INFINITY IT-8500 X3 3D 4D Massage Chair User Guide

: August 26, 2024
: Infinity

Table of Contents

INFINITY IT-8500 X3 3D 4D Massage Chair
Specifications
FAQs
INSTALLATION STEPS
Final Check
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INFINITY IT-8500 X3 3D 4D Massage Chair

Specifications

Model: IT-8500TM X3
Type: 3D/4D Massage Chair
Power: 110V
Manufacturer: INFINITY

FAQs

Q: How do I control the chair using an app?
- A: Download the app from Apple or Google app store and follow pairing instructions within the app.
Q: What should I do if the chair is not operating correctly?
- A: Review all assembly steps. Contact Infinity support at 1-603-910-5000 for US-based support.

INSTALLATION STEPS

Step 1:
- Before assembly, carefully unpack all box contents. Check the box contents in the detail below. Make sure all contents are accounted for.
- If anything is missing, please contact INFINITY at 603-910-5000. Do not return to the place of purchase.
Step 2:
- Connect the chair power cord to a grounded 110V electrical outlet and plug it into the respective port on the back side of the base of the chair. Flip the main power switch to on.
Step 3:
- Plug the remote control cord into the remote control port also located on the backside of the base of the chair. Ensure the arrow on the top of the remote control cord is facing up. Screw on to fasten. Do not force.
Step 4:
- Press the power button on the remote control once to turn it on, then once more to bring the chair into the upright position. To protect you and the remote control during assembly, unplug it from the chair and switch the main power off.
Step 5:
- Attach the back cushion by draping it over the top of the chair body and zippering it to the zipper located on the top of the back of the chair body.
Step 6:
- On the left hip side, locate and connect the air hose to the air nozzle on the body of the chair; also connect the power input to the chair body power cord and fasten it.
- On the right-hand side, locate and connect the three air hoses from the back cushion to their corresponding air nozzles based on the numbers labeled on each.
- Zipper the closure between the Seat Cushion and Back Cushion.
Step 7:
- If attached, remove the plastic shelving of the arm panel from the arm panel lock. The arm panel lock can be accessed from the back side of the shelving. To release the arm panel lock push down on the release lever.
Step 8:
- Take 3 locking nuts from the bag of parts and place them into the 3 holes along the inside of the plastic shelving. Make sure the + is facing out on the locking nuts.
Step 9:
- Using the screwdriver provided, rotate each locking nut to bring the open side facing up. You can ensure the open side is facing up by looking at the hole on the top of the shelving. To access the middle nut, pull up on the lever on the base of the backrest and push the backrest forward. After fastening, make sure the backrest locks back into place.
Step 10:
- Place the arm panel onto the plastic shelving, lining up the two air hoses on the body of the chair with the rubber grommet on the underside of the arm panel, as well as the three arm panel pins into the holes in the plastic shelving.
- Tighten the 3 locking nuts to secure the arm in place, again temporarily releasing the lever to push the backrest forward and access the middle nut.
Step 13:
- Shimmy the arm panel upward and towards the front of the chair until the pin on the side of the chair body secures into the arm panel lock.
Step 12:
- Before attaching the shoulder panels, ensure the airbag is toward the front of the chair. Connect the white plug until it clips.
Step 13:
- Slide the metal joint pins into the opening on the chair body until the Shoulder Panel secures into place.
Step 14:
- On the inside of the shoulder panel, locate and open the small sliding door where you will see a screw. Screw in clockwise tightly and then close the sliding door when the shoulder panel is fully secured.
Step 15:
- Remove the footrest from its packaging and position it in front of the main chair body. Connect the footrest by attaching the electrical plug from the footrest to the port on the body of the chair. Ensure the thumb release is facing up and push in until it snaps. Slide the air hose onto the white air nozzle.
Step 16:
- Lift and pull the back flap on the footrest. Slide the footrest in and shift it until the mounting bracket is properly aligned with the screw holes located on the body of the chair. Insert the hex screws through the screw holes to fasten the footrest to the body of the chair. Repeat on the other side. Tighten with Hex Key.

Final Check

Plug the remote cord back into the input port located on the back of the base of the chair. Ensure the arrow on the top of the input jack is facing up.

Remote Pouch

Attach the remote pouch using velcro found underneath the right armrest

Review the chair for smooth operation. If things are not operating correctly, review all assembly steps. Call Infinity support at 1-603-910-5000 if you need live US-based support.
If you wish to use an APP to control the chair, download it from the Apple or Google app store and follow the pairing instructions found within the APP.
You are done; time for a Massage!
SCAN CODE
Register your product at www.infinitymassagechairs.com/ warranty to ensure it is in our system. This will simplify the warranty process should you ever need it.
Alternatively, scan the QR code to go directly to the URL above.

CONTACT INFORMATION

72 Stard Road, Seabrook,
NH 03874
603-910-5000
www.infinitymassagechairs.com.
Version 1.2
SCAN CODE
Before assembling your chair, watch an assembly video at: www.infinitymassagechairs.com/assembly-tutorials Alternatively, scan the QR code to go directly to the URL above.