A-NEUVIDEO ANI-PIP-21UHD 4K60 2×1 Multiviewer Seamless UHD Video Switcher User Manual

: August 9, 2024
: A-NEUVIDEO

A-NEUVIDEO ANI-PIP-21UHD 4K60 2×1 Multiviewer Seamless UHD Video Switcher

Specifications

Product Model: ANI-PIP-21UHD
Description: 4K60 2×1 Multiviewer Seamless UHD Video Switcher
Manufacturer: A-NeuVideo.com
Location: Frisco, Texas 75036

Product Information

The ANI-PIP-21UHD is a high-definition video switcher designed to seamlessly switch between two input sources and display them in a multiview format. It supports resolutions up to 3840×2160@60 and various audio formats, offering a versatile and immersive viewing experience.

FAQ

Q: Can I clean the unit with chemical solvents?

A: No, it is not recommended to clean the unit with chemical solvents as it may damage the device. Dusting with a clean dry cloth is sufficient for maintenance.

Q: What audio formats are supported by the switcher?

A: The switcher supports LPCM, AC3, DD+, DTS, DTSHD audio formats with up to 7.1 channel pass-through function via HDMI cable.

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make sure the following items are contained included:

4K60 2×1 Multiviewer Seamless UHD Video Switcher
IR Remote
3pin-3.81mm Phoenix Connector (male)
38KHz IR Wideband Receiver Cable (1.5 meters)
(2) Mounting Ears
(4) Machine Screws (KM3*4)
12V/1A Locking Power Adapter

SAFETY INFORMATION

To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference.
Follow all instructions printed on unit chassis for proper operation.
To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.
AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.
Turn power off and disconnect unit from AC current before making connections.
Never hold a power switch in the “ON” position.
This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.
When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.
Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.
Service Information Equipment should be serviced by qualified service personnel when:
- A. The power supply cord or the plug has been damaged.
- B. Objects have fallen, or liquid has been spilled into the equipment.
- C. The equipment has been exposed to rain.
- D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
- E. The equipment has been dropped, or the enclosure damaged.
  THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY IN- STRUCTIONS CONTAINED WITHIN THIS MANUAL.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.
© Copyright 2023. All Rights Reserved.
Version 1.1 JAN 2024

TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

INTRODUCTION

This 4K60 2×1 Multiviewer Seamless UHD Video Switcher was developed for the purpose of supporting higher output resolution (4K@60) for multiple sources on a single screen. It can combine two video signals onto a single UHD or HD displayer. The user can manage each input, and create combinations of the two inputs on a single display, as well as adjust the position of either input. This product supports (4) display modes, within the mode range, users can freely switch 2-channel HD input signals. It can realize single screen display and multiview display on a single screen. This device supports full range of input video resolutions up to 4K@60 (RB) and audio RCA /Optical de-embedding supported for external audio distribution systems. This device can be controlled via front panel buttons, IR remote, OSD menu navigation, Controller software, RS-232 commands.

FEATURES

HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
Support 18Gbps video bandwidth
Input and output resolutions support up to 4K2K@60 4:4:4
Support LPCM, AC3, DD+, DTS, DTS-HD, up to 7.1 audio channel
Seamless switching between input channels and combined multiple images on single UHD monitor
Up to (4) display modes: SINGLE, PIP, PBP (1), PBP (2)
Audio de-embedding via analog and optical fiber audio ports
Support volume control and independent audio selection
Advanced EDID management
Control via front panel buttons, IR remote, OSD menu navigation, Controller software, RS-232 commands
Compact design for easy and flexible installation

SPECIFICATIONS

Input Ports: (2) HDMI IN [Type A, 19-pin female]
Output Ports: HDMI OUT [Type A, 19-pin female]
L/R OUTPUT [RCA]
OPTICAL OUTPUT (TosLink)
Control Ports:
RS-232 [3pin-3.81mm phoenix connector]
IR EXT [3.5mm Stereo Mini-jack]
HDMI Compliance: HDMI 2.0b
HDCP Compliance: HDCP 2.2 / 1.x
Video Bandwidth: 18Gbps
Video Resolution: Up to 4K2K@60 4:4:4
IR Level: 5Vp-p
IR Frequency: 38KHz
Color Space: RGB, YCbCr 4:4:4, YCbCr 4:2:2, YCbCr 4:2:0
Color Depth: 8 bpc (24 bit total)
Audio Formats:
HDMI: PCM2.0/5.1/7.1CH, Dolby Digital/Plus, DTS, DTS High Res
Analog audio [3.5mm L/R]: PCM2.0
TosLink (OPTICAL): Dolby Digital, DTS 5.1, PCM2.0
Note: It does not support HBR audio.
ESD Protection: Human Body Model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Housing: Metal Enclosure
Color: Black
Dimensions (WxDxH): 6.9 x .22 x 1.2 in (175x100x30mm)
Weight: 1.1 lb / 497g
Operating Temperature: 0°C~40°C/ 32°F~104°F
Storage Temperature: −20°C ~ 60°C/−4°F ~140°F
Relative Humidity: 20~90% RH (non-condensing)
Power Consumption (Max): 4.56W (Max)
Power Supply: Input: AC 100 – 240V 50/60Hz / Output: DC 12V/1A (US/EU standard, CE/FCC/UL certified)
As product improvements are continuous, specifications are subject to change without notice

