saxby lighting 108870 Dual Wattage Tri CCT Gloss White LED Batten Instruction Manual

: August 16, 2024
: saxby lighting

Table of Contents

saxby lighting 108870 Dual Wattage Tri CCT Gloss White LED Batten
Product Usage Instructions
Layout
Installation
Wiring
Mechanical structure
Dimensions
Wiring Diagram
Technical Data
Dial code setting
Detection Patterns
Performance
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 108870 Dual Wattage Tri CCT Gloss White LED Batten

Specifications

Supply Voltage : 220-240 V~, 50 Hz
Bulb Type:
- 108870: 31.5W / 20W LED (SMD) CCT, 3000/4000/6000K
- 108871: 39W / 26W LED (SMD) CCT, 3000/4000/6000K
- 108872: 44W / 35W LED(SMD) CCT, 3000/4000/6000K
Energy efficiency class C
Non-replaceable light source
Replaceable control gear by a professional
For indoor use only
Emergency power: 1W (Battery)
Battery warranty: 5 years

Product Usage Instructions

Layout:
This product is Class 1 and must be connected to earth. Ensure the mounting surface is flat and smooth for a good fit.

Installation:

Remove existing fittings completely.
Turn off the power switch before installation.
Identify the wiring from the existing light fitting and connect it to the product following the wiring diagram.
Choose the wattage and color using the wattage switch or CC T switch on the driver before installation.

Wiring:
This product is Class I and must be earthed. Follow the wiring instructions provided in the manual for both maintained (unswitched) and maintained (switched) wiring.

Changing Wattage and Color:
Before changing the wattage or color, ensure the power switch is turned off for safety.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning
This is a Class 1 product and must be earthed. Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Check the pack and make sure you have all the parts listed. Install in accordance with the IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a fused circuit. If replacing an existing fitting, make a careful note of the connections. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross section area of 1.0mm 2 . Cables must be protected using suitable conduit or plastic trunking. Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation. This product can be installed on the ceiling or wall.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

Note that the switch is turned off before installation. The mounting surface must be flat and smooth to ensure a good fit.

The wattage is changeable by using the wattage switch on the driver

The colour is changeable between 3000/4000/6000K using the CCT switch on the driver before installation. Choose your preferred wattage and colour before installing by wattage switch or CCT switch on the driver.

Note : Befeore you change the wattage or colour, please turn off the power switch for safety.

Hold the product in place and mark the position of the fixing holes. This may require the help of an assistant. If wall mounting, ensure that the product is level.
Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for bricks, cavity walls or plasterboard.
Ensure the ceiling or wall is capable of holding the weight of the product and then fix brackets in place.
Rotate both ends of the product in the direction of the arrow to open the diffuser cover.
Pull the supply cable through the middle grommet and fix the light fittinginto position using appropriate fixings.
Connect the supply cable to the quick fit terminal block as detailed wiring diagram.
Close diffuser cover into place.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Wiring

This product is Class I product must be earthed. Having correctly identified the wiring from your existing light fitting and connected to the connection block inside the product in the following way: Under the master slave mode, when maintaining the slave lamps, turn off the supply of both ends of the Master.

To avoid the risk of electric shock.

Maintained(Unswitched) Wiring :
The product on permanently and comes on during a power failure

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Microwave Movement Sensor

DETACHED SENSOR ON/OFF FUNCTION

220-240VAC Input, ON/OFF Function
Special Detached Design For More Applications
DIP Switch Control, User Friendly
5 Years Warranty

Mechanical structure

Dimensions

Unit : mm

Wiring Diagram

Shown-part length about 335mm

Technical Data

Dial code setting

Detection Patterns

Performance

Daylight Disable
When daylight threshold is preset as “disable”, the sensor turns light ON when motion gets detected, and Ort after holdtime

The sensor turns light ON when motion gets detected.
The sensor keeps light ON for holdtime period after motion leaves.
The sensor turns OFF light automatically after the holdtime.

Installation precautions

Microwave sensor can be installed in any lamp except the one with full metal shell.
The detected surface cannot be shielded by metal objects.
Make sure the microwave module is completely exposed outside.
The detection surface of the sensor module shall be installed facing the detection area.
Should be kept away from the driver to avoid interference generation and lamp flashing.
Wiring must be strictly in accordance with the wiring diagram to avoid short circuit.

User Notes

Microwave can penetrate walls or glass thinner than ＜20mm and attenuate if thicker than ＜20mm.
The driver voltage shall be stable and float within 10%.
Detection area will be affected by speed of motion, mounting height and movement volume.
Conduct test on sunny days without the lampshade which will affect the tested lux value.
3M distance is suggested when having a lot sensors in one same room.
If the sensor is applicated in the room with 5G WiFi router, 3M distance or above is needed.

Application Environment

Suitable for indoor installation to avoid false triggering due to external factors such as rain, wind or tree swing.
Shall not be installed in the place with all four metal shelters and small space (such as galvanized-iron roof).
Shall note be mounted installation, so as to avoid false trigger caused by the lamp itself shaking.
Shall not be installed next to large operating machines such as ventilator/ceiling fan to avoid false triggering caused by machine vibration.
The sensor might be unwanted triggered in rooms that are small, or mostly filled with metal materials; please try to decrease sensitivity when it happens or contact us for support.

Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting- info.co.uk/108870

V4 24/01/2024