sygonix 2446222 WiFi Ball Valve Drive Instruction Manual

Operating Instructions
Wi-Fi ball valve drive
Item no: 2446222

Intended use

The product is an electric valve drive. Install the product on or next to a lever valve and control the valve via the On/Off button or Wi-Fi and mobile app.
The release mechanism allows you to control the valve manually in case of a power failure.
Installation and operation are restricted by the following:

• Outer valve or pipe diameter: min. 12.7 mm (½”), max. 31.75 mm (1¼”)
• Force required to open the valve (Break-To-Open torque): max. 5.88 Nm
• Force required to close the valve (End-To-Close torque): max. 5.88 Nm

The product is designed for private and commercial use.
In commercial institutions, the accident prevention regulations of the Employer’s Liability Insurance Association for Electrical Systems and Operating Materials are to be observed.
The product can be used in schools and training centres. The use must be supervised by trained personnel.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

• Product
• Pipe clamp
• Power adaptor
• Operating instructions

Latest product information

Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Description of symbols

The symbol with the exclamation mark in the triangle is used to indicate important information in this document. Always read this information carefully.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

5.1 General

• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

5.2 Handling

• Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

5.3 Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.
• Never operate the product in direct proximity of strong magnetic or electromagnetic fields or transmitter aerials or HF generators. Doing so can prevent the product from functioning properly.

5.4 Operation

• Moving parts can trap and squeeze body parts. Secure the area around moving parts mechanically to prevent access.
• Consult an expert when in doubt about the operation, safety or connection of the appliance.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  – is visibly damaged,
  – is no longer working properly,
  – has been stored for extended periods in poor ambient conditions or
  – has been subjected to any serious transport-related stresses.

5.5 Power adapter
Do not tamper with power supply components. Risk of death by electric shock!

• Always ensure proper connection.

• Never use damaged power supply components.

• Do not modify power supply components.

• Connect the appliance to a wall socket that can be accessed easily.

• As power supply, only use the supplied mains adaptor.

• Only connect the power adaptor to a normal mains socket connected to the public supply. Before plugging in the power adaptor, check whether the voltage stated on the power adaptor complies with the voltage of your electricity supplier.

• Never connect or disconnect power adaptors if your hands are wet.

• Never unplug the power adaptor from the mains socket by pulling on the cable; always use the grips on the plug.

• For safety reasons, disconnect the power adaptor from the mains socket during storms.

• Do not touch the power adapter if there are any signs of damage, as this may cause a fatal electric shock! Take the following steps:
  – Switch off the mains voltage to the socket containing the power adapter (switch off the corresponding circuit breaker or remove the safety fuse, and then switch off the corresponding RCD protective switch).
  – Unplug the power adapter from the mains socket.
  – Use a new power adapter of the same design. Do not use the damaged adapter again.

• Ensure that cables are not pinched, kinked or damaged by sharp edges.

• Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

Product overview

1 Lever
3 Indicator light
5 Pipe clamp| 2 On/Off button
4 Gear release mechanism
---|---

How it works

To operate the product, you make use of the following components and features:

• On/Off button
  With the on/off button on the product you can open and close the valve.

• Mobile app
  With the mobile app, you remotely close and open the valve. The product must be connected to a Wi-Fi network to receive remote instructions.

• Gear release mechanism for emergency use
  In case of a power failure, you can use the gear release mechanism to open and close the valve manually.

• Default restart status
  The default restart status defines if the valve opens or closes when power is re-established after a power failure. You set the default restart status in the mobile app.

Installation

8.1 Installing
To install the product, clamp it onto the valve or the pipe that is connected to the valve.

A Lever
C Stopper
E Pipe clamp| B Valve lever
D Valve
---|---

PRECONDITIONS:

√ Outer diameter of the lever valve or pipe: min. 12.7 mm (½”), max. 31.75 mm (1¼”)
√ Force required to open the valve (Break-To-Open torque): max. 5.88 Nm
√ Force required to close the valve (End-To-Close torque): max. 5.88 Nm

1. Align the lever (A) with the valve lever (B). Pull the ring of the gear release mechanism and move the lever into the open or closed position (see installation image).
2. Use the pipe clamp (E) and install the product on the valve (D) or pipe. Because the pipe clamp absorbs most of the force, make sure to firmly secure it.
3. Adjust the stoppers (C) to fine adjust the opening and closing points of the valve.

8.2 Connecting to power
To operate the product, connect it to the mains supply via the power adaptor.

WARNING
Motor runs when connecting to power.
Moving parts can trap and squeeze body parts.

