Danfoss AB024D Solenoid Coil Installation Guide
- August 17, 2024
- Danfoss
Table of Contents
Danfoss AB024D Solenoid Coil
Specifications
- Product Name: Solenoid Coil Type AB, AM, AC, AK, AL, AP, BB, BA, BC, and BD
- Model Number: 042R9019
- Manufacturer: Danfoss
- Class of Protection: Class I
- Control Type: Spade
- Operating Temperature: Ambient temperature, refer to Tambient on the coil
- Voltage Variation: Refer to print on coil
Product Usage Instructions
- Installation Guide
- Follow the steps below to install the solenoid coil:
- Identify the type of coil required based on the model number.
- Connect the appropriate spade connectors to A1 and A2 for the IP65/PD3 Cable plug for A – Coils.
- For B – Coils, connect B1 and B2 with IP65/PD3 and B3 with IP67/PD4 Cable plug.
- Ensure proper insulation and connection according to the provided specifications.
- Maintenance
- To maintain the solenoid coil, follow these guidelines:
- Check for any signs of wear or damage regularly.
- Clean the coil and surrounding area from any dust or debris that may affect performance.
- Ensure all connections are secure and insulated properly.
FAQs
- Q: What is the voltage tolerance for the solenoid coil?
- A: For voltage tolerances, refer to the datasheet provided when ordering the coil.
- Q: Where can I find information for UK customers?
- A: For UK customers, contact Danfoss Ltd. at 22 Wycombe End, HP9 1NB, GB.
INSTALLATION INSTRUCTION
Solenoid coil
Type AB, AM, AC, AK, AL, AP, BB, BA, BC and BD
| Type of control | 1 |
|---|---|
| Class of protection | Class I |
| Ambient temperature | See Tambient on coil |
Voltage variation
Voltage tolerances
| For voltage variation, see the print on the coil For voltage tolerances see
the datasheet when ordering the coil
Humidity| Only none-conductive pollution occurs except that occasionally a
temporary conductivity caused by
condensation is to be expected.
Ball pressure test| 200 °C (392 °F) in accordance to IEC 60695-10-2
Impulse withstand voltage
| Spade
Plug Plug
| 4.0 kV at altitude <4000 m (13123 ft)
4.0 kV at altitude <2000 m (6561 ft)
3.1 kV 2000 m<altitude<4000 m (6561<altitude<13123 ft)
Overvoltage category| III
Degree of protection IPxx
Pollution degree PDX
| Enclosure rating according to IEC standard 60529 (See illustration for details A-B)
Pollution degree according to EN60664-1 (See illustration for details A-B)
Installation
| Integrated control Incorporated control
Independently mounted control (IP65/IP67)
Suitable cable,
Conductor size for plug
| ø6.6 – ø11 mm (ø0.26 – ø0.43 in)
0.75 – 1.5 mm² (21 – 15 AWG flexible cord)
Suitable cable for cable plug| See the datasheet when ordering the coil
Cable conductor size| 3 x 0.75 mm² (3 x 0.001 in2)
Plugs can be removed/Mounted| 10 times
Surface temperature| Independently mounted controls must be inaccessible in
normal use if the surface temperature on the control is> 85°C
- Only qualified personnel are allowed to install or maintain this product
- Disconnect the power when dismounting the coil
- Avoid direct exposure to alkaline conditions, use in neutral conditions is recommended
- Ensure that the O-ring is in place on the valve
- If the coil is used as an independently mounted control, the end-user shall use a plastic cable gland with strain relief
MORE INFO
- Visit www.products.danfoss.com for further technical data.
References
- Danfoss Global Product Store | Homepage
- Danfoss Spain Product Store | Homepage
- Danfoss France Product Store | Homepage
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>