Shark AZ3000 Series Stratos DuoClean Powered Lift-Away with Odor Neutralizer Upright Vacuum User Manual
- June 9, 2024
- Shark
Table of Contents
- Shark AZ3000 Series Stratos DuoClean Powered Lift-Away with Odor
- IMPORTANT SAFETY INSTRUCTIONS
- ASSEMBLY
- TECHNOLOGY SETTINGS
- ODOR NEUTRALIZER TECHNOLOGY
- WHOLE-HOME CLEANING
- EMPTYING THE DUST CUP
- CLEANING AND REPLACING THE FILTERS
- MAINTENANCE
- CORD MAINTENANCE
- CHECKING FOR BLOCKAGES
- AVAILABLE ACCESSORIES
- TROUBLESHOOTING
- SHARK | NINJA
- FIVE (5) YEAR LIMITED WARRANTY
- REGISTER YOUR PURCHASE
- RECORD THIS INFORMATION
- TECHNICAL SPECIFICATIONS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Shark AZ3000 Series Stratos DuoClean Powered Lift-Away with Odor
Neutralizer Upright Vacuum User Manual
AZ3000 Series
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
WARNING
To reduce the risk of fire, electric shock, injury, or property damage, when
using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM
1. I nspect power cord and plug for any damage before use. DO NOT use vacuum
cleaner with a damaged cord or plug. Turn off all controls before plugging in
or unplugging the vacuum cleaner. Store your vacuum cleaner with the power
cord secured around the two cord hooks. To minimize
the risk of power cord damage, do not allow the motorized brush roll
to ingest the cord. If this occurs, immediately shut off power to the vacuum
and remove the cord.
2. T his appliance has a polarized plug. If the plug does not fit fully into
the outlet, reverse the plug (one blade is wider than the other). If it still
does not fit, contact a qualified electrician. DO NOT force into outlet or try
to modify to fit.
3. Y our vacuum cleaner may consist of a motorized nozzle, wand, hose, and/or
vacuum pod. This device contains electrical connections, electrical wiring,
and moving parts that potentially present risk to the user. The hose contains
electrical wires. Do not use when damaged, cut, or punctured.
4. U se only identical replacement parts.
5. Carefully observe and follow the instructions provided below to avoid
improper use of the appliance.
DO NOT use the vacuum for any purpose other than those described in this
manual.
6. Before use, carefully inspect all parts for any damage. DO NOT use if any
parts are damaged.
7. The use of an extension cord is NOT recommended.
8. T his vacuum cleaner contains no serviceable parts.
9. T his appliance can be used by persons with reduced physical, sensory, or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Cleaning and
user maintenance shall not be made by children. Keep the appliance and its
cord out of reach of children. DO NOT allow the appliance to be used by
children. DO NOT allow to be used as a toy. Close supervision is necessary
when used near children.
10. Always turn off the vacuum cleaner before connecting or disconnecting any
motorized nozzles, hose, or other accessories.
11. DO NOT handle plug or vacuum cleaner with wet hands.
12. DO NOT use without filters in place.
13. Only use Shark® branded filters and accessories.
14. DO NOT damage the power cord:
a) DO NOT pull or carry vacuumcleaner by the cord or use the cordas a handle.
b) DO NOT unplug by pulling on cord.
Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner over the power cord, close a door on the
cord, pull the cord around sharp corners, or leave the cord near heated
surfaces.
15. DO NOT put any objects into nozzle or accessory openings. DO NOT use with
any opening blocked; keep free of dust, lint, hair, and anything that may
reduce airflow.
16. DO NOT use if nozzle or accessory airflow is restricted. If the air paths
or the motorized floor nozzle become blocked, turn the vacuum cleaner off and
unplug from electrical outlet. Remove all obstructions before you plug in and
turn on the unit again.
17. Keep nozzle and all vacuum openings away from hair, face, fingers,
uncovered feet, or loose clothing.
18. DO NOT use if vacuum cleaner is not working as it should, or has been
dropped, damaged, left outdoors, or dropped into water.
