momax BR10 Pinpop Lite Locator Instruction Manual
- August 15, 2024
- MOMAX
Table of Contents
momax BR10 Pinpop Lite Locator
Product Usage Instructions
Installation:
- Pull out the product from the packaging.
- Remove the protective covering before use.
- Place the product on a stable surface.
Operation:
- Press the designated button to activate the product.
- Follow the on-screen instructions for further operation.
Maintenance:
- Clean the product regularly with a damp cloth.
- Avoid exposing the product to extreme temperatures or moisture.
FAQs
Q: Is the device safe for use in all environments?
A: Yes, the device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.
Q: How do I charge the device?
A: Use the provided charging cable and connect it to a power source. Follow the instructions in the user manual for charging details.
Q: Can the device be submerged in water?
A: No, the device is not waterproof. Avoid exposing it to water or other liquids to prevent damage.
Apple, Apple Find My, Apple Watch, Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are trademarks of Apple Inc. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Overview
INSTRUCTION FOR USE
The device is powered on and enters the pairing state
- When using it for the first time, please tear off the protective film on the surface of the product
- Pull out the insulating paper, and hear the sound of “dropping”, indicates that the product has entered the pairable state.
- If the insulating paper is difficult to pull out, you can use the white disassembling piece to open the case, remove the white disassembling piece and place it on the battery cover, rotate the rear cover counterclockwise to open the battery cover and remove the insulating tab and put it back on the battery the way it was intended to be, and then slide the battery cover clockwise to close it completely.
Find and bind your product
Please make sure that you have an iPhone, iPad, or iPod touch with iOS 14.5 or
iPadOS 14.5 or later and two-factor authentication enabled.
- Turn on【Bluetooth】 on your Apple device, and go to【Settings】 -【Privacy & Security】 – Turn on 【 Location Services】 and swipe down and tap 【FindMy】 to allow access to the location and turn on 【Precise Location】.
- Goes back to the main screen of the Apple device, click the the【FindMy】 app, and then select the 【Item】 tab.
- Click 【+】, and then click 【Add Other Items】.
- Find the item name “MOMAX BR10”, click 【Connect】, fill in the “Name Item” custom product name, and click【Continue】”Choose an emoji”, click to continue to show “This item is linked to your Apple ID”, please check that the email address and mobile phone number are correct, then tap 【Agree】, and then tap 【Finish】 to add successfully.
SETUP THE LOST MODE
- When the base station is a certain distance away from the console, you need to turn on the lost mode to mark the item as lost. Tap Item at the bottom of the screen, then tap the name of the missing item. Under Lost Mode, tap Enable.
- Follow the on-screen instructions and enter a phone number where you can be contacted, or if you want to enter an email address instead, tap Use email address. Then press Enable.
Note:
Please make sure to allow notifications from the Find My app first.
View the locator location on the map
- Open the Find My app, then click the Items tab. Select the locator you want to locate in the Items list. If the locator is within the coverage area of your device or the Find My network where the locator was recently detected, you can see it on the map. Below its name, you’ll see the location and time of the update.
- If the base station is not within range of your device or any device on the Find My network, you can see its last known location and time. If you want to receive notifications when the tracker comes within range of your device or can be detected by the [Find My] network, please turn on [Notify when found] under [Notifications].
PLAY A SOUND
- Open the 【FindMy】app, select the 【Item】tab, and click the product you need to use, the mobile phone interface will display the the【Play Sound】button, click the 【Play Sound】button, and then you will hear a piece of music, indicating that the product can be used normally.
- When the device and the product are out of distance, the【Find My】app cannot connect to the product and the product cannot play sound normally.
Prevent unauthorized tracking
- If any of the locators and other Find My network accessory products leave their owners and move with you for a while, you can send a notification to your Apple through the Find My app device, and be able to observe the walking path as you move and in time.
- These features are designed to prevent people from trying to track you without your knowledge, so if you feel your safety is at risk, contact your local law enforcement officer*.
- This product has a function to prevent unauthorized tracking, and should not be used to track others, nor should it be used to track property that does not belong to you. In many countries and regions around the world, it is an offense to use these products to track someone without their consent.