OPERATION CONTROLS & FUNCTIONS

Front Panel

POWER BUTTON: Press this button to power on the device. Hold down this button for 1 second to enter the standby mode.
POWER LED: The Power LED will light green when the product is powered on, and red when on standby.
INPUT 1-2 LEDS: Input signal indicator lights. When the HD 1/2 ports are connected to an active source device, the corresponding green LED will be on.
Note: Only the LED of the selected input channel will light in green on single screen display mode; all LEDs will light in green on multiview mode.
IR WINDOW: IR signal receiving window.
INPUT BUTTON: Input source button, only available on single screen display mode.
MULTIVIEW BUTTON: Multiview display mode button.
- Press this button to circularly select: SINGLE – PIP – PBP (1) – PBP (2).
- Hold down this button for 3 seconds to select the aspect ratio for PBP (1) / PBP (2).
RES BUTTON: Output resolution switching button.
- Press the RES button to circularly switch the output resolution of the HDMI OUTPUT port (Please refer to the output resolution list of “8. Video & Audio”).
- Hold down the RES button for 3 seconds to switch the output resolution to 720P60.

BACK PANEL

L/R PORT: PCM2.0 Analog audio output port.
OPTICAL PORT: Optical fiber digital audio output port.
HDMI OUTPUT PORT: HDMI output port, connected to a HDMI display device such as a TV or Monitor with a HDMI cable.
HD 1-2 INPUT PORTS: HDMI signal input ports, connected to HDMI source devices such as a DVD or Set-top box with a HDMI cable.
RS-232 PORT: 3-pin phoenix connector, connected to a PC or control system for serial port upgrade or RS-232 command control.
IR EXT PORT: IR signal receiving port, connected with a 38KHz IR Receiver cable. If the IR signal receiving window of the unit is blocked or the unit is installed in a closed area out of infrared line of sight, the IR receiver cable can be inserted to the “IR EXT” port to receive the IR remote signal.
DC 12V: DC 12V/1A power input port.

Remote Control / IR Pin Definition

Remote Control

POWER ON OR STANDBY: Press this button to power on the switcher or set it to standby mode.
BAUD: Press this button to pop up OSD menu, then circularly select the serial port baud rate: 115200, 57600, 38400, 19200, 9600
MULTIVIEW DISPLAY MODE BUTTONS: Press these buttons to select the display mode: SINGLE – PIP – PBP (1) – PBP (2).
WIN1: These buttons are available in all modes. In single-screen display mode, press HD1/HD2/ button to directly/circularly select input source for the WIN1 screen, and the corresponding input LED on the front panel will light in green. In PIP / PBP(1) / PBP(2) display mode, press HD1/HD2/ button to directly/circularly select input source for the WIN1 screen, and both input LEDs on the front panel will light in green.
WIN2: These buttons are unavailable in single-screen display mode. In PIP / PBP(1) / PBP(2) mode, press HD1/HD2/ button to directly /circularly select input source for the WIN2 screen, and both input LEDs on the front panel will light in green.
SET: In PIP mode, press POS to change the position of sub window; press SIZE to zoom in/out the size of the sub-window. In PBP(1) / PBP(2) mode, press 16:9 to switch the aspect ratio between 16:9 and FULL.
AUDIO: Press A-IN to switch between the two HDMI input audio sources. Press MUTE to mute /unmute the audio output. Press VOL- / VOL+ to increase/decrease the audio output volume.
RESOLUTION: Press 4K, 1080P, 720P or XGA to select output resolution.
EDID: Press 4K2.0, 4K5.1, 2K2.0 or COPY to select EDID mode.