19. Use extra care when cleaning on stairs.
20. DO NOT leave the vacuum cleaner unattended while plugged in.
21. When powered on, keep the vacuum cleaner moving over the carpet surface
at all times to avoid damaging the carpet fibers.
22. DO NOT place vacuum cleaner on unstable surfaces such as chairs or
tables.
23. Your Shark® vacuum may not be designed to stand up on its own. When
taking a break from cleaning, you may need to lean it against furniture or a
wall, or lay it flat on the floor. Using the vacuum for an application where
the unit lacks stability may result in personal injury.
24. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects (glass, nails, screws, or coins)
d) Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT
use as an attachment to power tools for dust collection.
e) Smoking or burning objects (hot coals, cigarette butts, or matches)
f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene)
g) Toxic materials (chlorine bleach, ammonia, or drain cleaner)
25. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may contain explosive or toxic fumes or vapors
(lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing
substances, or flammable dust).
26. Turn off all controls before plugging in or unplugging the vacuum.
27. Observe the following when interacting with the odor neutralizer
technology cartridge
a) DO NOT attempt to disassemble odor neutralizer technology cartridge.
b) Avoid direct contact with the fragrance pod in the cartridge.
c) DO NOT directly inhale from the odor neutralizer technology cartridge
d) Keep away from children and pets.
e) Keep away from heat, sparks, and open flame.
f) DO NOT place in direct sunlight.
FRAGRANCE CARTRIDGE FIRST AID
a) Avoid contact with fabrics and finished surfaces.
b) Eye contact: Remove contact lenses if present. Rinse continuously with
water for several minutes.
c) Skin contact: Wash hands thoroughly after handling. If irritation or rash
develops, seek medical advice/attention.
d) Inhalation: Move person to fresh air if they are experiencing any
respiratory symptoms. If symptoms persist, seek medical advice/attention.
e) Ingestion: DO NOT induce vomiting. Seek medical advice/attention.
28. Unplug from electrical outlet when not in use and before any maintenance
or cleaning.
29. Hand wash with water only.
Washing with cleaning chemicals could damage the unit.
30. During cleaning or routine maintenance, DO NOT cut anything other than
hair, fibers, or string wrapped around the brushroll.
31. Allow all filters to air-dry completely before replacing in the vacuum to
prevent liquid from being drawn into electric parts.
32. Make sure the dust cup and all filters are in place after routine
maintenance.
33. I f provided, secure the power cord around the two cord hooks during
storage.
“SAVE THESE INSTRUCTIONS”
ASSEMBLY
1. Place motorized Nozzle on floor and insert Wand, pressing it in until it
clicks
securely into place.
2. Place Pod onto wand and slide down to connect.
3. Insert Handle into wand, pressing it in until it clicks securely into
place.
4. Connect Hose to back of pod, pressing it in until it clicks securely into
place.
5. Store included accessories on the Accessory Posts on the pod.
6. Remove Odor Neutralizer Technology Dial from bag. Flip up the dial handle,
align the teal arrows, then insert the dial into the nozzle.
7. To lock and engage the dial, rotate it counterclockwise until it clicks
into the desired odor intensity setting.
- More detailed odor neutralizer technology assembly instructions and visuals on the following two pages.
IMPORTANT: For proper operation, ensure all connections are securely clicked into place.
TECHNOLOGY SETTINGS
SETTINGS
ODOR DIAL
Flip up the dial handle and rotate the odor dial to adjust odor neutralizer technology intensity or to unlock the dial for cartridge access.
Insertion/Removal: Rotate the odor dial to align the teal arrows. Remove
the dial to access the odor cartridge for removal or replacement.
Low: Rotate the dial toward the Low position to decrease the intensity to
the lowest level when the vacuum is in use.
High: Rotate the dial toward the High position for the highest intensity
level when the vacuum is in use. This position is the recommended setting for
optimal performance.
