ecler KICK-SB28 professional Audio and Video Solutions Loudspeakers User Manual

ecler KICK-SB28 professional Audio and Video Solutions Loudspeakers

USER MANUAL

MODEL: KICK-SB28

1. PRECAUTIONS

1.1 Important Notice

The flashing light with an arrowhead symbol inside an equilateral triangle on it is intended to alert the user of the presence of non-insulated “dangerous voltage” within the enclosure, which might be of sufficient magnitude to pose a risk of electric shock to users.

The exclamation mark within an equilateral triangle is intended to alert the user of the requirement for important operating and maintenance (servicing), for which instructions may be found in the literature accompanying the appliance.

WARNING (If applicable): Terminals marked with symbol “ ” may be of sufficient magnitude to pose a risk of electric shock. The external wiring connected to terminals requires installation by a technician, or the use of ready-made leads or cords.

WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or humidity.

WARNING: A device with Class I manufacturing ought to be connected to a mains socket outlet with a protective earthing connection.

WARNING: Ecler products have a long lifetime of more than 10 years. This product must never be discarded as unsorted urban waste, but must be taken to the nearest electrical and electronic waste treatment centre.

1.2 Key Safety Directions

1. Read the following directions.
2. Keep the following directions.
3. Heed all warnings.
4. Follow all directions.
5. Do not use this device in proximity to water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that may release heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades, being one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, contact a qualified electrician for a replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles, and at the point of exit from the device.

11. Only use attachments/accessories specified by the manufacturer.
12. Unplug the device during lightening sorts or when unused for long periods of time.
13. Refer all servicing to qualified personnel. Servicing is required when the device has been damaged in any way, such as power supply cord or plug damage, liquid spillage or objects onto the device, the device has been exposed to rain or humidity, does not operate normally, or has been dropped.
14. Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket, therefore, it should always remain easily accessible
15. Equipment is connected to a socket-outlet with an earthing connection by means of a power cord.
16. The marking information is located at the bottom of the unit.
17. The device shall not be exposed to dripping or splashing liquids, and no liquid-filled objects, such as a filled up glass, shall be placed on top of the device.

1.3 Cleaning Directions

Clean the unit with a soft, dry clean cloth or slightly wet with water and neutral liquid soap only, then dry it with a clean cloth. Be careful that water never gets into the unit through any hole. Never use alcohol, benzine, solvents or abrasive substances to clean this unit.

NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be caused to people, animal, or objects due to failure to comply with the warnings above.

2. WARRANTY & ENVIRONMENT

Thank you for choosing our Ecler KICK-SB28!

We greatly value your trust.

It is VERY IMPORTANT to carefully read this manual and to fully understand its contents before any connecting takes place in order to make the best use of this equipment, as well as to get the best performance from it.
To ensure optimal operation of this device, we strongly recommend that its maintenance be carried out by our authorised Technical Services.

All ECLER products are covered by warranty, please refer to www.ecler.com or the warranty card included with this product for the period of validity and conditions.

Ecler is truly committed with the environment and planet sustainability, energy saving and CO2 emission reduction. Recycling materials and using non- contaminant components are also top priorities in our green crusade.

Ecler has deeply evaluated and analyzed the environmental impacts of all the processes involved in the production of this product, including packaging, and has alleviated, reduced and/or compensated for them.

3. PACKAGE CONTENTS

• 1 x KICK-SB28.
• 1 x Speakon® 4C
• 4 x Rubber foot (screws included).
• 1 x Wall support system (screws not included).
• First Steps Guide.
• Warranty card.

4. DESCRIPTION & FEATURES

KICK-SB28 is a wooden subwoofer reinforcement cabinet with and long-term reliability, weather protected IP46 rated, featuring 700 WRMS @ 4Ω. His versatility allows you to place in horizontal or vertical position, even install in the wall with the included bracket. It features 2×8” woofers perfectly positioned to maximize the low frequency response while reducing the vibrations on the acoustic enclosure.

4.1 Main Features

• 700W (RMS) Outdoor passive subwoofer.
• 2×8” water resistant treated woofers.
• Vibration free.
• 18mm Plywood birch with Polyurea coating enclosure material.
• Weather-protected with IP46 rating
• Rubber feet for floor installation, either vertical or horizontal included.
• Wall bracket included for wall-mounted.