IR Pin Definition

IR Receiver pin’s definition is as below:

IR CODES / EDID Settings / Video & Audio

IR CODES

Power Toggle	08F7 4D		WIN2 HD1	08F7 19
Baud	08F7 0B	WIN2 HD2	08F7 0F	Resolution 1080	08F7 44
Multiview-Single	08F7 09	WIN2 Cycle	08F7 03	Resolution 720	08F7 50
Multiview-PIP	08F7 54	SET POS	08F7 57	Resolution XGA	08F7 0E
Multiview-PBP (1)	08F7 47	SET SIZE	08F7 4E	EDID 4K2.0	08F7 18
Multiview-PBP (2)	08F7 42	SET 16:9	08F7 17	EDID 4K5.1	08F7 45
WIN1 HD1	08F7 48	Audio Mute	08F7 0D	EDID 2K2.0	08F7 14
WIN1 HD2	08F7 4B	Audio Vol-	08F7 56	EDID copy	08F7 51
WIN1 Cycle	08F7 43	Audio Vol+	08F7 16

EDID Settings
User can select following EDID modes via RS-232 command or OSD menu navigation.

No.| EDID Mode| | No.| EDID Mode| | No.| EDID Mode
---|---|---|---|---|---|---|---
1| 4K60-2.0CH| 8| 1080P-5.1CH| 15| 1280×1024-2.0CH
2| 4K60-5.1CH| 9| 1080P-7.1CH| 16| 1024×768-2.0CH
3| 4K60-7.1CH| 10| 1920×1200-2.0CH| 17| 720P-2.0CH
4| 4K30-2.0CH| 11| 1680×1050-2.0CH| 18| AUTO
5| 4K30-5.1CH| 12| 1600×1200-2.0CH| 19| USER1
6| 4K30-7.1CH| 13| 1440×900-2.0CH| |
7| 1080P-2.0CH| 14| 1360×768-2.0CH| |

Video & Audio
The switcher supports multiple resolution video inputs up to 3840×2160@60, and supports multiple audio formats such as LPCM, AC3, DD+, DTS, DTSHD, up to 7.1 channel pass through function via a HDMI cable. Control the volume of audio in LPCM format.
The switcher supports following video output resolutions via a powerful scaling engine.

No.	EDID Mode		No.
1	4096x2160p 60Hz	8	1920x1080p 60Hz
2	4096x2160p 50Hz	9	1920x1080p 50Hz
3	3840x2160p 60Hz	10	1360x768p 60Hz
4	3840x2160p 50Hz	11	1280x800p 60Hz
5	3840x2160p 30Hz	12	1280x720p 60Hz
6	3840x2160p 25Hz	13	1280x720p 50Hz
7	1920x1200p 60Hz RB	14	1024×768 60Hz

Multiview
The switcher supports 4 categories of multiview display modes: SINGLE, PIP, PBP (1), PBP (2) Users can select different operations for different multiview modes as following:
SINGLE: Inputs selection
PIP: Inputs selection, Sub window size and position selection
PBP (1), PBP (2): Inputs selection,
Display mode selection, Display aspect selection Multiview window distributions are as following:

User can select multiview display modes via IR remote, RS-232 commands or Controller software.

OSD Menu Navigation
A total of four buttons on the IR Remote are used for audio setting on OSD menu navigation, including Baud, Mute, VOL-, VOL+.
Menu contents are as follows:

Baud	Baud rate	115200	115200,57600,38400,19200,9600
Mute	Audio Mute	OFF	ON, OFF
VOL-/VOL+	Audio Volume	100	0..100

Controller Software Operation Guide

Installation & Connection
Follow the steps below to install the Controller software.

Step 1. Double-click the following driver to install the Controller software.
Step 2. Select “Anyone who uses this computer (all users)”, and then click “Next”.
Step 3. Select the installation path and click “Install”. After the installation is completed, click “Finish” to start using the Controller software.

Follow the steps below to connect the Controller software and the device.

Step 1. Connect the RS-232 port of the switcher to a PC with an RS-232 serial cable and an USB to RS-232 serial cable, as shown in the figure below.
Step 2. Launch the installed Controller software. (The default language is English, and you can set the language on the upper right corner of the main page.) Select “COM Control Mode” on the “General” page, then select the Port number and Baud Rate (default: 115200), and finally click “Connect”.

After successful connection, the “General” page will display the relevant information of the connected device, and the status bar at the bottom will display “Connected”.

Controller Main Interface General Page

You can do the following operations on the General page:

CONTROL MODE SELECT: Select the “COM Control Mode”. (TCP/IP control is not supported temporarily, so the TCP/IP Control Mode is disabled.)
COM CONTROL MODE: Select the Port number and Baud Rate of the device.
DEVICE INFORMATION: Display the device name, version and input/output connection status. Click “Device Status” to refresh the device status.
CONNECTION: Click to set the connection status.
CONNECTED: Display the connection status.