ODOR NEUTRALIZER TECHNOLOGY TIPS
Odor Dial Must be Installed for Vacuum to Function Properly
- Remove odor cartridge from dial if you don’t want the benefits of the odor neutralization
technology.
Maintenance Required
- Clean all filters as recommended under Cleaning Filters.
- Empty the dust cup before storing your vacuum.
- Replace the cartridge as recommended under Odor Cartridge Replacement.
- Visit qr.sharkclean.com/odortech to learn more and purchase replacements.
- If wet pet messes are cleaned up, thoroughly clean the vacuum.
Fragrance Strength Over Time
- The intensity of the odor neutralizer technology’s fragrance may diminish over time. It may
also have no noticeable fragrance at all. This is natural and does not indicate the technology
isn’t working. Follow replacement instructions to ensure continued performance.
NOTES:
- The odor dial needs to be installed for the vacuum to function properly, with or without the odor cartridge.
- Odor Neutralizer technology effectively deodorizes while interacting with odors from inanimate sources.
ODOR NEUTRALIZER TECHNOLOGY
ODOR CARTRIDGE REPLACEMENT
1. REMOVE ODOR DIAL FROM NOZZLE
Flip up the handle and rotate the dial clockwise until the two teal arrows are aligned. Pull the handle to remove the dial from the nozzle.
2. REMOVE OLD ODOR CARTRIDGE
Rotate the cartridge counterclockwise in the dial housing and pull out the cartridge to remove it.
3. REMOVE NEW CARTRIDGE FROM BAG
Remove the new odor cartridge from the sealed packaging. To maintain the life of the cartridge, keep it in the sealed packaging until you are ready to install it.
4. INSTALL NEW CARTRIDGE IN DIAL
Align the yellow arrow on the side of the cartridge with the yellow arrow on the side of the dial cover, then insert the cartridge into the dial. Rotate the cartridge clockwise to lock it in place.
5. INSTALL DIAL IN NOZZLE
Align the teal arrow on the dial cover with the teal arrow on the nozzle, then reinsert the dial into the nozzle. Rotate the dial counterclockwise until it clicks into an intensity setting to engage. Rotate further to change the intensity setting.
6. USED CARTRIDGE DISPOSAL
Dispose of the old cartridge by dropping it into the trash.
NOTE : Odor cartridges should be replaced every 6 months for optimal odor neutralizer technology performance.
WHOLE-HOME CLEANING
SETTINGS
POWER SWITCH:
Press power button to turn on vacuum. Please note the brushrolls will not spin unless the wand is reclined.
NOTE : Try using Hard Floor mode for low pile area rugs.
SURFACE SELECTOR:
Thick Carpet & Area Rug Cleaning
Slide the surface switch to the top position to select Thick Carpet/Area Rug.
Carpet & Low Pile Cleaning
Slide the surface switch to the middle position to select Carpet/Low Pile to
increase the speed of the brushrolls and to help remove stuck-on dust and
debris.
Hard Floor Cleaning
Slide the surface switch to the bottom position to select Hard Floor.
HEADLIGHT INDICATOR LIGHTS
HEADLIGHTS:
The headlights will flash or turn red to indicate issues that need attention.
Solid White Lights: The brushrolls are spinning and the unit is working
as it should.
Solid Red Lights: There is a jam in the brushroll area. Turn off the
vacuum and unplug it, then remove any blockages in the nozzle.
Flashing Red Lights: The motorized floor nozzle is overheating. Turn off
the vacuum, unplug it, and remove any blockages. Let the vacuum cool down for
at least 60 minutes before restarting. See Troubleshooting section for more
information.
Flashing White Lights: The vacuum is operating in an environment that is
either too hot or too cold. This vacuum will only function properly in
temperatures ranging from 32°F (0°C) to 104°F (40°C). Turn the vacuum off and
adjust the room temperature.
NOTE : For deep cleaning per ASTMF608 (embedded dirt in carpets), please set to Carpet/Low Pile mode.
