102895 Cape Floor Light

Product Information

Specifications:

• Type: Floor Light

• Manufacturer: UK Manufacturer: BH17 7BY, EU Manufacturer:
  Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

• Plug Type: 3 pin UK plug (can be converted to 2 pin Europe
  plug)

• Model Number: 102369_102895_01252024

Product Usage Instructions:

Installation and Safety Instructions:

Ensure the product is installed following the assembly
instructions provided. Make sure to check and replace any faulty
bulbs with caution.

Safety Warnings:

Do not dispose of the product with household waste. Recycle
where facilities exist. Consult your Local Authority or local store
for recycling advice.

Care and Maintenance:

When replacing the bulb, switch off the product and allow it to
cool down as the bulb may get hot during use. Clean the product
with a dry cloth only, avoiding liquid or abrasive cleaners.

Troubleshooting:

If the bulb does not light after installation, follow these
steps:

1. Plug in and operate the foot switch to turn the lamp on.

2. Check the bulb for any issues.

3. Inspect the 3 amp fuse in the plug and relevant fuse in your
   fuse box.

4. If unsure, consult a qualified electrician for assistance.

Converting 3 Pin to 2 Pin Plug:

1. Loosen the central screw to remove the 3 pin adaptor.
2. Remove the adaptor to reveal the 2 pin Europe plug.

Assembly Instructions:

To adjust and assemble the floor light:

1. Pull any excess cable through from under the base and out
   through the side of the base.

2. Adjust and retighten the nut to ensure the cable is at the back
   of the product when assembled.

Contact Information:

For any further inquiries or assistance, please contact the
manufacturers at the provided addresses.

FAQ:

Q: How do I replace the bulb in the floor
light?
A: To replace the bulb, switch off the product, allow it to cool
down, then carefully replace the bulb following the manufacturer’s
instructions.

Installation and Safety Instructions
Floor Light

Safety Warnings
These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician. This product is only suitable for connection to a 220-240V~ 50Hz supply. It is for indoor use only, and not suitable for a bathroom location. This fitting is a Class II, Double Insulated product and does not require an Earth. Live or Neutral must not be connected to Earth. Do not attempt to plug in or use this product until it has been fully assembled. Disconnect from mains during assembly or maintenance. this product must be used on a stable, flat surface. Under no circumstances must this floor lamp be covered with any material as this could pose a safety hazard. This product is not suitable for persons under 14 years of age. This product may contain delicate parts ­ be careful during handling and maintenance to avoid breakage. The lamp must be protected by a 3 amp fuse in the mains plug. Never fit bulbs of a higher wattage than those specified on the label as these may damage the fitting. The lampshade part can be adjusted to an appropriate angle as needed.` Never put anything on the product or hang anything on any part of this product. If the external flexible cable or cord of this luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product and allow it to cool down (Caution: bulb gets hot during use). Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.

Troubleshooting
When the bulb does not light after installation: > Please plug in and operate the foot switch to turn your lamp on. > Please check the bulb. > Please check the 3 amp fuse in the plug and ultimately check the relevant fuse in your fuse box. If you have any doubt about installation/use of this product, consult a qualified electrician.

To use this item in Europe, the 3 pin adaptor can be removed by loosening the central screw and removing the adaptor to reveal the 2 pin Europe plug.

Converting 3 pin to 2 pin plug

1

2

3

BS 5733

BS 5733

BS 5733

102369_102895_01252024

UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Assembly Instructions
Adjustable
1

On / off switch
7

2

Gently pull any excess cable through from under the base and then out through the side of the base. Nut can be adjusted and retightened to ensure the cable is at back of product when assembled.

6

3

4

5

UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>