FREEWING F-105 Thunderchief 64mm EDF PNP Jet User Manual

FREEWING F-105 Thunderchief 64mm EDF PNP Jet

Product Information

Product Specifications

• Wing Loading: 70g/dm2
• Wing Area: 7dm2
• Motor: 2627-4500KV Brushless Outrunner Motor
• Ducted fan: 64mm 5-Blade Fan
• ESC: 30A Brushless
• Servo: 9g Plastic Servo (2pcs)
• Top Speed: 120KPH/75MPH
• Empty Weight: 360g (without battery)
• Bench Tested Thrust: 750g
• Landing gear: fixed landing gear (Optional spare part, need to purchase separately)

FAQ

• Q: What type of battery does the F-105 Thunderchief use?
  • A: The F-105 Thunderchief uses a battery with dimensions of L=150mm, W=42mm, H=42.5mm. Before connecting the battery and receiver, ensure that the transmitter power is switched on and the throttle stick is in the lowest position.

Introduction

Note

1. This is not a toy! Operater should have a certain experience, beginners should operate under the guidance of professional players.
2. Before install, please read through the instructions carefully and operate strictly under instructions.
3. Cause of wrong operation, Freewing and its vendors will not be held responsible for any losses.
4. Model planes’ players must be on the age of 14 years old.
5. This plane used the EPO material with surface spray paint, don’t use chemical to clean, otherwise it will damage.
6. You should be careful to avoid flying in areas such as public places,high-voltage-intensive areas,near the highway, near the airport or any other place where laws and regulation clearly prohibit.
7. You cannot fly in bad weather conditions such as thunderstorms,snows….
8. Model plane’s battery, don’t allowed to put in everywhere. Storage must ensure that there is no inflammable and explosive materials in the round of 2M range.
9. Damaged or scrap battery should be properly recycled, it can’t discard to avoid spontaneous combustion and fire.
10. In flying field, the waste after flying should be properly handled, it can’t be abandoned or burned.
11. In any case, you must ensure that the throttle is in the low position and transmitter switch on, then it can connect the lipo-battery in aircraft.
12. Do not try to take planes by hand when flying or slow landing process. You must wait for landing stop, then carry it.

Product Overview

Standard version

• Wing Loading： 70g/dm
• 2 Wing Area： 7dm
• Motor： 2627-4500KV
  • Brushless Outrunner Motor
• Ducted fan: 64mm 5-Blade Fan
• ESC: 30A Brushless
• Servo: 9g Plastic Servo (2pcs)
• Top Speed:  120KPH/75MPH
• Empty Weight: 360g(without battery)
• Bench Tested Thrust: 750g
• Landing gear: fixed landing gear
  • (Optional spare part, need to purchase separately.)

Note: The parameters in here are derived from test result using our accessories.
If use other accessories, the test result will be different. Any problem since of using other accessories, we are not able to provide technical support.

The package don’t include the landing gear, if you need, please contact your local dealer.

Contents

Different equipment include different spareparts. Please refer to the following contents to check your sparepart list.

PNP Installation Instructions

As shown in this photo:

1. Insert the carbon tube into the fuselage and keep it in the center.
2. Apply the glue on the main wing install position of fuselage (Indicated position as the photo shown), then install the main wing on the fuselage and wait for it solidify.

Install Horizontal Stabilizer

1. Use glue to attach the horizontal tail on the fuselage as the below photo shown.

Install Vertical Stabilizer

• Use glue to install the vertical stabilizer on the rear fuselage. Ensure it is 90 degrees to the horizontal plane of the fuselage. A crooked vertical stabilizer will hinder flight.

Install Elevator pushrod

1. Use a servo tester or radio to center each servo.
2. Insert the threaded side of the rod to the plastic tube and tighten the clevis.
3. One side pushrod insert to the servo arm,adjust its length.And insert the clevis to the elevator pushrod horn.
4. Repeat these 3 steps for the other side.

Install Aileron pushrod

1. Use a servo tester or radio to center each servo.
2. One side pushrod insert to the servo arm,adjust its length.And insert the clevis to the aileron pushrod horn.
3. Repeat these 2 steps for the other side.

Pushrod Instructions

Aileron pushrod size

Elevator pushrod size

Aileron pushrod mounting hole

Elevator pushrod mounting hole

Battery Size

Center of Gravity

Correct Center of Gravity (”CG”) is critical for the aircraft to fly safely and in control.
Please refer to the following CG diagram to adjust your plane’s Center of Gravity.

