atx GOBO Beam 100W LED Moving Head User Manual

GOBO Beam
100W LED Moving Head
Item ref: 150.463UK
User Manual

GOBO Beam 100W LED Moving Head

Please read through this manual thoroughly before use, any damage caused by misuse of product will not be covered by warranty.

Feature packed moving head that combines a bright 100W LED with 7 GOBOs, 7 colour wheels and a prism for the very best in effects and colour mixing. Featuring auto or sound-to-light modes, this 9 or 13 channel DMX light effect can be free standing or mounted to trussing using the supplied brackets. Ideal for stages, bars, nightclubs and mobile DJs the QTX GOBO Beam provides an array of colourful effects perfect for brightening up any occasion.

In the box:

Your GOBO Beam should arrive with you in a single carton in good condition. The carton should contain 1 x main unit with brackets, 1 x UK IEC mains lead and 1 x manual.
Warning:
To prevent risk of fire or electric shock, do not expose the unit to rain or damp environments. In the event of a spillage, disconnect the mains and allow the unit to dry out naturally. Qualified personnel should then check the unit before continuing use.
Please do not open cover, contains high voltage. This product is not serviceable or repairable by the end user. Please refer to qualified personnel for service and repair.

Placement:

• Use the included mounting brackets to fix to a stand or lighting truss.
• Use secondary safety fixings if mounting overhead.
• Keep away from damp or dusty environments.
• Ensure adequate airflow around the fixture housings.
• Ensure adequate access to controls and connections.
• Do not aim LED output directly into line of sight, as this can result in eye injury.

Cleaning:

• Use a soft cloth with a neutral detergent to clean the casing as required.
• Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups.
• Do not use strong solvents for cleaning the unit.

Rear panel and control:

1. LCD display
2. Menu button
3.  Up button
4. Down button
5. Enter button
6. Power input (IEC)
7. DMX input
8. DMX output

Manual control menu:

Press the “MENU” button to enter the settings menu.
Press “UP” and “DOWN” buttons to navigate through various setting functions.
Press “ENTER” button to confirm the desired setting.

CHnd

| 13ch| 13CH mode
9ch| 9CH mode
Angl| pan| p540/p270/p180/p90 (pan angle options)
tilt| t200/t180/t90 (tilt angle options)

SLnd

| Sl01| Slave mode
Auto| Auto mode
Sound| Sound control

SHnd

| Sh 0| Show 1
Sh 1| Show 2
Sh 2| Show 3
Sh 3| Show 4
SEnS| 10-100| Sound sensitivity

LEd

| OFF| Screen saver off
ON| Screen saver on

disp

| OFF| Screen reverse off
ON| Screen reverse on

rPAn

| OFF| Pan reverse off
ON| Pan reverse on

rtiL

| OFF| Tilt reverse off
ON| Tilt reverse on
rEst| YES| Reset
tenp| xxx| Temperature detection

DMX mode:
Your GOBO Beam can be controlled by DMX signal, simply connect the DMX signal source to the DMX input on the unit via a balanced XLR lead. Extra fixtures can be controlled by the same DMX signal by looping through the DMX out on the unit. To enter DMX mode, select A001 from the menu and confirm the correct start address by using the “UP” and “DOWN” buttons and “ENTER”. The A on the LED display will begin to flash once it’s received the DMX signal from the controller. This unit has either 9 or 13 DMX channels as indicated in the table below:
9/13 Channel DMX Table:

Specifications:

Troubleshooting:

No power (mains)| Check mains voltage is correct and outlet is switched on
---|---
Check IEC lead and fuse (if fuse continually blows, refer to your dealer)
No light output| Check control panel mode settings
Check DMX settings from controller (dimmer levels, blackout etc.)
**** Unresponsive to DMX| Check that unit is in DMX mode and ensure the A on the DMX address flashes to confirm it’s receiving a DMX signal
Check DMX controller is not set to black out
Check DMX controller is on correct fixture/page
Check master dimmer value
Check correct DMX address is set
Check DMX connection and leads
Overheating/Cutting out| Ensure adequate ventilation and unit is not too close to a heat source

This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2024 AVSL Group Ltd, Unit 2 Bridgewater Park, Taylor Road, Trafford Park, Manchester. M41 7JQ.
AVSL (Europe) Ltd, Unit 3D North Point House, North Point Bus. Park, New Mallow Road, Cork, Ireland.

www.avsl.com
150.463UK User Manual

References

• AVSL
• AVSL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>