• Keep body parts away when connecting power.

1. Connect the power adapter cable to the power supply cable of the product.
2. Connect the power adapter to suitable mains socket.
   → The motor will start and the valve will open or close depending on the factory settings.
   → The product is ready for operation.

Manual operation

Use the On/Off button on the product to operate the product manually.

1. Push the On/Off button to open or close the valve.
   → (If the valve is open) the indicator light on the product is on.

Note:
In normal operation, the valve is always in one of two states: fully closed or fully open.

App operation

After adding the product to the mobile app and connecting it to the Wi-Fi network, you can use the app to remotely control the product.

10.1 Installing the mobile app
Install the TUYA mobile app on your mobile device to operate and control the product.

1. Download the mobile app “Smart Life – Smart Living” from the Google App Store or the Apple App Store.
2. Set up a TUYA account.

10.2 Adding product to mobile app
For mobile app control, you must add the product to the app and connect it to a suitable Wi-Fi network.
Important:
The product can only be connected to 2.4 GHz Wi-Fi networks.

PRECONDITIONS:
√ The TUYA mobile app “Smart Life – Smart Living” is installed on your mobile device.
√ The product is within the range of the Wi-Fi network.

1. On your mobile device, activate Wi-Fi.
2. Connect your mobile device to the Wi-Fi network to which you intend to connect the product.
3. On the product, hold down the On/Off button until the motor starts to move.
   WARNING! Keep body parts away from moving parts.
   → The indicator light flashes (if the valve is in the open position, the flashing is weak).
   4. Open the mobile app.
   5. Tap on + to add a new product.
   6. Tap on Auto Scan to find the new product.
   7. Wait for the auto scan function to list the product.
   8. Follow the on-screen instructions to add the product.
   → You have added the product to the mobile app.
   → You have connected the product to the Wi-Fi network.

10.3 Operating and controlling
Use the mobile app to remotely operate and control the product.

Opening and closing the valve

1. On the screen Home, touch the On/Off button to open and close the valve.
   → (If the valve is open) the On/Off button is green.
   → (If the valve is open) the indicator light on the product is on.

Note:
In normal operation, the valve is always in one of two states: fully closed or fully open.
Setting the default restart status
The default restart status defines if the valve opens or closes when power is re-established after a power failure.

1. Open Setting.
2. Set the default restart status: close (valve closes), open (valve opens).
3. Confirm the settings.

Emergency operation

During a power failure the valve cannot be opened or closed. Release the gear by the gear release mechanism and open and close the valve manually.

WARNING
Motor runs if gear is released with power supplied.
Moving parts can trap and squeeze body parts.

• Disconnect power before releasing the gear.

1. Disconnect the power supply. In case power is re-established the motor will not run.
2. Pull the ring on the gear release mechanism to release the motor.
3. Open or close the valve manually.
4. Reconnect the power supply.

Important:
When the power supply is re-established, the valve will open or close according to the Restart status setting in the mobile app.

Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.

1. Disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.

• Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads
  Enter the product item number in the search box. You can then download the EU declaration of conformity in the available languages.

Technical data

15.1 Valve requirements
Outer valve/pipe diameter Ø………. min. 12.7 mm (½”), max. 31.75 mm (1¼”)
Break-To-Open torque (BTO)…….. max. 5.88 Nm
End-To-Close torque (ETC)……….. max. 5.88 Nm
15.2 Valve drive
Input ……………………………………… 12 V/DC, 1 A
Torque ……………………………………. max. 5.88 Nm
15.3 Power adapter
Input ……………………………………… 100 – 240 V/AC, 50/60 Hz, 0.4 A
Output ……………………………………. 12 V/DC, 1A
15.4 Wi-Fi module
Wi-Fi standard ………………………… IEEE 802.11b/g/n, 2.4 GHz
Wireless frequency ………………….. 2.400 – 2.484 GHz
Wi-Fi range …………………………….. max. 100 m (open space)
Wi-Fi transmission power …………. 16 dBm
15.5 Environment
Operating temperature …………….. -10 to +50 °C
Operating humidity ………………….. < 95 % RH (non-condensing)
Storage temperature ………………… -10 to +50 °C
Storage humidity ……………………… < 95 % RH (non-condensing)
15.6 Other
Dimensions (W x H x D) (approx.) 100 x 150 x 70 mm
Weight (approx.) ……………………… 310 g

www.conrad.com/downloads

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2446222_V1_1021_jh_mh_en I1/O1

References

• Conrad Electronic » All parts of success
• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>