ESTES 9722 So Long Rocket Kit Installation Guide

ESTES 9722 So Long Rocket Kit

Product Specifications

• Model: 9722
• Brand: EstesRockets.com
• Recommended Age: 18+
• Skill Level: Advanced

Product Usage Instructions

Supplies Needed

• Scissors
• Pencil
• Ruler
• Fine Sandpaper
• Epoxy
• Yellow Glue
• Clear Tape
• Hobby Knife
• Masking Tape
• White Primer
• Clear Coat
• White & Black Sanding Tape
• (Optional) Paint

Assembly Instructions

TUBE MARKING GUIDE AND SHOCK CORD MOUNT
Use masking tape to mark the booster body tube and create guide lines. Extend lines using a door frame.

PREPARE BOOSTER FINS

1. Sand both sides of the balsa sheet.
2. Carefully remove all C pieces with a hobby knife.

ATTACH BOOSTER FINS

1. Round the leading edges of all C pieces.
2. Reference the fin alignment template for proper placement.

Frequently Asked Questions (FAQ):

1. Q: How important is proper fin alignment for the rocket’s flight?
   A: Proper fin alignment is crucial for a stable and safe flight. Use the included template to ensure correct placement during assembly.

2. Q: What should I do if I encounter missing parts during assembly?
   A: Please contact customer support at EstesRockets.com for assistance in obtaining any missing parts needed for assembly.

MODEL ROCKET INSTRUCTIONS

KEEP FOR FUTURE REFERENCE
IMPORTANT: Please record date found on decal and keep for future reference.

READ ALL INSTRUCTIONS. Make sure you have all parts and supplies. Test fit all parts before applying glue. Refer to your glue manufacturer’s dry times during build.

SUPPLIES

TUBE MARKING GUIDE AND SHOCK CORD MOUNT
Make a copy if you want to keep instructions.

MARK BOOSTER BODY TUBE

PREPARE BOOSTER FINS

ATTACH BOOSTER FINS

COMPLETE BOOSTER STAGE ASSEMBLY

FULL SIZED FIN ALIGNMENT TEMPLATE

MARK UPPER STAGE BODY TUBE

PREPARE AND ATTACH UPPER STAGE FINS

COMPLETE UPPER STAGE BODY TUBE ASSEMBLY

INSTALL UPPER STAGE ENGINE BLOCK

ASSEMBLE PAYLOAD BAY

ROCKET FINISHING

1. Spray rocket with white primer, let dry, and sand. Repeat until rocket is smooth.
2. Paint entire rocket white.
3. Mask off rocket except for one fin on the booster stage, one fin on the upper stage, and payload bay.
4. Paint fins and payload bay black. Apply decals only after paint is dry.
5. Cut decals from sheet, trimming close to edge.
6. One at a time, place in warm water until decal curls and begins to relax.
7. Remove and position on rocket, sliding decal away from backing material.
8. Blot with clean paper towel. Let set overnight.
9. OPTIONAL: Apply protective clear coat.

ATTACH SHOCK CORD

ATTACH NOSE CONE AND DOUBLE STREAMERS

PREPARE FLIGHT RECOVERY

PREPARE ENGINES

CENTER OF GRAVITY DIAGRAM

INSERT STARTER AND PLUG

COUNTDOWN AND LAUNCH

PRECAUTIONS

PRE-LAUNCH CHECK For safety, never launch a damaged rocket. Check the rocket’s body, nose cone and fins. Also, check the engine mount, recovery system and launch lug(s). Repair any damage before launching the rocket.
FLYING YOUR ROCKET Choose a large field (1000 ft. [305 m] square) free of dry weeds and brown grass. The larger the launch area, the better your chance of recovering your rocket. Launch only with little or no wind and good visibility. Always follow the National Association of Rocketry (NAR) SAFETY CODE (enclosed).
MISFIRES TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE GOING NEAR THE ROCKET. Disconnect the micro-clips and remove the engine. Take the plug and starter out of the engine. A burned starter means the starter tip was not touching engine propellant. Install a new starter; be sure the tip is touching propellant inside the engine. Push the plug in place. Repeat steps under Countdown and Launch.

© 2022 Estes Industries, LLC • All Rights Reserved
Estes Industries, LLC • 1295 H Street, Penrose, CO 81240-9698 • Made in Guangdong, China

References

• Estes Rockets

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>