tp-link Archer NX200 5G CPE Router Installation Guide

tp-link Archer NX200 5G CPE Router

Specifications

• Model: 5G Router
• Wireless Standard: 802.11ac/n/a 5GHz, 802.11b/g/n 2.4GHz
• Ports: LAN/WAN port, USB port
• Security: WPA/WPA2 encryption, SPI firewall
• Supported Modes: Router, EWAN Mode
• Manufacturer: TP-Link

Product Usage Instructions

Customizing the 5G Router

1. Ensure your computer is connected to the router either wired or wirelessly.
2. Open a web browser and enter either http://tplinkmodem.net or http://192.168.1.1  Create a new password for future logins.
3. Follow the Quick Setup instructions to complete the initial configuration.

EWAN Mode: To configure the router for Cable connections or more advanced settings, refer to the user guide on the TP-Link official website.

Need Help?

FAQ:

1. Q1. What should I do if I cannot access the web management page?
   If the login page does not appear, refer to Q1 in the guide for troubleshooting steps.

2. Q2. What should I do if I cannot access the internet?
   Follow these steps:

   • Verify ISP parameters in Mobile WAN settings.
   • Check PIN Management for correct PIN entry.
   • Adjust Data Settings if necessary.
   • Ensure Mobile Data is enabled.
   • Enable Data Roaming if in a roaming area.
   • Select the correct Antenna Type.

3. Q3. How do I restore the router to its factory default settings?
   Refer to the user guide for instructions on resetting to factory  defaults.

4. Q4. What should I do if I forget my web management page password?
   Go to Basic > Wireless in the web management page to retrieve or reset your wireless password.

5. Q6. What should I do if I want to change the LAN/WAN port configuration?
   Refer to the user guide for instructions on changing port configurations.

For technical support and other resources, visit TP-Link’s official support page or scan the QR code provided.

Connect the Hardware

*Images may differ from actual products.

Note: The RESET button is actually a shared RESET/Wi-Fi button (short press for 5 seconds or less is for Wi-Fi function, long press for 5 seconds or more is for RESET function). A short press will cause the Wi-Fi in use to turn off.

Verify the Hardware Connection

Check the following LEDs’ status. If the Internet LED is on, your router is connected to the internet successfully.
Note: If the Internet LED does not turn on, please refer to Q2 of Need Help? in this guide.

Enjoy the Internet

• Wired
  Connect your computers to the router’s LAN ports via Ethernet cables.
  Note: The LAN/WAN port defaults to WAN port. Please refer to Q6 of Need Help? in this guide if you want to change it to LAN port.

• Wireless
  Find the SSID (network name) and wireless password printed on the label at the bottom of the router.

• Click thenetwork icon of your computer or go to Wi-Fi settings of your smart device, and then select the SSID to join the network.

Configure the router via Tether App

The TP-Link Tether app provides a simple, intuitive way to access and manage your router.

• Block unwelcome users from connecting to your network
• View information about clients connected to your router
• Change the basic wireless network settings
• Set up Parental Controls with access time

How to begin?

1. Download the TP-Link Tether app.

Open the Tether app and log in with your TP-Link ID.
Note: If you don’t have an account, create one first.
Tap the + icon in the Tether app and select 5G/4G Router. Follow the steps to complete the setup and connect to the internet.

Customize the 5G Router

1. Make sure your computer is connected to the router (wired or wireless).

2.  Launch a web browser and type in http://tplinkmodem.net or http://192.168.1.1. Create a new password for future logins.
   Note: If the login page does not appear, please refer to Q1 of Need Help? in this guide.

3. Follow the step-by-step instructions of the Quick Setup to complete the initial configuration.
   Note: The router can also be used (or configured) in EWAN Mode(wireless router mode) for Cable connections. For more advanced configurations, please refer to the user guide on TP-Link official website at www.tp-link.com

Need Help?

1. Q1. What should I do if I cannot access the web management page?
   • If the computer is set to a static IP address, change its settings to obtain an IP address automatically.
   • Make sure http://tplinkmodem.net or http://192.168.1.1 is correctly entered in the web browser.
   • Use another web browser and try again.
   • Reboot your router and try again.
   • Disable and enable the active network adapter in use.
2. Q2. What should I do if I cannot access the internet?
3. Verify that your SIM card is a 5G/4G or WCDMA card.

  * Verify that your SIM card is in your internet service provider’s service area.
  * Verify that your SIM card has sufficient credit.
  * Check the LAN connection: Open a web browser and enter <http://tplinkmodem.net> or http://192.168.1.1 in the address bar. If the login page does not appear, refer to Q1 and then try again.
  * Launch a web browser, log in to the web management page, and check the following:
2. Go to Advanced > Network > Mobile WAN to verify the parameters provided by your ISP are correctly entered. If the parameters are incorrect, click Create Profile and enter the correct parameters, then select the new profile from the Profile Name list.
3. Go to Advanced > Network > PIN Management to verify if PIN is required. If it is, enter the correct PIN provided by your ISP, and click Save.
4. Go to Advanced > Network > Data Settings to verify if the Total/Monthly Used exceeds the  

Total/Monthly Allowance. If it does, click Correct and set Total/Monthly Used to 0 (zero), or disable
Data Limit.

5. Go to Advanced > Network > Mobile WAN to verify that Mobile Data is enabled. If it is not, enable it to access the internet.
6. Confirm with your ISP if you are in a roaming service area. If you are, go to Advanced > Network > Mobile WAN to enable Data Roaming.
7. Confirm the selection of Antenna Type.  

If it is determined that an external antenna is connected, select External 5G/LTE Antennas.
If you are sure that no external antenna is connected, select Internal 5G/LTE Antennas.

3. Q3. How do I restore the router to its factory default settings?

   • With the router powered on, press and hold the RESET button on the rear panel of the router until the Power LED starts flashing, then release the button. Wait while the router resets.
   • Log in to the web management page of the router, and go to Advanced > System Tools > Backup &
     Restore, click Factory Restore and wait until the reset process is complete.

4. Q4. What should I do if I forget my web management page password?

   • If you are using a TP-Link ID to log in, click Forgot password on the login page and then follow the instructions to reset it.
   • Alternatively, refer to Q3 to reset the router, then create a new password to log in.

5.  What should I do if I forget my wireless network password?

   • The default wireless password is printed on the product label of the router.
   • Connect a computer directly to the router using an Ethernet cable. Log in to the router’s web management page and go to Basic > Wireless to retrieve or reset your wireless password.

6. What should I do if I want to change the LAN/WAN port from default WAN port to LAN port?

   • Log in to the web management page of the router, and go to Advanced > Network > Internet to verify the default gateway. If it is in Auto mode, delete the profile from the Internet Setup list and click Save. Then the default WAN port will change to LAN port.

For technical support, replacement services, user guides, and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at https://www.tp- link.com/en/support/ce/

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at https://www.tp- link.com/support/ukca/

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.
  ©2024 TP-Link 7106510959 REV2.0.0

References

• Trying to configure the Modem? | TP-Link
• WiFi Networking Equipment for Home & Business | TP-Link
• CE Regulatory Compliance | TP-Link
• TP-Link Product Support - Wireless Networking Equipment Support
• Regulatory Compliance | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>