ATTOWAVE AMWUA2404 Wi-Fi and Bluetooth Module User Manual

: August 27, 2024
: AttoWave

Table of Contents

ATTOWAVE AMWUA2404 Wi-Fi and Bluetooth Module
Introduction
Features
Specifications Table
Pin Definition
Electrical Characteristics
Federal Communications Commission Interference Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ATTOWAVE AMWUA2404 Wi-Fi and Bluetooth Module

Specifications

Product Description: Wi-Fi&Bluetooth LE V5.0 Module
Major Chipset: ESP32-C3
Host Interface: UART
Dimension: 25 x 15 x 1 mm (L x W x H)
Antenna: Inverted-F Antenna (Built-in)

Product Overview
The AMWUA2404 is a Wi-Fi&Bluetooth Module by Attowave co., Ltd. designed to add Wi-Fi&Bluetooth capabilities to Radar detectors. It utilizes Wi- Fi&Bluetooth Low Energy technology to establish communication between the Radar detector and a smartphone equipped with Wi-Fi&Bluetooth LE.

Features

Wi-Fi &Bluetooth: Enables Wi-Fi&Bluetooth connectivity

Specifications Table
General

Wi-Fi Feature:
- Frequency Range: 2412 ~ 2462 MHz
- Modulation: OFDM for Wi-Fi 802.11b/g/n
- Channel Number: 20MHz: 11, 40MHz: 7
Bluetooth Feature:
- Bluetooth Version: BLE 5.0
- Frequency Range: 2402 ~ 2480 MHz
- Modulation: GFSK for Bluetooth
- Channel Number: 40
- Bit Rate of Transmitter: 1Mbps
Operating Conditions Feature:
- Voltage: 3.3V
- Operating Temperature: -20 ~ 80°C
- Operating Humidity: TBD
- Storage Temperature: -40 ~ 85°C
- Storage Humidity: TBD
- ESD Protection: Human Body Model Changed Device Model

Pin Definition
Electrical Characteristics
Federal Communications Commission Interference Statement

FAQ
Frequently Asked Questions:

Q: What is the purpose of the AMWUA2404 module?
A: The AMWUA2404 module is designed to add Wi-Fi&Bluetooth functionality to Radar detectors for communication with compatible smartphones.

Introduction

Product Overview
The AMWUA2404 was an Attowave co., Ltd. Wi-Fi&Bluetooth Module. The AMWUA2404 is used to add Wi-Fi&Bluetooth to Radar detectors. It uses Wi-Fi&Bluetooth Low Energy to communicate between the Radar detector and a Wi-Fi&Bluetooth LE equipped smartphone.

Features

Wi-Fi &Bluetooth

ESP32-C3
Processor
32-bit RISC-V single-core processor, up to 160MHz
AES-128bit encryption Processor
Memory
384 KB ROM
400 KB Retention SRAM
External Flash
16M-Byte SPI Flash
Operating Clock
40MHz
Antenna
Inverted-F Antenna
IO Interfaces
UART
SWD
GPIO
Power Input
Single 3.3V Power Input
Package
Module – 25 x 15 x 1 mm (L x W x H)

Specifications Table

General

Feature	Description
Product Description	Wi-Fi&Bluetooth LE V5.0 Module
Major Chipset	ESP32-C3
Host Interface	UART
Dimension	25 x 15 x 1 mm (L x W x H)
Antenna	Inverted-F Antenna (Built-in)

Wi-Fi

Feature	Description
Wi-Fi	IEEE 802.11 b/g/n-compliant
Frequency Range	2412 ~ 2462 MHz
Modulation	OFDM for Wi-Fi
Channel Number	802.11b/g/n 20MHz : 11

802.11n 40MHz : 7

Bluetooth

Feature	Description
Bluetooth version	BLE 5.0
Frequency Range	2402 ~ 2480 MHz
Modulation	GFSK for Bluetooth
Channel Number	40
Bit Rate of Transmitter	1Mbps

Operating Conditions

Feature	Description

Operating Conditions
Voltage| 3.3V
Operating Temperature| -20 ~ 80℃
Operating Humidity| TBD
Storage Temperature| -40 ~ 85℃
Storage Humidity| TBD
ESD Protection
Human Body Model| TBD
---|---
Changed Device Model| TBD

Pin Definition

Pin name	Basic Description	Type	Level

Electrical Characteristics

Absolute Maximum Ratings

Symbol	Parameter	Min	Typ	Max	Unit
VDD3P3	3.3V power supply		3.3	3.6	V

Recommended Operating Conditions

Symbol	Parameter	Min	Typ	Max	Unit
VDD3P3	3.3V power supply	3.0	3.3	3.6	V

Digital IO Pin DC Characteristics

Symbol	Parameter	Min	Typ	Max	Unit
VIH	Input High Voltage	0.84			V
VIL	Input Low Voltage			0.36	V

Federal Communications Commission Interference Statement

Liability for illegal acts
Anyone who uses this product for illegal purposes shall be liable and he or she shall be held responsible for all and any consequences.

FCC licensing information
λ Federal Communications Commission Interference statement
NOTE: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio, TV technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two Conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

NOTE: To comply with FCC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.

RF exposure statements
NOTE: The modular transmitter NO its own RF shielding, and tested inside of a host device.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.
We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer. If any hardware modify or RF control software modify will be made by host manufacturer, C2PC or new certificate should be apply to get approval, if those change and modification made by host manufacturer not expressly approved by the party responsible for compliance ,then it is illegal.
If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “CONTAINS FCC ID: AMWUA2404”