Craftmade TOP52FB5 Remote Control DC Motor Ceiling Fan Instruction Manual

Craftmade TOP52FB5 Remote Control DC Motor Ceiling Fan

120X155mm
INSTRUCTION FOR DC MOTOR CEILING FAN REMOTE CONTROL

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement.

WIRING SCHEMATIC DIAGRAM FOR RECEIVER

POWER PARAMETER LIST

Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth. (Emitter and receiver must be sent back to factory for maintenance if damaged.)
Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction With the memory function, the controller can save the status( light and direction) while the supply power OFF and resume to the original after reload the power supply.

FUNCTION INSTRUCTION OF EMITTER

1. CD indicator light

2. Power ON/0FF

3. Fan0N/0FF

4. Speed of the fan(llowspeed~6highspeed)

5. Natural wind

6. Direction of the fan (Reverse switch)

7. CD Fan timing

8. nightlight

9. Dim + or-

10.  High-low off

11. CCT + or –

12. Learning Key

13. Indicator light

14. Power ON/OFF

15. Fan ON/OFF

16. Speed of the fan(1Low speed~ 6 high speed)

17. Direction of the fan Reverse switch)

18. CD Fan timing

19. nightlight

20. Dim + or –

21. Light on/off

22. CCT + or –

23. RGB Change

24. RGB Model

25. Learning Key

KINDLY REMINDERS :

1.  Learning code matching mode is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “ ” button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learning successfully and it can works normally. (PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds)
2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
3. When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
4. Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will be dimmed when the battery get low voltage), must replace if the battery is getting low voltage.
5. Please take out the battery from the emitter when leaving unused for long time.
6. The maximum load of lighting see the above “POWER PARAMETER LIST” PS: please connect the ground wire correctly, otherwise it may cause the light micro-light or flash
7. When installing the fan the fan ceiling cover don’t press the antennal or other wire) it is easy to breakdown the wire and short-circuited.

120X155mm
INSTRUCTION FOR DC MOTOR CEILING FAN REMOTE CONTROL

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement.

WIRING SCHEMATIC DIAGRAM FOR RECEIVER

POWER PARAMETER LIST

Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth. (Emitter and receiver must be sent back to factory for maintenance if damaged.)
Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction With the memory function, the controller can save the status( light and direction) while the supply power OFF and resume to the original after reload the power supply.

FUNCTION INSTRUCTION OF EMITTER

1. CD indicator light

2. Power ON/0FF

3. Fan0N/0FF

4. Speed of the fan(llowspeed~6highspeed)

5. Natural wind

6. Direction of the fan (Reverse switch)

7. CD Fan timing

8. nightlight

9. Dim + or-

10.  High-low off

11. CCT + or –

12. Learning Key

13. Indicator light

14. Power ON/OFF

15. Fan ON/OFF

16. Speed of the fan(1Low speed~ 6 high speed)

17. Direction of the fan Reverse switch)

18. CD Fan timing

19. night light

20. Dim + or –

21. Light on/off

22. CCT + or –

23. RGB Change

24. RGB Model

25. Learning Key

KINDLY REMINDERS :

1.  Learning code matching mode is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “ ” button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learning successfully and it can works normally. (PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds)
2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
3. When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
4. Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will be dimmed when the battery get low voltage), must replace if the battery is getting low voltage.
5. Please take out the battery from the emitter when leaving unused for long time.
6. The maximum load of lighting see the above “POWER PARAMETER LIST” PS: please connect the ground wire correctly, otherwise it may cause the light micro-light or flash
7. When installing the fan the fan ceiling cover don’t press the antennal or other wire) it is easy to breakdown the wire and short-circuited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>