SKAN HOLZ 602155 Faro 300 x 250cm Natur Instructions
- August 19, 2024
- SKAN HOLZ
Table of Contents
SKAN HOLZ 602155 Faro 300 x 250cm Natur
Important information
We are pleased that you have chosen a product of SKAN HOLZ. Please check the construction set for completeness using the position list in good time before starting con-struction or commissioning your construction team. If individual parts are defective or missing, we will deliver these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a construction company.
Please understand that we cannot assume any guarantee for the following defects:
- incorrect storage before assembly
- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)
- damage due to erection errors, e. g. the house is not level or not right-angled
- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of the roof by removing the snow layer
- storm damage (insurance cases) or violent destruction
- damage through any alteration to the design by the client
- natural formation of cracks, branch holes, twisting, decoloration, or similar modification (natural process; does not influence the statics)
Storage information until construction
- store pallets on a level and dry surface.
- Protect from exposure to sunlight and the influences of weather; wood can warp drastically in a loose condition!
Maintenance tips
The wood is untreated. Accordingly, regular, protective coating is
necessary! Please observe the attached information sheet “Care
instructions/Colour treatment”.
General tips and refer to
- The packaging foil can be used to keep moisture out of the house. It is laid according to the ground area of the house under the main bearing.
- Given that the roof is constantly exposed to the weather, a covering with only one layer of roofing paper will not be enough over the long term. An additional covering with bitumen shingles, alternatively with a material of at least equivalent quality, must follow. We recommend clearing the roof during heavy snowfall!
-
Foundation according to the structural calculations (not included in the scope of delivery): concrete C25/30, each 2 Ø 12 top and bottom, brace mat R188A (alternatively brace Ø 6/20cm). Anchoring of the floor beams
(in the building) on the strip foundation using bolts M12, e < 60cm. The base bearings in the storeroom of the house must be entirely flush. -
The thread rods to secure the house against storm are secured at the top with a washer and a nut, from below with a washer, spring, and nut to tighten the upper nut of the thread rod without any problem, the spring at the bottom should be pressed upwards with the thread rod. The spring may only be tightened slightly so that the house can work at the top. The projecting ends of the thread rods have to be cut off at the top. Even after the house has been completed, attention must always be paid to the fact that the thread rods are not seated on the floor as otherwise when it is dry, gaps can arise and the roof is pressed upwards. Tip: the thread rods can also be pushed subsequently into the bores. You have to make sure that each plank has a bore and that these are free and not blocked by shavings or similar.
-
In case of varying weather conditions, the wood alters in height (due to ‘working’). To avoid the formation of joints, the planks of the house may not, for example, be joined to one another through several block planks as then the wood can no longer expand.
-
The door and window frames may not be bolted to the wall above the first supporting plank since the individual bolts will work in height. If the door does not close correctly, this can be readjusted by rotating the hinges in the door leaf and door frames.
WHAT IN THE BOX
General idea
Additional
OVERVIEW
DIMENSION
ASSEMBLY INSTRUCTION
Instructions for maintenance/color treatment
Care instructions for articles made of
- Solid structural timber, softwood, and laminated wood, untreated The wooden parts of the kit are untreated, so a regular protective coating is essential.
Recommendation:
An initial coat on all sides with a wood primer (protection against fungi and
insects), and then one coat each of intermediate and top coat with a high-
quality wood-preserving varnish (color tones, UV protection, protection
against weathering).
The following applies to wood panel cabins:
The initial and intermediate coats must be applied before assembly. Please
ensure that the wood panels have dried before construction. The top coat is
applied after construction. Regular varnishing is necessary to maintain the
wood. Make sure the products are given good UV protection and that the working
guidelines of the varnish manufacturer are observed.
- Douglas fir, untreated If kits are constructed from Douglas fir without additional chemical impregnation, the material requires no further care apart from regular cleaning with water of the patina that forms.
Recommendation:
If the wood stain is to be fixed, we recommend an initial coat on all sides
with a wood primer (protection against fungi and insects), and then one coat
each of intermediate and top coat with a high-quality wood preserving varnish
(color tones, UV protection, protection against weathering). Regular
varnishing is necessary to maintain the wood. Make sure the products are given
good UV protection and that the working guidelines of the varnish manufacturer
are observed.
- Softwood, impregnated The wood has already received an initial immersion treatment with a water-based impregnation. This protects the wood against fungal and insect infestation.
Recommendation:
The surface should be treated again after 2–3 sunny months at the earliest and
should feel dry. Clean the surface before treating. We then recommend one coat
each of intermediate and top coat with a high-quality wood preserving varnish.
Regular varnishing is necessary to maintain the wood. Make sure the products
are given good UV protection and that the working guidelines of the varnish
manufacturer are observed.
Special care instructions for color-treated products (SKAN HOLZ)
The color-treated parts of our kits are treated with high-quality varnish.
In the area where it is applied this has the following properties:
- protection against blue stain fungi
- protection against damage caused by UV radiation
- no flaking
- reduces swelling and shrinking
- Let wood grain shine through
- thin layer
Information on construction
- Each color-treated kit comes with a container of varnish for repairs. Please stir thoroughly before use.
- Untreated cut edges must be treated twice with this varnish before assembling the building element.
- All screw holes or other damage to the wood surface of color-treated parts caused by assembly must also be treated at least twice with varnish during construction.
- On-site, the surface can be further refined by sanding it again with fine-grained sandpaper and giving it another coat of paint. The following also applies in particular to color-treated houses:
- In the kit, the wall panels, as well as the door and windows on the exterior, have been color-treated on one side
- All parts of the kit that are untreated and mounted on the outside (e.g. exterior overhanging soffits or purlins, as well as the inside of the door and windows) are unprotected and need to be subsequently treated on-site with primer and at least once with varnish. Once again, follow the instructions of the varnish manufacturer.
Maintenance:
- The wood surface has to be examined at regular intervals for damage (at least once a year). Any damage or drying cracks that have appeared must be repaired immediately.
- Painting/varnishing needs to be undertaken as a long-term care measure to protect the surface. The required frequency depends on the location and the conditions the surface is exposed to and must commence before the damage becomes visible.
Please note that the printed color samples are not binding. Variations in color are possible. Storage marks on building components that are color- treated on all sides are due to technical reasons.
- Please read it carefully and keep it in a safe place!
- ©SKAN HOLZ Europe GmbH, Im Alten Dorfe 10, 21227 Bendestorf / Germany / info@skanholz.com / www.skanholz.com Technische Änderungen vorbehalten. Stand 03.2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>