SKAN HOLZ Ostende 2 Log Cabin 400 x 300 cm Installation Guide

: September 28, 2024
: SKAN HOLZ

Table of Contents

SKAN HOLZ Ostende 2 Log Cabin 400 x 300 cm
Product Information
Usage Instructions
Important information
Storage information until construction
Maintenance tips
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SKAN HOLZ Ostende 2 Log Cabin 400 x 300 cm

Product Information

Specifications

Model: Ostende 2
Dimensions: 400 x 300 cm
Available Colors: 603701 (untreated), 603701-13 (slate gray), 603701-15 (Swedish red)

Usage Instructions

Storage Information

Store pallet on a level and dry surface.
Protect from exposure to sunlight and weather to prevent wood warping.

Maintenance Tips
Refer to the attached Care Instructions/Colour Treatment information sheet for maintenance guidance.

General Tips

Use packaging foil to keep moisture out by placing it under the main bearing of the house.
Consider adding an additional welding line for extra weather protection. Clear the roof during heavy snowfall.
If the door does not close correctly, adjust by rotating the hinges in the door leaf and frames.

FAQ

Q: What should I do if I find defective or missing parts in the construction set?
A: Contact us immediately, and we will deliver the necessary parts as quickly as possible to avoid construction delays.
Q: How should I protect the wood from warping?
A: Store the pallet on a level and dry surface away from sunlight and weather exposure.
Q: How can I adjust the door if it does not close correctly?
A: Rotate the hinges in the door leaf and frames to readjust for proper closure.

Ostende 2 400 x 300cm

Important information

We are pleased that you have chosen a product of SKAN HOLZ.
Please check the construction set for completeness using the position list in good time before starting construction or commissioning your construction team. If individual parts are defective or missing, we will deliver these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a construction company.

Please understand that we cannot assume any guarantee for the following defects:

incorrect storage before assembly
incorrect anchoring with the ground or inadequate foundation (foundation according to statics)
damage due to erection errors, e. g. the house is not level or not right-angled
damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of the roof by removing the snow layer
storm damage (insurance cases) or violent destruction
damage through any alteration to the design by the client
natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural process; has no influence on the statics)

Storage information until construction

store pallet on a level and dry surface.
Protect from exposure to sunlight and the influences of weather; wood can warp drastically in a loose condition!

Maintenance tips

Please observe the attached information sheet “Care instructions/Colour treatment”.

General tips and refers to

The packaging foil can be used to keep moisture out of the house. It is laid according to the ground area of the house under the main bearing.
As the house is exposed constantly to the weather, it is necessary to lay a further welding line. You have to make it for your own. We recommend clearing the roof during heavy snowfall!
1. Foundation according to the structural calculations (not included in the scope of delivery): concrete C25/30, each 2 Ø 12 top and bottom, brace mat R188A (alternatively brace Ø 6/20cm). Anchoring of the floor beams (in the building) on the strip foundation using bolts M12, e < 60cm. The base bearings in the storeroom of the house must be entirely flush. The wooden parts of the building kit are delivered with a residual moisture content of about 15%.
2. Wood “works”! This means that the wooden parts will swell during prolonged damp weather and shrink (dry out) during prolonged dry periods. This only occurs in height or width, not lengthwise. The block planks are firmly screwed to the vertical corner post during installation. This will not change its length, but the horizontally attached planks change their height. If damp weather persists, the block planks can swell slightly after completion. It is therefore important to leave 1mm clearance between the planks when fitting. Use the enclosed spacer (to avoid unnecessary strains in the structure).
3. If the door does not close correctly, this can be readjusted by rotating the hinges in the door leaf and door frames.

Ostende 2 400 x 300cm

General idea

Additional