AMUSEMENT CONNECT MobileMech Mobile Transceiver Installation Guide
- August 6, 2024
- AMUSEMENT CONNECT
Table of Contents
AMUSEMENT CONNECT MobileMech Mobile Transceiver
2024
MobileMech
INSTALLATION AND USER INSTRUCTIONS
For Assistance Call 833-727-2233 x2
PARTS LIST
- Motherboard
- Shell Case
- Base Wiring Harness
- 9-Pin Bill Validator Harness
- Spike Harness – Alternative 12V Source
- 12V Power Supply Install – Alternative 12V Source
- 3 Pin BV Harness – Alternative BV (Optional)
- Slider Mech 2 Wiring Harness for Pool Table
Motherboard
Shell Case
Base Wiring Harness
9-Pin Bill Validator Harness
Spike Harness – Alternative 12V Source for Pinball (Optional)
12V Harness – Alternative 12V Source (Optional)
3 Pin BV Harness – Alternative BV harness for Raw Thrills Games (Optional)
Slider Mech 2 Harness (Optional)
SPECS
BASE WIRING HARNESS
Pin Out
| Pin | Function | Wire Color |
|---|---|---|
| 1 | GND | Black |
| 2 | GND | Black |
| 3 | GND | Black |
| 4 | GND | Black |
| 5 | GND | Black |
| 6 | Relay Common | Black |
| Pin | Function | Wire Color |
| --- | --- | --- |
| 7 | +12V | Red |
| 8 | AUX | White |
| 9 | COINl | Yellow |
| 10 | BV | Blue |
| 11 | CCD | Purple |
| 12 | RElAY | Org/Wht |
Wire Gauge to be 20 AWG Stranded Copper Wire
9-PIN BV WIRING HARNESS
Pin Out
Note: Jumper between pin 6 a rod pin 9 on connector 172169-1
SPIKE WIRING HARNESS
Wire Gauge to be 22 AWG Stranded Copper Wire
12V WIRING HARNESS
3-PIN BV WIRING HARNESS
Wire Gauge to be 20 AWG Stranded Copper Wire
SLIDERMECH 2 WIRING HARNESS
Pin Out
| Pin | F unction | Wire Color |
|---|---|---|
| 1 | ||
| 2 | Ground | Black |
| 3 | Sensor Signal | White |
| 4 | +12V | Red |
Wire Gauge to be 20 AWG Stranded Copper Wire
INSTALLATION
Base Wiring Harness Install – Coin Mechs (1 or 2 ct.)
- Locate the coin wires and disconnect from coin mechanism.
- Locate yellow/black coin 1 / 2 wire set on the Base MobileMech Harness and connect to the coin mechanism.
Base Harness Install – Coin Pulse Output
- Locate the one pair of coin pulse wires going to the game, these were disconnected during the Base Harness Install – Coin 1 / 2 Input.
- Locate orange/black Coin Pulse Output wire pair on the Base MobileMech Harness and connect to the coin pulse wires going to the game.
Base Harness Install – Bill Validator Input
- Locate the 9 pin bill validator wires and disconnect.
- Locate the 9-Pin BV Validator Harness. Connect both 9-Pins to the 9-pin connector coming from the game and to the BV.
- Locate the blue/black BV Input wires on the Base MobileMech Harness and connect to the corresponding blue/blk wires on the 9-Pin BV Harness.
- Locate the red/black 12Volt Power wires on the Base MobileMech Harness and connect to the corresponding red/black wires on the 9-Pin Harness.
Note: If the BV is a 110V model then disconnect the 12V red/black wires from the BV harness. In this case the 12V can be connected using an add-on harness.
Base Harness Install – CCD Input (Credit Card)
- Locate the pulse wires and disconnect from the credit card device.
- Locate purple/black CCD Input wire pair on the base Mobile Mech harness and connect to the coin mechanism using wire nuts.
- Note: You will need to strip the purple/black wire pair and expose the wiring in order to connect.
Base Harness Install
- After connecting all other harnesses, connect the MobileMech to the black 12-Pin connector on the harness. The Red LED light will turn on if connected correctly.
- Secure the Base Harness Wires and MobileMech. Tidy up wires, we suggest using zip ties.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>