Output Page

OSD Menu Navigation
You can do the following operations on the Output page:

MULTI-VIEW ADJUSTMENT: Click to select the desired screen display mode. There are four modes available: SINGLE-PIP-PBP(1)-PBP(2).
PIP ADJUSTMENT: In the PIP mode, you can switch the location and size of the PIP and set the user-defined PIP, as shown in the following table.
Size| Relative Position (Starting Position)| Height and Width of the Inner Frame
---|---|---
Small| Start Point X: 71 Start Point Y: 71| Width: 30

Height: 30

Middle| Start Point X: 61 Start Point Y: 61| Width: 40

Height: 40

Large| Start Point X: 51 Start Point Y: 51| Width: 50

Height: 50

User| Start Point X: 1-100 Start Point Y: 1-100| Width: 1-100

Height: 1-100

MULTI-VIEWER DISPLAY: Display the input and output.
SOURCE INPUT: Select the input signal source. You should select the window in “Multi-Viewer Display” firstly, and then click “HDMI 1/2” in “Source Input” to select a signal source, or click / to select the last/next signal source.
ASPECT: Click “Full Screen” or “16:9” to switch the display aspect. Only the following modes are available: PBP(1)-PBP(2).
AUTO SWITCH: Enable or disable the function of automatically switching input signal source, available only in SINGLE mode.
OUTPUT SETTING: Set the output resolution, video keep alive, PC/Video PQ, HDCP, audio source and audio output.

System Page

EDID MODE CONTROL: Click the drop-down list on the right to select EDID mode.
FIRMWARE UPGRADE: Click the folder icon on the right to import the firmware upgrade file, then click “Upgrade” to start upgrade. There will be a progress bar prompt during the upgrade process. When the progress bar reaches 100%, it indicates the upgrade is successful, and the device will be restarted automatically.
FACTORY RESET: Click “Reset” to reset the device to factory default settings.
SYSTEM REBOOT: Click “Reboot” to reboot the device.

RS-232 Commands

The product also supports RS-232 command control. Connect the RS-232 port of the product to a PC with an RS-232 to USB serial cable. Then open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below.

ASCII Commands

version!

System Initializing… Initialization Finished! MCU FW version x.xx.xx

SCALER FW version x.xx.xx

System Initializing… Initialization Finished! MCU FW version x.xx.xx

SCALER FW version x.xx.xx

|
reset!| Reset to factory defaults| reset!| Reset to factory defaults System Initializing…

Initialization Finished!

MCU FW version x.xx.xx SCALER FW version x.xx.xx

|
OUTPUT SETTING
s output

res x!

| Set Output Resolution (x=1~14)

1. 4096x2160p60,

2. 4096x2160p50,

3. 3840x2160p60,

4. 3840x2160p50,

5. 3840x2160p30,

6. 3840x2160p25,

7. 1920x1200p60RB,

8. 1920x1080p60,

9. 1920x1080p50,

10.1360x768p60,

11.1280x800p60,

12.1280x720p60,

13.1280x720p50,

14. 1024x768p60

| s output res 3!| out resolution: 3840x2160p60| 3840x2160p60
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
r output res!| Get output resolution| r output res!| out resolution: 3840x2160p60|
s output| set output hdcp(x=1~3)| s output hdcp| output HDCP: HDCP 1.4| HDCP1.4
hdcp x!| 1. HDCP 1.4| 2!| |
| 2. HDCP 2.2| | |
| 3. HDCP OFF| | |
r output

hdcp!

itc x!

| Set output video mode(x=1~2) 1: video mode

2: pc mode

EDID x!

| Set HDMI input EDID mode (x=1~19)

1. 4K2K60_444,Stereo Audio 2.0

| s input EDID 1!| input EDID: 4K2K60_444,

Stereo Audio 2.0

EDID!

| Get input EDID mode| r input EDID!| input EDID:4K2K60_444,

Stereo Audio 2.0

|
r input

EDID!

| Get input EDID mode| r input EDID!| input EDID:4K2K60_444,

Stereo Audio 2.0

|
s edid user1 00 FF FF

…!

| Set user1 EDID data| s edid user1 00 FF FF FF FF

…!

| user1 EDID data: 00 FF FF FF FF FF FF 00 ………|
r edid user1!| Get user1 EDID data| r edid user1!| user1 EDID data: 00 FF FF FF FF FF FF 00 ………|
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
AUDIO SETTING
s output

audio x!

| Set output audio source(x=0~4)

0. follow window 1 selected source

1. HDMI 1 input audio

2. HDMI 2 input audio

3. HDMI 3 input audio

4. HDMI 4 input audio

| s output audio

0!

