SAMS POL Series Polaris Sportsman Reverse Light Kit Installation Guide
- August 26, 2024
- SAMS
Table of Contents
- SAMS POL Series Polaris Sportsman Reverse Light Kit
- FAQs
- Installation Manual
- Included
- Required Tools
- Remove Seats & Shifter
- Remove Center Console
- Secure & Plug-in Controller
- Mounting the Light
- Route Power to Light
- Reinstall Plastics
- CONTACT INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SAMS POL Series Polaris Sportsman Reverse Light Kit
FAQs
Q: Is this kit compatible with all Polaris RZR models?
A: The Polaris 2024+ RZR Single Light Reverse Light Kit is designed specifically for certain Polaris RZR models. Please check compatibility before purchasing.
Q: What should I do if I encounter issues during installation?
A: If you encounter any difficulties during installation, please contact our customer support at support@samsbackuplights.com for assistance.
Installation Manual
Included
Description | Quantity |
---|---|
Wiring Harness | 1 |
Relay | 1 |
Light | 1 |
Zip Ties (Medium) | 4 |
Zip Ties (Large) | 4 |
Required Tools
Torx T-30
5/16” Allen Wrench
Philips Screwdriver
Utility Knife
3/8” Socket
Read the entire manual before beginning the installation process. Disclaimer: Sam’s Backup Lights is not responsible for any damage due to improper installation.
Remove Seats & Shifter
- Remove seats by pulling up on the red release at the rear of the seat.
- Remove the shifter top by removing the T-25 screw and removing the cover.
- Remove the T-25 screw uncovered by the cover. Pull up to remove the shifter.
Remove Center Console
- Remove the front center console by removing 7 T-40 screws and the three push rivets. Remove the center console.
- To remove the rear cup holders, unscrew the 4 T-40 screws and remove the three push rivets. (Watch out for the wires for the 12V Plug). Note: this is only for a 4-seater
- Remove the rear cover by turning the four push locks and pulling on the cover.
Secure & Plug-in Controller
- Remove the diagnostic connector cover and plug in the connector included with the reverse light wiring harness.
- Secure controller, relay, and fuse using zip ties.
- Remove the cover for the bus bar and plug in the power and ground.
- Plug in the control box.
Mounting the Light
- Remove rear plastics if needed; drill a hole in the center of a mounting spot as shown in the figure below.
- Mount light to provided bracket. (Be sure to slide the bolt through the bracket before attaching a light to it).
- Secure light with provided hardware.
Route Power to Light
-
Route the reverse light harness down from the control box position into the cab, and, following the OEM harness, run straight through the cab.
-
Route wiring harness behind the cab, along the OEM harness to the rear of the vehicle.
-
Plug the wiring harness connector into the light connector.
-
Zip tie as needed.
Note: If installing the kit on a 2-seater, coil excess wire either by- control box or directly behind the seat.
Reinstall Plastics
Operation of Reverse Lights
Our controllers have been programmed with a manual override feature. Back-up lights may be turned on without the vehicle in reverse.
Fully Automatic when shifted to Reverse Gear
- No programming required
Manual Override Function
- Shift the vehicle into Neutral
- Press and hold the brake pedal for up to 2 seconds. The reverse light will automatically turn on and stay on.
-
- To turn the light off repeat this procedure.
-
- Note: If the ignition is turned off while the vehicle is in reverse, or the manual override function is enabled the lights will remain ON until the ECU enters sleep mode (approximately 30 secs to 2 minutes depending on vehicle and ECU type).
CONTACT INFORMATION
- Sam’s Backup Lights
- www.samsbackuplights.com
- 2024+ Polaris RZR Reverse Light
- support@samsbackuplights.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>