genexis Pulse EX600 Mobile Devices Installation Guide
- June 3, 2024
- genexis
Table of Contents
genexis Pulse EX600 Mobile Devices
Installation with use of app
You’re just a few steps away to install your device via the Genexis EasyWiFi
app
Installation guide
Pulse EX600 can be setup as a router or wireless/wired extender.
Various translations of this document (if available) and additional product
information can be found on https://genexis.eu/product/pulse/downloads
Box contents
- Genexis Pulse EX600
- Power adapter
- Network cable
- Labels (self-adhesive)
- Plugs & screws
Placement
Pulse EX600 supports two placement options; desktop and mounted to a wall. It
is recommended to place the device ‘away’ from objects.
Desktop
Place the device horizontally on a flat surface.
Wall mount
- Download and print the drilling guide from https://genexis.eu/product/pulse/downloads
- Use the drilling guide to drill the holes, insert plugs and put screws into place.
Use the wall mount points on the back of the Pulse EX600 to mount the device to the screws.
Installation of your Pulse device(s)
This installation guide is for installing the Pulse EX600 as a router, as
explained on the right. In addition, an extra Pulse EX600 can be installed as
a wireless or wired extender behind the Pulse EX600 router.
If you already have a different router (not a Pulse EX600) and want to install
it as an extender, then look for installation options: https://genexis.eu
/pulse-installation-guide
Router
If you do not have a router installed, start installing your Pulse EX600 here:
- Place your Pulse EX600 near your broadband outlet.
- Connect a network cable between your broadband outlet and the Pulse EX600 WAN port (red port).
- Plug the power adapter into an electrical socket and connect it to the power port at the back of the Pulse EX600.
- Flip the ON/OFF switch at the back of the device to turn it on.
- Wait until the Status LED stops blinking and turns solid green.
Your Pulse EX600 is now setup as a router. Your network is now ready to be extended with a wireless or wired extender, as explained on the next pages.
Extender placement
For optimal performance of the Pulse EX600 as extender; place the Pulse EX600
halfway in between your router and the problem area (as shown below). Make
sure placement is within WiFi range of your router. If the extender is placed
too far away, it cannot connect to the router.
- Problem area, improved by Pulse EX600
- Area that is good for placing Pulse EX600
- Area covered by your router
Wireless extender
- Place the additional Pulse EX600 as described on the left.
- Plug the power adapter into an electrical socket and connect it to the power port at the back of the Pulse EX600.
- Flip the ON/OFF switch at the back of the device to turn it on.
- Wait until the Status LED surrounding the Mode button starts blinking green.
- On the Pulse EX600, press and release the Mode button once. The status LED will start blinking blue.
- Press the same Mode button on the Pulse EX600 router within two minutes.
- Automated pairing is now started.
- The Status LED turns solid blue indicating that pairing of the Pulse EX600 extender with the router is successful (the Pulse EX600 will automatically reboot after the automated pairing; this may take up to several minutes).
- Wait until the Status LED stops blinking and turns solid green.
Your Pulse EX600 is now setup as a wireless extender.
Wired extender
- Connect a network cable between the LAN port (yellow connector) of the Pulse EX600 router and the WAN port (red connector) of the Pulse EX600 extender.
- Plug the power adapter into an electrical socket and connect it to the power port at the back of the Pulse EX600 extender.
- Flip the ON/OFF switch at the back of the device to turn it on.
- Wait until the Status LED stops blinking and turns solid green (the Pulse EX600 extender will automatically reboot during the setup; this may take up to several minutes).
Your Pulse EX600 is now setup as a wired extender.
Switching the WiFi ON/OFF
The WiFi function of the Pulse EX600 can be switched ON or OFF by means of the
Mode button.
- Switch OFF: On the Pulse EX600, press and hold the Mode button until the Status LED turns solid yellow.
- Switch ON: On the Pulse EX600, press and hold the Mode button until the Status LED starts blinking green or turns solid green.
