ESTES 1713 Starseeker Bulk Pack Instruction Manual
- June 1, 2024
- ESTES
Table of Contents
ESTES 1713 Starseeker Bulk Pack
Product Information
Specifications
- Product Name: StarSeekerTM Model Rocket
- Manufacturer: EstesRockets.com
- Length of Launch Controller Wire: 16.4 ft (5 m)
- Recommended Engines: A3-4T, A10-3T, 1/2A3-2T
- Supplies Included: Fins, Nose cone halves, Body tube halves, Engine tube, Engine cap, Streamer
MODEL ROCKET INSTRUCTIONS
KEEP FOR FUTURE REFERENCE •
IMPORTANT: Please record the date found on the decal and keep it for
future reference.
READ ALL INSTRUCTIONS. Make sure you have all parts and supplies. Test
fit all parts before applying glue. Sand as necessary for precision assembly.
Product color and shape may vary.
ASSEMBLE
ASSEMBLE NOSE CONE
- Snap together C and D.
ATTACH SHOCK CORD
- Tie a double knot at one end of H.
- Pass the other end of H through the slit at the top of F. Pull H through until the double knot stops at the slit.
INSTALL ENGINE TUBE
ATTACH FINS
- Place on a flat surface and position both A on the assembly. Make sure you are not covering peg holes. Press down to hold in position.
- Align E and G and snap together. Make sure fins stay in position
- Insert B into slots and slide forward to lock into place.
ATTACH SHOCK CORD AND STREAMER
APPLY DECAL
NOTE: The decal must be applied as it reinforces the body tube seams.
PREPARE FLIGHT RECOVERY
NOTE: Only Estes® Recovery Wadding is recommended. Recovery wadding and streamer must slide easily into the body tube. If too tight, redo
PREPARE ENGINE
WARNING: To avoid serious injury, read the instructions & NAR Safety Code included with engines. PREPARE YOUR ENGINE ONLY WHEN YOU ARE OUTSIDE AT THE LAUNCH SITE PREPARING TO LAUNCH. If you do not use your prepared engine, remove the starter before storing your engine.
FULLY EXTEND YOUR LAUNCH CONTROLLER WIRE BEFORE LAUNCHING
NOTE: The key is always out until the final countdown!
ESTES® LAUNCH SUPPLIES NEEDED (Sold Separately)
- Launch Pad
- Launch Controller
- Recovery Wadding
- Starters (with engines)
- Plugs (with engines)
- Estes® Engines: 1/2A3-2T (first launch), A3-4T, A10-3T
PRECAUTIONS
NAR SAFETY CODE
NO DRY GRASS OR WEEDS
- PRE-LAUNCH CHECK For safety, never launch a damaged rocket. Check the rocket’s body, nose cone and fins. Also, check the engine mount, recovery system and launch lug(s). Repair any damage before launching the rocket.
- FLYING YOUR ROCKET Choose a large field (500 ft [152 m] square) free of dry weeds and brown grass. The larger the launch area, the better your chance of recovering your rocket. Football fields and playgrounds are great. Launch only with little or no wind and good visibility. Always follow the National Association of Rocketry (NAR) SAFETY CODE.
- MISFIRES TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE GOING NEAR THE ROCKET! Disconnect the starter clips and remove the engine. Take the plug and starter out of the engine. If the starter has burned, it worked but did not ignite the engine because it was not touching the propellant inside the engine. Put a new starter inside the engine without bending it. Push the plug in place. Repeat the steps under Countdown and Launch.
© 2017-2019 Estes Industries, LLC. All rights reserved.
FAQ
Q: Can I use different engines than the recommended ones?
A: It is recommended to use the engines specified in the manual for optimal performance and safety.
Q: What should I do if a part is too loose or too tight?
A: If a part is too loose, consider adding some adhesive or tape for a better fit. If it's too tight, sand it down slightly for a smoother assembly.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>