genexis P3420 FiberTwist-Series Installation Guide
- June 5, 2024
- genexis
Table of Contents
P3420
FiberTwistSeries
Installation Guide
Button overview
Port overview
LED overview
Installation guide
Different language versions of this document and additional product information are available on https://genexis.eu/product/fibertwist/downloads
Box contents
- Genexis FiberTwist (active device)
- Power adapter
- Label (self-adhesive)
- Installation Guide (this document)
Label position
The product label is positioned on the back of the active device.
Preparation
Ensure there is a power socket within reach of where the device is being
installed.
Important: Instructions need to be followed precisely and uninterrupted. This minimizes the risk of damage to the fiber optic connectors, causing severe degradation of signal quality.
Remove Blind Cover (if present)
- Press and hold the unlock button (see button overview).
- Rotate the Blind Cover counterclockwise till it blocks.
- emove the Blind Cover from the baseplate (FTU) by pulling it towards yourself.
- Store the Blind Cover in a safe place.
Remove dust cap
- Take the FiberTwist out of the box.
- The dust cap is connected to the red string located on the rear of the FiberTwist.
- Remove the dust cap by pulling the red string.
- Store the dust cap in a safe place.
Twist!
- Place the FiberTwist on the FTU as shown in the picture below, in a 30–degree angle.
- Rotate clockwise until it clicks into place.
- Make sure the FiberTwist is aligned squarely on the FTU, each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Connecting the FiberTwist
- If required, connect your television / set-top box to the TV port with a coax cable.
- If required, connect your personal devices to the LAN ports via an RJ45 network cable.
- Connect the supplied power adapter to the FiberTwist and plug the adapter into a power socket.
Changing your router settings
Depending on the network configuration of your operator, the FiberTwist-P3420
can also provide support for routing functionalities. If this is the case, the
router settings can be changed by logging in to the web GUI using the below
instructions. If routing functionality is not supported by your Service
Provider, the web GUI will not be reachable.
- Connect a computer to one of the LAN ports.
- Log in to the web GUI by browsing http://router/
Your username and password can be found on the label inside the product box.
If at some point in the future it becomes necessary to uninstall the
FiberTwist, please place the Blind Cover back on the FTU immediately and put
the dust cap back on the FiberTwist.
Warning: The FiberTwist is a Class 1 laser product.
EU Declaration of Conformity
Hereby, Genexis B.V. declares that the product FiberTwist-P3420 is in
compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated
Directive 2015/863 and Ecodesign Directive 2009/125/EC.
The full texts of the EU declaration of conformity are available at the
following internet address: https://genexis.eu/red/ft-P3420
Company Name
Genexis B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of the authorized person
Maarten Egmond, CTO
Signature of the authorized person
Place of issue
Eindhoven
The Netherlands
Date of issue
2020-07-03
Revision 1.3 – June 2021 – Copyright © 2021 Genexis Netherlands B.V. All
rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document.
Genesis reserves the right to change, modify, transfer, or otherwise revise
this publication without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>