| output audio: follow window 1 selected source| output audio: follow window 1 selected source
r output

audio!

vol+!

| output audio volume: 50|
s output audio vol-!| Decrease output audio volume| s output audio

vol-!

| output audio volume: 50|
s output audio vol x!| Set output audio volume value (x=0~100)| s output audio

vol 30!

| output audio volume: 30| 100
r output audio vol!| Get output audio volume| r output audio

vol!

| output audio volume: 30|
s output audio mute x!| Set output audio mute on/off (x=0~1)

0. mute off

1. mute on

| s output audio

mute 0!

| output audio mute: off| off
r output audio mute!| Get output audio mute on/off| r output audio

mute!

| output audio mute: off|
SINGLE SCREEN MODE SETTING
s auto

switch x!

| Enable/disable auto switch feature(x=0~1)

0. Disable auto switch

1. Enable auto switch

| s auto switch 0!| auto switch off| auto switch off
r auto

switch!

| Get auto switch feature| r auto switch!| auto switch off|
s in source

x!

| Route input source to output (1~4)

1. HDMI 1

2. HDMI 2

3. HDMI 3

4. HDMI 4

| s in source 1!| HDMI 1| HDMI 1
r in source!| Get output secected input source| r in source!| HDMI 1|
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
MULTI-VIEWER MODE SETTING
s multiview

x!

| Set multi-viewer display mode (x=1~3)

1. single screen

2. PIP

3. PBP

in y!

| Select one input for one display window for the current Multiview mode.

(x=1~2)

1. window 1

2. window 2 (y=1~2)

1. HDMI 1

2. HDMI 2

| s window 1

in 1!

| window 1 select HDMI 1|
r window

x in!

| Get windows selected input source (x=0~2)

0. ALL

1. window 1

2. window 2

| r window 1 in!| window 1 select HDMI 1|
s window x

border y!

| Set the border mode of the

specified window.

(x=1~2)

1. window 1

2. window 2 (y=0~1)

0. off

1. on

| s window 1

border 1!

| window 1 border on| off
r window x

border!

| Get the border mode of windows

(x=0~2)

0. ALL

1. window 1

2. window 2

| r window 1

border!

| window 1 border on|
s window x border color y!| Set the border color of the

specified window.

(x=1~2)

1. window 1

2. window 2 (y=1~9)

1. BLACK

2. RED

3. GREEN

4. BLUE

5. YELLOW

6. MEGENTA

7. CYNA

8. WHITE

9. GRAY

| s window 1

border color 1!

| window 1 border color:BLACK| YELLOW
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
r window x

border color!

| Get the border color of windows

(x=0~2)

0. ALL

1. window 1

2. window 2

| r window 1

border color!

| window 1 border color:BLACK|
s PIP Hstart Vstart Hsize Vsize!| Set PIP window to user define

mode Hstart=(1~100) Vstart=(1~100) Hsize=(1~100) Vsize=(1~100)

NOTE:Hstart+Hsize<=101, Vstart+Vsize<=101

| s PIP 10 10 20

20!

| PIP 10 10 20 20|
s PIP

position x!

| Set PIP window position (x=1~5)

1. Left Top

2. Left Bottom

3. Right Top

4. Right Bottom

5. user

| s PIP position

3!

| PIP on right top| PIP on right top
r PIP

position!

1. small

2. middle

3. large

4. user

x!

| Set PBP windows display mode (x=1~2)

1. PBP mode 1

2. PBP mode 2

aspect x!

| Set PBP windows display aspect ratio (x=1~2)

1. Full screen 2. 16:9

| s PBP aspect

1!

| PBP aspect: full screen| PBP aspect: full screen
r PBP

aspect!

| Get PBP windows display aspect ratio| r PBP aspect!| PBP aspect: full screen|

Application Example

TERMS AND CONDITIONS OF USE

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.

DISCLAIMERS AND LIMITATION OF LIABILITY

A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT

Documents / Resources

| A-NEUVIDEO ANI-PIP-21UHD 4K60 2x1 Multiviewer Seamless UHD Video Switcher [pdf] User Manual
ANI-PIP-21UHD, ANI-PIP-21UHD 4K60 2x1 Multiviewer Seamless UHD Video Switcher, ANI-PIP-21UHD UHD Video Switcher, 4K60 2x1 Multiviewer Seamless UHD Video Switcher, 4K60 2x1 UHD Video Switcher, Multiviewer Seamless UHD Video Switcher, Seamless UHD Video Switcher, Seamless Video Switcher, UHD Video Switcher, Video Switcher, Switcher
---|---