server, and one showing the NAS.
Navigate to your desired location on the NAS in window 2. We recommend storing
the music in the topmost folder of your NAS’s folder hierarchy. You may also
create a new folder named “Music”.
Next, select all your music files in window 1 by clicking on a clear/white
section and typing Cmd-A. Alternatively, click the “Edit” item in the top
menu, and click “Select All”.
Finally, drag and drop the selected contents of window 1 to an empty space in
window 2 to copy the files across.
Once your music collection is stored on a NAS, you need to add the NAS’s
address as a storage location in the Roon Settings. You can do this from your
Mac if you have Roon installed on it, or you may do it from the iPad or
iPhone.
We’ll show iPad screenshots below. To add the NAS storage to Roon, first tap
the hamburger menu on the top left to bring up the Sidebar.
Next, at the top of the sidebar, tap the “Gear Wheel” Settings Icon.
Next, first, tap “Storage” in the sidebar.
Then, tap “Add Folder” on the right.
In the popup window that appears, tap “Add Network Storage”, in the bottom left.
Finally, enter the NAS’ location, as follows: \\NAS ip-address\sharename
Then, optionally, enter the Username and Password you specified for the NAS.
If you did not create a user account, there may be a default user account.
Please see the documentation that came with your NAS for more information.
Tap the “Add network share” button, and you’re done!
The origins and benefits of NAS
Keeping your music collection on a NAS is how things started out in the early
era of music servers. Although online streaming services like Tidal or Qobuz
did not exist back then, network players were called streamers as they would
stream files from your NAS.
Over the years, in the pursuit of better sound quality, streamers turned into
music servers as companies started incorporating local storage devices for
improved performance. This is nowadays the norm.
With the launch of the Taiko Audio Extreme Router and the Olympus, and the
disappearance of the sound quality benefit of locally stored files, returning
to storing your music collection on a NAS has become a viable option again.
At Taiko HQ, we obtained stellar results with Synology and QNAP NAS, but any
competent NAS can be used.
The benefits of NAS-based storage libraries are:
- Improved safety/protection of your music collection.
- Not having to copy your music collection again if the internal drive of your music server fails or when moving to a different server.
- A NAS is an always online “remote” storage location on which you can store your Roon backups. Simply tell Roon to backup once a day, or once a week, to the NAS. If your music server fails, you can always restore from your NAS and retain all your settings and Roon playlists.
About this guide
The methods described describe the easiest ways to do transfer your music.
There is a faster method, but it is also more complex, requiring opening the
servers to swap drives, which requires more than basic computer operating
skills.
If you prefer the fastest method of transfer, or if the methods described seem
daunting, do not hesitate to ask your dealer for help. The transferal of a
music library is something you can expect your dealer to help with as part of
the after sales / installation service.
You may also ask your dealer for help or guidance when in doubt. Naturally,
you can also contact our support desk
(support@taikoaudio.com) if things remain
unclear, we’re here to help!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>