REPLACE THE BATTERY
- Take out the white triangle “white disassembling piece” that comes with the package.
- Locate the slots on the back of the product.
- Take the white disassembling piece and place it in the slot on the back of the product, rotate counterclockwise to open the back cover.
- Remove the battery, replace it with the prepared new battery “CR2032 3V” and install the battery, after installing the battery, you can hear the product emit a “drop” sound, which means that the battery has been successfully replaced, and then place the lower cover in the rotating groove of the product, and rotate the back cover with the disassembling piece clockwise, so that it remains closed. Then place the lower cover at the rotating slot of the product and turn it clockwise with the disassembling piece to keep it closed.
Except for the disassembly tool, any knife and screwdriver are not recommended as auxiliary tools to avoid damaging the product shell or appearance.
PRODUCT RESET
- When you need to replace/unbind the product bound to your Apple device, in the 【Find My】 app, in the 【Item】 tab, find the product that needs to be unbound, slide to the bottom of the page, click 【 Remove Item】, click 【Remove】, and click 【 Remove】 again to confirm that the product is no longer available in the 【Item】 tab.
- Repeat the above steps of “replacing the battery”, take out the battery, put in the battery, and hear a “Di” sound. After repeating the operation 5 times, a “Di Di” sound will be emitted when installing the battery, indicating that the product has been reset and is ready to connect to a new device.
- If you are unable to use the base station, make sure the product is ready to be set up, remove and replace the battery, place the base station close to the portable device you want to connect to, or reset the product before attempting to connect the base station.
- If you physically reset the product before unbinding, it will take longer for the Apple device to remove the product.
SPECIFICATION
MODEL: BR10
- Battery: CR2032
- Bluetooth version: BLE 5.3
- Material: ABS
- Size: 40.5x32x9mm
- Weigh: 8g±2g
- Compatibility: Compatible with Apple devices only; iPhone and iPod touch models with iOS 14.5 or later; iPad models with iPadOS 14.5 or later; iMac and MacBook with macOS 12.5 or later.
CONTAINS:
- Pinpop Lite Find My Locator
- Adhesive sticker x 10pcs
- Opener
- Hanging strap
- Instruction manual and warranty card
SAFETY WARNING
- Do not dismantle or modify the product;
- Do not store the product in wet conditions;
- Do not keep or use the product near heat sources;
- Do not let water or any other liquid flow into the inside part of the product’s interface. This would cause damage to the product;
- Avoid direct sunlight. Keep away from heat source;
- Avoid high processor load in long-running loops or while charging;
- Ensure good ventilation while using;
- In case of overheating, stop using the product.
DISPOSAL OF ELECTRONIC PRODUCTS
- Do not place the product as household waste;
- Please dispose of discarded electronic products properly according to local regulations.
- MOMAX encourages you to participate in an electronics recycling program.
WARRANTY CONDITIONS
- For any defect, in the judgment of our technician, caused under normal use, we are responsible for repairing free of charge 12 months commencing from the date of purchase at the discretion of our company;
- A valid warranty card and original purchase invoice must be presented upon request of warranty service;
- This warranty card shall not apply to the product if:
- (a) it has explicitly modified or repaired in any way by persons other than technicians of this company, or;
- (b) it has been damaged through misuse, malicious acts, negligence, the inflow of any liquid, or;
- (c) losses or damages are caused by force majeure or natural disasters.
- No alteration to this warranty card will be allowed;
- The warranty terms and conditions are subject to change without prior notice;
- Please retain your proof of purchase for warranty service;
- Please consult the dealer about the product compatibility with your cell phone/PDA before purchase. Product specifications are subject to change without prior notice;
- Please visit www.momax.net for the latest product information.
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a class
B digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used under the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. if this
equipmemt does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Customer Service
-
Hong Kong and Macau:
Unit A, 4/F., Cheung Lung Ind. Budg., Lai Chi Kok, Kowloon, Hong Kong10 Cheung Yee Street, -
Hotline: 852-2402 3186
-
E-Mail: info@momax.net.
Copyright© 2024 MOMAX Technology Ltd. All rights reserved. MOMAX is a registered trademark of MOMAX Technology Ltd. All other trademarks are the property of their respective owners. www.momax.net.