• You can move the battery forward or backward to adjust the Center of Gravity.
• If you cannot obtain the recommended CG by moving the battery to a suitable location, you can also install a counterweight to achieve correct CG. However, with the recommended battery size,no counterweight is required. We recommend not flying with a battery size that requires a counterweight.

Control Direction Test

After installed the plane, before flying, we need a fully charged battery and connect to the ESC, then use radio to test and check that every control surface work properly.

Aileron

Elevator

Dual Rates

• According to our testing experience, use the following parameters to set Aileron/Elevator Rate.
• Program your preferred Exponential % in your radio transmitter. We recommend using High Rate for the first flight, and switching to Low Rate if you desire a lower sensitivity. On successive flights, adjust the Rates and Expo to suit your preference.

 | Aileron ( measured closest to the fuselage)| Elevator(measured closest to the fuselage)
---|---|---
Low Rate| H1/H2 7mm/7mm D/R Rate：75%| H1/H2 13mm/13mm D/R Rate：75%
High Rate| H1/H2 9mm/9mm D/R Rate：100%| H1/H2 15mm/15mm D/R Rate：100%

Accessories Description

Motor Specifications

Power system No.| EDF Fans| Use voltage (V)| Current(A)| Max power (W)| Thrust(g)| Efficiency (g/w)| Motor Specifications

（KV）

| Rotating speed

(rpm)

| Weight

( g )

---|---|---|---|---|---|---|---|---|---
E7201| 64mm 5-blade EDF| 11.1(3S)| 28| 310| 750| 2.4| 2627-4500| 49000| 50

Motor Overview

Standard version

• A – Motor 2627-4500KV
• B- 64mm Outrunner ducted frame
• C- Screw (PM2.5×6 2pcs)
• D- Motor collet
• E- Motor collet backplate
• F- 64mm 5-blade ducted fan
• G- Nut

As the left diagram, install ESC and power system

• A- ESC fixed wood piece
• B- ESC
• C- 64mm EDF power system
• D- Fin
• E- EDF cover
• F- Screw (KA2.3×8)
• G- Fuselage cover

Note

When the ESC and battery are connected, avoid touching the ESC by hand to avoid accidental injury due to heat When testing the EDF, please use safety test stand for testing.Never hold an EDF unit in your hand while it is powered on.

Servos Introductions

The servo positive or reverse rotation is defined as follows:

• When servo input signal change from 1000µs to 2000µs,
• The servo arm is rotated clockwise, its positive servo.
• The servo arm is rotated counterclockwise, its reverse servo.

If you need to purchase another brand’s servo, please refer to the following list to choose a suitable servo

Position| Servo regulation| No.| Pos./Rev.| Cable length
---|---|---|---|---
Main wing(L)| 9g plastic servo| 1| Positive| 300mm
Main wing(R)| 9g plastic servo| 2| Positive| 300mm

Landing Gear Assemble

Landing gear is the optional part,please consult with the local distributor to purchase, and refer to the following instructions to install.

Install nose landing gear

Please refer to the following photo for assembly and installation of the landing gear.

• A – Servo fixed mount
• B – 9g Servo
• C- Screw (PWA2.3×8 1pcs)
• D- Set screw (M3x3 4pcs)
• E- Nose wheel strut fixed piece
• F – Nose wheel strut (top)
• G- Wheel connecting part
• H- Nose wheel strut (bottom)
• I – Nose wheel (035x10mm)
• J – Wheel chock
• K- Nose landing gear

Install rear landing gear

Please refer to the following photo for assembly and installation of the landing gear.

Spare part name and parameters

• A. Set screw (M3x3)
• B. Wheel chock
• C. Nose wheel (Ø50x15mm)
• D. Rear gear main strut
• E. Main landing gear fixed mount
• F. Main landing gear door

Contact

Dongguan Freewing Electronic Technology Ltd
HK Freewing Model International Limited

• Add.: FeiYi Building,face to Labor Bureau, Fumin Middle Road, Dalang Town, Dongguan City, Guangdong Province, China
• Web: http://www.sz-freewing.com
• Email:freewing@sz-freewing.com
• Tel: 86-769-82669669
• Fax: 86-769-82033233
• www.sz-freewing.com

Scan

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>