5. CONNECTIONS

The connection cables which connect the amplifiers output and the speaker should be of good quality, have sufficient conductor area and be as short as possible. The latter fact is especially important when the distance is long and the load impedance low (4Ω). A cross-section of at least 2.5mm2 is recommended for distances up to 10m; 4 or 6mm2 for longer distances. Following formula gives the required section, assuming 4% losses:

Cross section in mm2 = Length in m/ Loudspeaker impedance in Ω

• Always respect the polarity. The loudspeaker has an Speakon® 4C connector.
• See detailed connections diagram on next page.

5.1 Connection Diagram

6. EQ SETTINGS

Download the Ecler Loudspeakers EQ Settings file ready to import in EclerNet Manager software.

7. RECOMMENDED AMPLIFIER

The output power of the recommended amplifier for KICK-SB28 is 1400W RMS.

8. POSITIONING & INSTALLATION

8.1 Positioning

Consider following general rules:
Place the speakers on a solid and firm surface. Subwoofers placed directly and horizontally on the ground have a higher output than hanged or directly on the floor, but vertically. No obstacles should stand between the enclosures and the audience.

Download all EASE files by clicking on the image:

8.2 Installation

8.2.1 Horizontal Mount

8.2.2 Vertical Mount

8.2.3 Wall Mount

9. TECHNICAL DATA

9.1 Technical Specifications

KICK-SB28

SYSTEM|
---|---
Effective Freq. Range 1| 33Hz-1.6kHz  (-10dB)
Power handling| 700W RMS / 2800W Peak
Sensitivity 2| 92 dB (1W/1m)
Maximum SPL 3| 120dB continuous  / 126dB peak
Recommended amplifier power| 1400W RMS
TRANSDUCERS|
Ways| Subwoofer
Driver| Water resistant Treated Paper Cone
Low frequency driver| 2 x 8″  woofer
Nominal impedance| 4Ω
FILTERS|
Crossover filter| No
Recommended High-Pass protection filter| 60 Hz with minimum 12 dB / octave filter
PHYSICAL|
Connection type| 1 x Speakon® 4C
Installation options| Surface, Wall mounting
Environmental| IP46 rated
Enclosure material| 18mm Plywood birch with Polyurea coating
Grille material| Aluminium
Grille fixing system| Screws
Operating temperature| Min: -10°C ; 14°F
Max: 40°C ; 104°F
Operating humidity| <85% HR
Storage temperature| Min: -10°C ; 14°F
Max: 40°C ; 104°F
Storage humidity| <90% HR
Included accessories|    4 x Rubber foot (screws included)
1 x Wall support system (screws not included)
Finished colour| Black (RAL 9005)
Dimensions (WxHxD)| 660 x 450 x 250 mm  / 25.98 x 17.72 x 9.84 in.
Weight| 23Kg  /  50.7lb
Pieces per box| 1
Shipping dimensions (WxHxD)| 750 x 550 x 350 mm  /  29.52 x 21.65 x 13.77 in.
Shipping weight| 28Kg / 61.72lb

1. Below the sound pressure level at specified sensitivity
2. Measured on-axis, far field and referenced to 1 meter by inverse square law. Average from 100 Hz to 10 kHz.
3. Calculated from sensitivity and power handling specifications, exclusive of power compression

9.2 Mechanical Diagram

All measurements are in mm.

All product characteristics are subject to variation due to production tolerances. NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications.

For technical queries contact your supplier, distributor or complete the contact form on our website, in Support / Technical requests.
Motors, 166‐168 | 08038 Barcelona, Spain | (+34) 932238403 | information@ecler.com | www.ecler.com

FAQ

Q: How do I clean the subwoofers?

A: Use a dry cloth to clean the exterior of the subwoofers. Do not use any liquid cleaning agents.

Q: What should I do if the subwoofers are not functioning normally?

A: If the subwoofers are not operating as expected, refer servicing to qualified personnel. Do not attempt to repair the product yourself.

Q: Can I use the subwoofers near water sources?

A: It is not recommended to use the subwoofers in proximity to water sources to avoid any electrical hazards.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>