NOTE : For maximum suction for above-floor cleaning per ASTM F558, set to Hard Floor mode.
CLEANING MODES
UPRIGHT:
To engage brushrolls, step on floor nozzle and tilt handle back.
ABOVE-FLOOR—HANDLE:
Press the Handle Release button to detach the handle from the wand.
ABOVE-FLOOR—WAND:
Press the Wand Release button to detach the wand from the pod.
POWERED LIFT-AWAY®:
Press the Lift-Away button to detach the pod from the floor nozzle.
LIFT-AWAY®:
With pod removed, press the Wand Release button to detach the wand from the floor nozzle.
NOTE : All accessories are compatible with both the wand and the handle.
EMPTYING THE DUST CUP
IMPORTANT : Unplug the power cord before performing any maintenance.
To remove Dust Cup, press release button on top of the pod. Tilt dust cup away from wand, then lift to remove.
To empty debris into the trash, push the lever on the back of the dust cup and the lid will drop open. To close the lid, pull the lever back until it clicks into place.
To remove collected debris from Lint Screen, press Handle Releas e button and lift handle to access screen.
To reinstall, place bottom of dust cup into pod and then tilt until it clicks into place.
CLEANING AND REPLACING THE FILTERS
CLEANING FILTERS
Regularly rinse and replace the filters to maintain your vacuum’s suction
power and to maximize the effectiveness of the odor neutralizer technology.
To prevent damage from cleaning chemicals, rinse filters with cold water only.
Allow all filters to air-dry for at least 24 hours before reinstalling them to
prevent liquid from being drawn into electric parts.
IMPORTANT : DO NOT use soap when cleaning the filters.
CLEAN PRE-MOTOR FILTERS EVERY MONTH
Remove Dust Cup, then lift out the Foam and Felt Filters.
CLEAN HEPA FILTER EVERY YEAR
With the dust cup removed, pull the tab on the bottom of the pod to release
the Filter Door.
Lift off the door, then remove the HEPA Filter.
To reinstall, insert HEPA Filter into unit and replace filter door.
NOTES:
- The pre-motor filters should be replaced every 2.5 years. The HEPA filter should be replaced every 3 years.
- Vacuum seal is effective against inanimate allergens such as dust and dirt particles.
MAINTENANCE
NOZZLE MAINTENANCE
SELF-CLEANING BRUSHROLL
If any hair is wrapped around the brushroll, continue vacuuming, using
Carpet/Low Pile mode on a bare floor surface, a low-pile carpet, or a small
area rug. This will allow the self-cleaning brushroll to remove the hair wrap
and send it to the dust cup.
If you run over a hard or sharp object or notice a noise change while
vacuuming, check for blockages or objects caught in the brushroll.
If some fibers remain wrapped around the brushroll after continued use, clear
them from the brushroll.
CLEANING THE SOFT ROLLER
Slide the Soft Roller access button forward to release the Soft Roller.
Hand wash the Soft Roller as needed. Use only water, and allow it to air-dry completely for at least 24 hours. Reinsert the Soft Roller in the front of the nozzle until it clicks into place.
CORD MAINTENANCE
To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. If this occurs, immediately shut off power to the vacuum and remove the cord from the brushroll or nozzle.
1. DO NOT pull or carry vacuum cleaner by the cord or use cord as a handle.
2. D O NOT unplug by pulling on the cord. Grasp the plug, not the cord.
3. D O NOT close the door on the cord.
4. DO NOT pull the cord around sharp corners.
5. D O NOT leave the cord near heated surfaces.
CHECKING FOR BLOCKAGES
HOSE BLOCKAGE
Detach hose from vacuum pod, and check hose and opening on back of pod for blockages.
WAND BLOCKAGE
Detach wand from floor nozzle and handle, and check both ends for blockages.
NOZZLE BLOCKAGE
Detach wand from floor nozzle, tilt nozzle neck back, and check opening for blockages.
HANDLE/HOSE BLOCKAGE
Detach handle from wand and hose from the vacuum pod, and check openings for blockages.
