Saxby Lighting 108867 RularPRO MW Instruction Manual

: August 9, 2024
: saxby lighting

Saxby Lighting 108867 RularPRO MW

Saxby-Lighting-108867-RularPRO-MW-Product

Product Information

Specifications

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type:
- 108867: 31.5W/20W LED (SMD) CCT, 3000/4000/6000K
- 108868: 39W/26W LED (SMD) CCT, 3000/4000/6000K
- 108869: 44W/35W LED(SMD) CCT, 3000/4000/6000K
Energy efficiency class C
Non-replaceable light source
Replaceable control gear by a professional
Class 1 products, must be connected to the earth
Not suitable for dimming
For indoor use only

Product Usage Instructions

Installation

Remove existing fittings completely before installing the new product. Note the position of wires from the existing fitting.
Ensure the switch is turned off before installation.
Mount the product on a flat and smooth surface for a secure fit.

Wattage Adjustment

Use the wattage switch on the driver to adjust the wattage.
For 108867, select between 20W and 31.5W.
For 108868, select between 26W and 39W.
For 108869, select between 35W and 44W.

Color Temperature Adjustment

Use the CCT switch on the driver to adjust the color temperature between 3000K, 4000K, and 6000K.
Choose your preferred wattage and color temperature before installation using the switches on the driver.
Turn off the power switch before changing wattage or color temperature for safety.

Wiring
This product is Class I and must be earthed. Connect the wiring from the existing light fitting to the connection block inside the product as per the wiring diagram provided in the manual.

FAQs

Q: Is the light source replaceable?
A: No, the light source is non-replaceable. The control gear can be replaced by a professional.
Q: How many color temperature options are available?
A: The product offers color temperature options of 3000K, 4000K, and 6000K.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Safety Warning

This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install by the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk of being cut, trapped, or damaged.
The main supply cable must have a minimum cross-section area of 1.0mm2.
Cables must be protected using suitable conduit or plastic trunking.
Take care not to drill into any pipes or main cables beneath the surface during mounting hole preparation.
This product can be installed on the ceiling or wall.

Technical Data

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type:
- 108867: 31.5W / 20W LED (SMD) CCT, 3000/4000 /6000K
- 108868: 39W / 26W LED (SMD) CCT, 3000/4000 /6000K
- 108869: 44W / 35W LED(SMD) CCT, 3000/4000 /6000K
- This product contains a light source of energy efficiency class C.
Non-replaceable light source
Replaceable control gear by a professional
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1 and must be connected to Earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
This product is for indoor use only.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

Note that the switch is turned off before installation.
The mounting surface must be flat and smooth to ensure a good fit.
The wattage is changeable by using the wattage switch on the driver.
- For the 108867 is the 31.5W/20W selectable
- For the 108868 is the 39W/26W selectable
- For the 108869 is the 44W/35W selectable
The color is changeable between 3000/4000/6000K using the CCT switch on the driver before installation.
Choose your preferred wattage and color before installing by wattage switch or CCT switch on the driver.

Note:
Before you change the wattage or color, please turn off the power switch for safety.

$Saxby-Lighting-108867-RularPRO-MW-Fig- $12$$

Hold the product in place and mark the position of the fixing holes. This may require the help of an assistant. If wall mounting, ensure that the product is level.
Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for bricks, cavity walls, or plasterboard.
Ensure the ceiling or wall is capable of holding the weight of the product and then fix brackets in place.
Rotate both ends of the product in the direction of the arrow to open the diffuser cover.
Pull the supply cable through the middle grommet and fix the light fitting into position using appropriate fixings.
Connect the supply cable to the quick-fit terminal block as detailed wiring diagram.
Close the diffuser cover into place.
Replace the fuse or circuit breaker and switch it on. Your light is now ready for use.

$Saxby-Lighting-108867-RularPRO-MW-Fig- $13$$

Wiring

This product is a Class I product and must be earthed.
Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in the following way:
Under the master-slave mode, when maintaining the slave lamps, turn off the supply of both ends of the Master to avoid the risk of electric shock. $Saxby-Lighting-108867-RularPRO-MW-Fig- $14$$

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

DETACHED SENSOR ON/OFF FUNCTION

220-240VAC Input, ON/OFF Function
Special Detached Design For More Applications
DIP Switch Control, User Friendly
5 Years Warranty

Mechanical structure

Installation Hole
Input
Output
Daylight Sensor
Microwave Module
Daylight Threshold
Hold Time
Detection Area

Dimensions

Unit: mm

$Saxby-Lighting-108867-RularPRO-MW-Fig- $18$$

Wiring Diagram

Shown-part length is about 335mm

$Saxby-Lighting-108867-RularPRO-MW-Fig- $19$$

Sensor Technical Data

Operating Voltage 220-240VAC 50/60Hz
Stand-by Power ≤0.5W
Microwave Frequency 5.8GHz±75MHz
Microwave power <0.3mW
Connection L.N.N.L’
Detection Angle 30-150° Without Glass Cover
Detection Area 10%/50%/75%/100%
Hold Time 5s/90s/5min/15min
Mounting Height Max. 4m/13.12ft Ceiling Mounted
Detection Range Max. ø14m/45.92ft Ceiling Mounted
Daylight Threshold 2Lux/10Lux/50Lux/Disable
Switching capacity Max. 400W Control Gear; Max. 800W Incandescent lamp
Programming DIP
Control ON/OFF
Operating Temperature 25°C~+60°C
Motion Detection 0.5~1.5m/s
IP Rating IP20
Warranty 5 years

Dial code setting

$Saxby-Lighting-108867-RularPRO-MW-Fig- $20$$

Detection Patterns

The highest mounting height is 4m
This figure indicates the maximum distance at the highest mounting height with 100% sensitivity. $Saxby-Lighting-108867-RularPRO-MW-Fig- $21$$

Performance

Daylight Disable
When the daylight threshold is preset as “disable”, the sensor turns the light ON when motion gets detected, and OFF after hold.

$Saxby-Lighting-108867-RularPRO-MW-Fig- $22$$

Installation precautions

Microwave sensors can be installed in any lamp except the one with a full metal shell.
The detected surface cannot be shielded by metal objects.
Make sure the microwave module is completely exposed outside.
The detection surface of the sensor module shall be installed facing the detection area.
Should be kept away from the driver to avoid interference generation and lamp flashing.
Wiring must be strictly by the wiring diagram to avoid short circuits.

User Notes

Microwave can penetrate walls or glass thinner than ＜20mm and attenuate if thicker than ＜20mm.
The driver voltage shall be stable and float within 10%.
The detection area will be affected by the speed of motion, mounting height, and movement volume.
Conduct a test on sunny days without the lampshade which will affect the tested lux value.
3M distance is suggested when having a lot of sensors in the same room.
If the sensor is applied in the room with a 5G WiFi router, a 3M distance or above is needed.

Application Environment

Suitable for indoor installation to avoid false triggering due to external factors such as rain, wind, or tree swing.
Shall not be installed in the place with all four metal shelters and small space (such as galvanized-iron roof).
Shall not be mounted installation, to avoid false triggers caused by the lamp itself shaking.
Shall not be installed next to large operating machines such as ventilator/ceiling fan to avoid false triggering caused by machine vibration.
The sensor might be unwanted triggered in rooms that are small, or mostly filled with metal materials; please try to decrease sensitivity when it happens or contact us for support.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting- info.co.uk/108867.

V4 24/01/2024