SIZZLE WJ-1200R Speaker Tower User Manual
- June 15, 2024
- SIZZLE
Table of Contents
User Manual
WJ-1200R Speaker Tower Please read carefully this manual before operating
the device. Keep it for future reference.
Dear Customer:
Thank you for purchasing our pairing Tower Speaker WJ1200R before using this
device, please read the user manual carefully in order to operate it normally.
Safety instructions
Read this User Manual before you attempt to connect or operate the device.
Save this User Manual for future reference. The device should not be exposed
to dripping or splashing and no objects filled with liquids should be placed
on the product. Use the device in a dry location only. No naked flame source,
such as candles, should be placed on the product. Only use the original
accessories or the ones specified by the manufacturer. Install the unit in
accordance with the manufacturer’s instructions.
Place the unit where there is good ventilation.
Place the device on a flat, hard and stable surface. Do not expose it to
temperatures above 40°C. Allow at least 10 cm clearance from the rear and the
top of the unit and 5 cm from each side. Press the player’s buttons gently.
Pressing them too hard can damage the device.
Dispose of the used batteries in an environmental-responsible manner. Rlways
ensure that the product is unplugged from the electrical outlet before moving
or cleaning it. Clean it with dry cloth only.
Turn off the product during lightning, storms or when it will not be used for
long periods of time.
This product has no user-serviceable parts.
Do not attempt to repair this product yourself. Only qualified service
personnel should perform servicing.
Do not place the unit near TVs, speakers and other objects that generate
strong magnetic fields.
Do not leave the unit unattended when it is in use.
Setup
- Take out the speaker body and speaker base carefully from the box.
- Take out the accessories.
- Fit the base with the body aligning the holes on the base with the holes on the tower.
- Screw the base into the body.
- Place the speaker standing on the floor and it’s ready to use.
Top Panel
- VOLUME – / VOLUME +
- PLAY / PAUSE
- MUTE
- PREV
- FOLDER
- STANDBY/MODE
- NEXT
- MemCd
- USB SLOT
- USB SLOT FOR CHARGE
- AUXRCA input
- AUX 3.5mm Jack input
- Charging indicator
- DCinput
Remote control
- STANDBY /ON
- PLAY / PAUSE button
- FOLDER
- SEARCH
- NUMBER buttons
- MUTE
- EQ
- REPEAT
- STOP
- PREVIOUS / CH –
- NEXT/CH+
- TUNING +
- TUNING –
- VOLUME –
- VOLUME +
- MODE
Using the Remote Control to Operate the Unit
Aim the remote control directly at the remote control sensor (IR) on the front
panel. Don’t put any objects between the remote control and the system while
operating the unit.
To get your remote control working initially, pull the clear tab from the
battery compartment located at the bottom of the remote.
Using the AUX input
There are two Aux-in connections located on the unit. Analogue sound signals
from other sources can be input to the speaker through these connections.
Press the “MODE” button on the tower speaker or press the “MODE” button on the
remote control to switch to the desired AUX IN connection.
AUX-IN
- Connect the Aux In cable to the Aux-in jack. Connect the other end of the cable to an MP3 player or other audio source.
- Long press “ /MODE” button to turn the speaker on.
- Press the “MODE” button to switch to Aux-in mode.
- Use the controls on the connected device to begin playing music.
Wireless pairing function
- Long press” /MODE “button, to turn on the speaker, press “ /Mobe “ button on the remote control to swith to the pairing mode.
- Activate the pairing function of your mobile phone (or other device you want to connect). Your device must search and find the device name “WJ-1200R”.
- Select “WJ-1200R” and the speaker will automatically connect with your phone (some mobile phones need you to input the PIN code that appears on the mobile phone screen).
- If the Smart Phone/tablet cannot find the unit or can’t pair, please power off and after power on and repeat the above steps.
- The tower speaker will automatically reconnect with the last connected device (mobile phone or other device).
- If you manually turn off the pairing function of the Smart Phone or the Smart Phone far away from the unit (over 10m), the connection between the speaker and the Smart Phone will be lost and the unit will enter the pairing standby mode.
USB port for playing MP3
Power on the unit and insert a USB Flash Drive (not supplied) into the USB
Port, ensuring the plug is fully and correctly inserted.
The tower speaker will play music from the USB automatically or press “MODE”
button on the remote.
USB port for charging
The USB power output DC 5V 1A supports charging of many electronic devices.
When charging devices, make sure that the power supply is proper for your
device.
MemCd slot for playing MP3
Insert an MemCd (not supplied) into the MemCd expansion slot. Make sure it is
inserted correctly. The tower speaker will play music from the MemCd
automatically or press “MODE” button on the remote.
FM Radio operation— Turn on the speaker and make sure that it’s in FM
mode. Press SEARCH button on the remote control to search and store radio
channels automatically. The tower speaker can store SO radio channels.
RAfter the search is finished, the unit will play the first channel. Press
NEXT or PREVIOUS buttons on the remote control to select the next or the
previous radio channel. If the channel signal is not good, it can be fine
tuned by pressing the TUN- or TUN+ buttons to adjust the signal.
For a better sound quality, please make sure that the FM Antenna has been
fully extended.
Care and Maintenance
Disconnect the device from the power source when cleaning it. If needed, wipe
it with a soft and dry cloth. Do not use any wax, polish sprays, or abrasive
product to clean the device.
FAQ / Troubleshooting
| Question / Problem | Solution |
|---|---|
| The speaker cannot pair with the mobile phone | Make sure that the speaker is |
in pairing mode/ Check if the pairing search function of your
mobile phone has been turned ON/Check your mobile device’ s pairing menu and
delete/forget
the speaker and reconnect the speaker again following the user manual
Speaker cannot be switch on| Please check the speaker’s power cable and make
sure that is correctly connected to a power outlet.
Remote control is not working correctly| If the remote control is not working
or you need to move closer to the speaker to operate it, then probably the
remote control battery needs to be replaced.
No sound in RUX IN mode| Pull out both ends of the audio cable and plug in
again / replace the audio cable
Speaker disconnect with your mobile phone within 10 meter| Please check if
there are walls, metal or other
materials that may interfere with the wireless connection (Wireless pairing is
a radio technology that is sensitive to objects between the speaker and the
| connected device).
Cannot hear sound from your mobile phone| Check the volume of the tower
speaker and of your mobile phone.
Cannot use the speaker to control volume or select track of RPP of your mobile
phone| Software settings of RPP may be varied and some functions of the RPP
may not control by the speaker.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. such modifications
could void the user’s authority to operate the equipment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.