nVent 8P4I CADDY Push In Conduit Clamp Owner’s Manual
- August 7, 2024
- nVent
Table of Contents
nVent 8P4I CADDY Push In Conduit Clamp
Product Usage Instructions
Installation Steps
- Identify the suitable location for the conduit clamp.
- Ensure the conduit size matches the compatibility of the clamp (1/2 EMT).
- Push-in the conduit into the clamp until secure.
- Verify that the conduit is properly aligned for vertical or horizontal installation.
- If needed, thread the clamp for additional security.
Maintenance and Safety Tips
- Regularly inspect the clamp for any signs of wear or damage.
- Avoid exceeding the maximum diameter limit of the clamp (0.866 inches).
- Follow all safety precautions outlined in the product manual to prevent accidents.
Removal Instructions
- Unthread the conduit clamp if threaded for removal.
- Gently pull out the conduit from the clamp.
- Inspect the clamp for any remaining debris or damage after removal.
Cleaning and Storage Recommendations
- Clean the clamp with a mild detergent and water solution if needed.
- Store the clamp in a dry and cool environment to prevent corrosion.
- Avoid storing near sources of excessive heat or moisture.
FAQ
Frequently Asked Questions
- Q: Can this conduit clamp be used for outdoor installations?
- A: The product is suitable for indoor use. For outdoor installations, consult with nVent customer service for appropriate options.
- Q: What is the maximum load capacity of this conduit clamp?
- A: The load capacity may vary based on installation conditions. Refer to the product documentation for load capacity details or contact nVent customer service.
- Q: Is additional hardware required for installing this conduit clamp?
- A: The clamp is designed for easy installation without additional hardware. Ensure proper alignment and compatibility with the conduit size.
OVERVIEW
CATALOG NUMBER
- 8P4I
FEATURES
- Push-in installation of conduit
- Eliminates need for offset bending conduit
- May be used for either vertical or horizontal installations
PRODUCT ATTRIBUTES
- Material: Spring Steel
- Finish: nVent CADDY Armour
- EMT Conduit Size: 1/2″
- Outer Diameter: 0.71 – 0.87″
- Hole Size: 1/4″
- Hole Type: Threaded
- Ultimate Static Load 1: 25 lb
- Ultimate Static Load 2: 15 lb
DIAGRAMS
WARNING
nVent products shall be installed and used only as indicated in nVent’s
product instruction sheets and training materials.
Instruction sheets are available at www.nvent.com and from your nVent customer
service representative. Improper installation, misuse, misapplication or other
failure to completely follow nVent’s instructions and warnings may cause
product malfunction, property damage, serious bodily injury and death and/or
void your warranty.
Contacts
North America
- +1.800.753.9221
- Option 1 – Customer Care
- Option 2 – Technical Support
Europe
- Netherlands:
- +31 800-0200135
- France:
- +33 800 901 793
Europe
- Germany:
- 800 1890272
- Other Countries:
- +31 13 5835404
APAC
- Shanghai:
- + 86 21 2412 1618/19
- Sydney:
- +61 2 9751 8500
Our Brands
Our powerful portfolio of brands
- CADDY
- ERICO
- HOFFMAN
- RAYCHEM
- SCHROFF
- TRACER
© 2024 nVent. All nVent marks and logos are owned or licensed by nVent
Services GmbH or its affiliates. All other trademarks are the property of
their respective owners.
nVent reserves the right to change specifications without notice.
References
- Building a more Sustainable and Electrified World | nVent
- Building a more Sustainable and Electrified World | nVent
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>