NOZZLE HOSE BLOCKAGE
To access the nozzle hose, pinch the release touchpoints on the bottom of the nozzle, then lift the cover and clear any blockages.
AVAILABLE ACCESSORIES
A. Crevice Tool
This slender tool offers extended reach to access corners, baseboards, tight
spaces, and ceilings.|
---|---
B. Upholstery Tool
Picks up hair, dust, and large debris from mattresses, couches, curtains,
lampshades, and other delicate upholstered fabrics.|
C. Pet Multi-Tool
A single convertible tool for cleaning tough pet messes two ways: use the
stiff bristle brush to clean stuck-on debris, or take off the bristles to
reveal an upholstery tool perfect for removing stubborn pet hair and large
piles of debris.|
D. Duster Crevice Tool
Two cleaning tools in one. The crevice tool gives you extended reach to clean
in tight spaces, while the soft brush is ideal for dusting delicate surfaces.|
E. Pet Power Brush
The turbine brush loosens and removes pet hair and debris from carpets, and
powerfully deep-cleans dander out of upholstery and other surfaces.|
F. Under-Appliance Wand
Clean under and behind hard-to-move appliances and furniture with this
adjustable 36” tool. Flip the extension piece over to clean the underside of
appliances.|
G. Anti-Allergen Dust Brush
This brush features nylon fiber bristles specifically designed for removing
fine dust and allergen particles from the most delicate surfaces.|
H. HairPro Self-Cleaning Pet Power Brush
Tackles pet hair and ground-in dirt from above-floor areas like carpeted
stairs and upholstery, while actively removing hair wrap as it cleans.|
I. Home & Car Detail Kit
Deep-clean your car like a professional detailer, or clean hard-to-reach areas
in your home. Micro-sized tools let you clean around delicate objects and
access the tightest spaces like car vents and computer keyboards|
J. Accessory Bag
This convenient accessory storage bag measures 32 cm x 70 cm and fits the
Under- Appliance Wand. Smaller size available at sharkaccessories.com.|
NOTE : Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap of the box. To order additional accessories, visit sharkaccessories.com.
TROUBLESHOOTING
Power cord caught in brushroll or floor nozzle.
- To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. If this occurs, immediately shut off power to the vacuum and remove the cord from the brushroll or nozzle.
- Inspect power cord and plug for any damage before use. DO NOT use vacuum cleaner with a damaged cord or plug. Turn off all controls before plugging in or unplugging the vacuum cleaner. Store your vacuum cleaner with the power cord secured around the two cord hooks.
Vacuum is not picking up debris. No suction or light suction.
- Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinstalling them.
- Dust cup may be full; empty dust cup.
- Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any blockages found. See Checking for Blockages section for more information.
- If any hair, string, or carpet fibers are wrapped around the brushroll, extend cleaning time to allow the self-cleaning brushroll to remove them. If some hair or fibers remain wrapped around brushroll after continued use, carefully remove them. See Cleaning the Brushroll section for more information.
Vacuum lifts area rugs.
-
Make sure Surface Selector switch is set to the Thick Carpet/Area Rug setting.
-
Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Brushrolls do not spin. -
If the Headlight Indicator Lights turn red, immediately turn off and unplug the vacuum.
Remove pod and wand from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum, and turn on power. -
With the power on, recline the handle, which will automatically turn on the brushrolls.
Vacuum turns off on its own or headlight indicator light flashes red.
If your vacuum overheats, the thermostat will automatically turn off the
motor. Perform the following steps to restart:
1. Turn vacuum off and unplug it.
2. Empty dust cup and clean filters. See Emptying the Dust Cup and Cleaning
and Replacing the Filters sections for more information.
3. Check for blockages in hose, wand, floor nozzle, accessories, and inlet
openings.
4. Allow unit to cool for a minimum of 60 minutes.
5. Plug in vacuum and turn it on.
Vacuum is emitting air that smells bad.
- Dust cup may be full; empty dust cup. Empty dust cup after each use for optimal odor neutralizer technology performance.
- Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinstalling them.
- Check to make sure odor cartridge is installed in the dial and the dial is installed in the nozzle.
- Check the odor neutralizer technology dial on the nozzle to see what setting is enabled.
- If odor neutralizer technology dial is at any setting from Low to High and the cartridge has been installed for 6 months or longer, consider replacing it.
- If the odor cartridge is still emitting a scent but you dislike it, consider turning the intensity down, or reinstall the dial in the nozzle without the cartridge.
- If the odor neutralizer technology cartridge is not emitting a scent, consider replacing it.
For all other issues, please go to support.sharkclean.com/ or call Customer Service 1-800-798-7398.
SHARK | NINJA
FIVE (5) YEAR LIMITED WARRANTY
The Five (5) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja Operating LLC. Warranty coverage applies to the
original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of five (5) years from the date of purchase when it
is used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in
SharkNinja’s sole discretion, will be repaired or replaced up to five (5)
years from the original purchase date.
2. I n the event a replacement unit is issued, the warranty coverage ends six
(6) months following the receipt date of the replacement unit or the remainder
of the existing warranty, whichever is later. SharkNinja reserves the right to
replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as foam filters, HEPA
filters, pads, etc.), which require regular maintenance and/or replacement to
ensure the proper functioning of your unit, are not covered by this warranty.
Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids),
abuse, negligent handling, failure to perform required maintenance (e.g., not
cleaning the filters, not removing debris from the brushroll), or damage due
to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These
defects include damages caused in the process of shipping, altering, or
repairing the SharkNinja product (or any of its parts) when the repair is
performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty period, visit sharkclean.com/support
for product care and maintenance self-help. Our Customer Service Specialists
are also available at 1-800-798-7398 to
assist with product support and warranty service options, including the
possibility of upgrading to our VIP warranty service options for select
product categories. So we may better assist you, please register your product
online at registeryourshark.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for
repair or replacement. A fee of $25.95 (subject to change) will be charged
when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to
initiate a warranty claim. You will need the receipt as proof of purchase. We
also ask that you register your product online at registeryourshark.com and
have the product on hand when you call, so we may better assist you. A
Customer Service Specialist will provide you with return and packing
instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you.
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using mobile device
Scan here or visit
qr.sharkclean.com/odortech for more
information
Benefits of registering your product and creating an account:
- Get easier, faster product support and access to warranty information
- Access troubleshooting and product care instructions
- Be among the first to know about exclusive product promotions
TIP : You can find the model and serial numbers on the QR code label on the bottom of the back of the vacuum pod.
RECORD THIS INFORMATION
Model Number: _
Serial Number: __
Date of Purchase: _
(Keep receipt)
Store of Purchase: ___
TECHNICAL SPECIFICATIONS
Voltage: 120V~, 60Hz
Watts: 1416W
ODOR NEUTRALIZER TECHNOLOGY SPECIFICATIONS
1. Product Name: Odor Neutralizer Technology Cartridge
2. Manufacturer: Shark Ninja 89 A Street Needham, MA 02494
3. Weight: 17.6g / 0.62oz
4. Ingredients: Solid SM composite polymer C17 + fragrance SE 272235
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of
your new Shark® STRATOS™ DuoClean® PowerFins™ HairPro™ Powered Lift-Away® with
Self-Cleaning Brushroll and Odor Neutralizer Technology Upright Vacuum.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
Illustrations may differ from actual product. We are constantly striving to
improve our products; therefore the specifications contained herein are
subject to change without notice.
This product may be covered by one or more U.S. patents. See
sharkninja.com/patents for more information.
© 2022 SharkNinja Operating LLC. DUOCLEAN, LIFT-AWAY, POWERED LIFT-AWAY, and SHARK are registered trademarks of SharkNinja Operating LLC. POWERFINS, HAIRPRO, and STRATOS are trademarks of SharkNinja Operating LLC.
AZ3000_Series_IB_E_MP_Mv6