Ricoh OTY0GV1 Connecting a Audio Device and the Remote Controller Owner’s Manual

Ricoh OTY0GV1 Connecting an Audio Device and the Remote Controller

Specifications

• Power Supply: AC 100-240V, 50/60Hz
• Audio Output: 3.5mm
• Power Cord: Standard AC cord

Connecting an Audio Device and the Remote Controller

Note
If speakers without built-in amplifiers are used, prepare a separate amplifier. When external speakers are connected, no sound is output from the main unit’s speakers. The volume of the external speaker can be adjusted with the [Volume +/-] button.

Connecting a USB Device

Insert the USB memory device into the designated port on the projector.

Using the Power Cord Stopper

Note: To prevent the power cord from accidentally disconnecting, use the power cord stopper.

Installation

1. Align the power cord stopper with the hole below the AC IN terminal and push it in.
2. Pass the power supply cord through the clamper and press to fix it.

Removal

1. Pull to an appropriate position while pushing down the knob of the power cord stopper.
2. Press down the knob on the clamper to open it and remove the power cord.

Powering On

1. Ensure the power cord and stopper are securely connected.
2. Turn on the projector using the button on the control panel or remote control.
3. The Power indicator will turn red initially and then blue once powered on.

Frequently Asked Questions

Q: How do I adjust the volume when using external speakers?
A: You can adjust the volume of external speakers connected to the projector using the [Volume +/-] button on the remote controller.

Q: What should I do if the Power indicator does not turn on?
A: Make sure that the power cord and stopper are properly connected and that the power plug is fully inserted into both the projector AC inlet and the wall outlet. Ensure that the AC outlet is near the equipment and easily accessible.

Basic Operations
Connecting a Audio Device (Audio) and the Remote Controller

Note
If speakers without built-in amplifiers are used, prepare a separate amplifier.
When external speakers are connected, no sound is output from the main unit’s speakers.
The volume of the external speaker can be adjusted with the [Volume +/-] button.

Audio cable (3.5)

Audio cable (3.5)

44
English

Basic Operations
Connecting a USB Device
USB memory device
45
English English

Basic Operations

Using the power cord stopper
To prevent the power cord from accidently removing from the AC IN of the projector, use the power cord stopper.

Note
If you pull on the power supply cord while the connector is fixed, the main unit may fall down and be damaged.

CAUTION: To prevent the power cord from coming loose, make sure that all the prongs of the power cord are fully inserted into the AC IN terminal of the projector before using the power cord stopper to fix the power cord. A loose contact of the power cord may cause a fire or electric shock
Installing the power cord stopper
1. With the clamper facing the power supply cord, align the tip of the power supply cord stopper with the hole below the AC IN terminal and push it in.

2. Pass the power supply cord through the clamper and press the clamper to fix it.

3. Pass the power supply cord through the clamper and press the clamper to fix it.

46
English

Clamper

Basic Operations

Disconnecting the power cord stopper
1. Pull to an appropriate position while pushing down the knob of the power cord stopper.
2. Press down the knob on the clamper to open the clamper and take out the power cord.
3. Push and pull the fitted part of the power cord stopper from the left and right to remove it from the main unit.

Clamper

Knob

Knob

47
English English

Basic Operations

Powering On/Off the Projector

Powering on the Projector

Note

1. Please make sure the power cord and power cord stopper

Make sure that

are securely connected. The Power indicator will turn red.

the power plug is

fully inserted into

both the projector

AC inlet and the

wall outlet.

The AC outlet must be near this equipment and must be easily accessible.

Note
If you connect multiple sources at the same time, press “Input” to switch inputs.

Connect the power cord and stopper to the projector.
2. Turn on the projector by pressing the ” ” button on the top control panel or on the remote control.
or

Note
Turn on the projector first and then the signal sources.

The Power indicator will flash blue.
The startup screen will display and the Power indicator will turn blue.
3. The first time you use the projector, you will be asked to select the preferred language. Turn on your source (computer, notebook, video player, etc.) The projector will detect your source automatically.
Make sure that the [Auto Source] has been set to [On].

• [Auto Source] is set to [On] as a factory default value.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>