momax 1-VIBE GO Magnetic Bluetooth Speaker Instruction Manual
- August 26, 2024
- MOMAX
Table of Contents
Lomax 1-VIBE GO Magnetic Bluetooth Speaker
Product Overview
INSTRUCTION FOR USE
LEDLight Status (LED status)
Magnetic sheet installation steps
- Remove the anti-static film protective layer.
- Stick it on the back of the phone case.
- Smooth out the bubbles and make sure the anti-static film and phone case are firmly attached.
- Remove the magnetic sheet sticker and stick it on the protective film.
Phone models that support magnetic wireless charging natively may not require such a Magnetic sheet. Because the corresponding wireless charging position of each mobile phone model that supports wireless charging (non-native magnetic charging support) may be different, please consult the corresponding mobile phone brand to obtain such information.
SPECIFICATION
CONTAINS
- Magnetic Bluetooth speaker
- USB-A to USB-C Cable (30cm)
- Magnetic patch and protective film
- Instruction Manual and Warranty Card
WARNING
- Do not dismantle or modify the product;
- Do not store the product in wet conditions;
- Do not keep or use the product near heat sources;
- Do not let water or any other liquid flow into the inside part of the product’s interface. This would cause damage to the product;
- Make sure to remove the metallic or magnetic protective case of your device when charging;
- While charging, the 1-VIBE GO may heat up. This is normal and should not affect 1-VIBE GO performance.
- If the battery feels hot to the touch during this charging process, remove the 1-VIBE GO from the charger and allow it to cool down before restarting the charging process;
- Avoid using bent or damaged Ucablesble.
DISPOSAL OF ELECTRONIC PRODUCTS
- Do not place the product as household waste;
- Please dispose of discarded electronic products properly according to local regulations.
- MOMAX encourages you to participate in an electronics recycling program.
WARRANTY CONDITIONS
- For any defect, in the judgment of our technician, caused under normal use, we are responsible for repairing free of charge for 12 months commencing from the date of purchase at the discretion of our company;
- A valid warranty card and original purchase invoice must be presented upon request of warranty service;
- This warranty card shall not apply to the product if:
- it has explicitly modified or repaired in any way by persons other than technicians of this company, or
- it has been damaged through misuse, malicious acts, negligence, the inflow of any liquid, or
- losses or damages are caused by force majeure or natural disasters.
- No alteration to this warranty card will be allowed
- The warranty terms and conditions are subject to change without prior notice
- Please retain your proof of purchase for warranty service
- Please consult the dealer about the product compatibility with your cell phone PDA before purchase. Product specifications are subject to change without prior notice;
- Please visit www.momax.net for the latest product information.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2)this device must
accept any interference received, including interference that may cause
undesired operation Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communicationsHowever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for helpThe device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>