Connecting to the wireless network
You can connect your personal device (e.g., mobile phone) to the Pulse EX600
via manual pairing. If automated pairing is prefered, please check for your
specific device how this can be initiated. Before pairing, make sure the
Status LED is solid green. If not, switch the WiFi ON as described in this
installation guide.
Manual pairing
The WiFi network name and WiFi key are printed on the labels of the Pulse
EX600 router.
- Perform a search of available wireless networks on your personal device or scan the QR-code on the label on the bottom of the Pulse EX600.
- Select the WiFi network name printed on the label on the bottom of the Pulse EX600.
- Enter the WiFi key printed on the label of the Pulse EX600.
Follow the instructions of the router in case the Pulse EX600 is in extender mode.
Changing your network settings
You can access the Pulse EX600 web interface (GUI) to change your network
settings. The Pulse EX600 must be in router mode to access the GUI.
- Use a web browser on your personal device and navigate to the GUI URL as printed on the label on the bottom of the Pulse EX600
- Login using the credentials as printed on the labels on the bottom of the Pulse EX600.
Power saving options
Power saving options are available via the web interface.
LED & button overview
Port overview
Reset button (recessed)
Reboot – press and release once Factory reset – press and hold until the
Status LED starts fast blinking green
ON/OFF switch
Switch ON – flip the switch to ON Switch OFF – flip the switch to OFF
Troubleshooting
Is the Status LED solid red?
Contact your service provider.
Is the Status LED solid yellow?
The WiFi of the Pulse EX600 is turned OFF. Please turn the WiFi ON as
described in this installation guide.
Is the Status LED not solid blue after automated pairing (WPS)?
Automated pairing (WPS) between the Pulse EX600 and Genexis router or personal
device failed. Please follow the instructions again to setup the Pulse EX600
as a wireless extender or connecting your personal device to the wireless
network. It might be helpful to move the Pulse EX600 closer to your Genexis
router.
Is the Status LED blinking green for 5 minutes?
- Router: Pulse EX600 does not have a connection with the broadband network. Please verify your wired connection with the broadband outlet or contact your service provider.
- Wireless/wired extender: Connection between the Genexis router and the Pulse EX600 is not stable. Please check the cable connection with the Genexis router or move the Pulse EX600 closer to the Genexis router.
Is the Status LED blinking yellow?
The Pulse EX600 is being upgraded with new software. Please wait until the
Status LED turns solid green again.
Return the Pulse EX600 to factory default settings
With the reset button you can reset the Pulse EX600 to its factory default
settings. You can press this button with a small pin or paperclip.
- Press and hold the reset button until the Status LED starts fast blinking green.
- Wait until the Status LED turns solid green again.
Your Pulse EX600 is now setup as a router again with the settings as printed on the label of the Pulse EX600.
EU Declaration of Conformity
Hereby, Genexis Netherlands B.V. declares that the product Pulse EX600 is in
compliance with Directives 2014/53/EU, 2009/125/EC, 2011/65/EU and Delegated
directive 2015/863.
The full text of the EU declaration of conformity is available at the
following internet address: https://genexis.eu/product/pulse/red/pulse-ex600
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue
Eindhoven
The Netherlands
Date of issue
2021-10-06
Frequency bands and maximum radio frequency power transmitted
The Pulse EX600 operates in the frequency bands of 2,4 Ghz and 5Ghz. The
maximum radio frequency power transmitted in these bands is:
- 20 dBm (100 mW) (EIRP) for the 2400 MHz – 2483.5 MHz band
- 23 dBm (200 mW) (EIRP) for the 5150 MHz – 5350 MHz band *
- 30 dBm (1000 mW) (EIRP) for the 5470 MHz – 5725 MHz band
- In EU, 5150 – 5350 MHz is restricted to indoor.
Revision 1.7 September 2022, Copyright © 2022 Genexis Netherlands B.V. All
rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document.
Genexis reserves the right to change, modify, transfer, or otherwise revise
this publication without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>