KINGrinder K6 Coffee Grinder Instructions

Table of Contents

Product Specifications

Model: K6
Included in the Box:
- Grinder
- Handle
- PC Lid with Black O-ring
- White O-ring & Circlip Brush

Operating the Grinder

Gently rotate the adjustment nut clockwise to number 0.
Rotate the adjustment nut counterclockwise to the recommended grinding clicks (Refer to the table below).
Place 30~35g of coffee beans in the grinder.
Attach the handle and start grinding.

Recommended Grinder Settings

Cleaning the Grinder

Disassemble by rotating the adjustment nut anti-clockwise and removing components in order.
Reassemble in the correct order ensuring proper placement of components.

Assembling PC Lid and Handle

Remove the black O-ring from the PC lid and insert the white O-ring.
Ensure the correct installation of the white O-ring in the handle’s groove for proper fixation.

Using Electric Power

Prepare an electric screwdriver with 15~25Nm torque and a 6.35mm(1/4 inch) Hex Shank.
Install the black O-ring on the PC lid.
Insert the bit holder into the center shaft, grasp firmly, and apply power gradually.
Slow down the grinding speed to prevent damage to the central shaft.

Precautions

Frequently Asked Questions (FAQ)

Q: Can I wash the entire grinder with water?
A: No, it is recommended to use a brush for cleaning and avoid washing with water.
Q: Can I dismantle the exterior burr for cleaning?
A: It is advised not to dismantle the exterior burr for precision reasons.

Gently rotate the adjustment nut clockwise until it stops at number 0. The number 0 is the correct zero position, do not over-tighten it past the number 0.
Rotate the adjustment nut counterclockwise to the recommended grinding clicks (Please refer to the table below).
Place 30~35g of coffee beans on the grinder.
Place the handle on and start grinding.

Brewing methods/K6

Disassemble:

Rotate the adjustment nut anti-clockwise for three or four rotations.
Holding the burr set while removing the circlip.
Take out the components in order. The burr set (attached with the central shaft), the bearing cover, and the spring from the burr set. The top bearing cover and the top bearing from the above. In this state, do not rotate the adjustment nut as it is an unnecessary step.

Assemble:

Put the components in order. Place the spring and the bearing cover into the burr set and install the burr set back to the grinder.
While holding the burr set, place the top bearing and the top bearing cover. Note that there are two shapes of the top bearing cover: flat design & curved design. Ensure that the curved design of the top bearing cover faces upward.
Slide the circlip onto the top bearing cover while still holding the burr set.

Take out the black O-ring from the groove on the PC lid.
Insert the provided white O ring.
Ensure that the white O-ring is correctly installed into the groove on the handle for proper fixation.

You need to prepare:

Electric screwdriver at a 15~25Nm torque.
6.35mm(1/4 inch) Hex Shank.
Take out the handle and install the black O-ring to the PC lid.
Ensure that the bit holder is fully inserted into the center shaft, grasp the grinder firmly, and gradually apply power.

Slow down the grinding speed to prevent damage to the central shaft.

The entire grinder should not be washed with water. Please use the brush for cleaning.
Do not rotate the handle when the grind setting is at 0 or below 15 clicks, as this could damage the burr set.
For precision reasons, do not dismantle the exterior burr. Avoid forcefully disassembling the grinder with tools.
Only grind coffee beans. Do not grind unroasted coffee beans.
Avoid spraying water directly onto any part of the grinder. You can perform RDT by spraying water on another object.
Avoid second grinding as the coffee fine powder may block the parts.
Please store in a dry environment.