STAIRVILLE 70th Stage TRI LED Bundle Complete User Manual

70th Stage TRI LED Bundle Complete

70th Stage TRI LED Bundle Complete

User ManualLED Lighting Set

Thomann GmbH

Hans-Thomann-Straße 1 96138 Burgebrach

Germany

Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de

12.03.2024, ID: 582646

70th Stage TRI LED Bundle Complete

LED Lighting Set 3

1 General information

This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future reference. Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this document.

Our products and documentation are subject to a process of continuous development. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de.

1.1 Symbols and signal words

In this section you will find an overview of the meaning of symbols and signal words that are used in this document.

70th Stage TRI LED Bundle Complete
LED Lighting Set 5

General information

Signal word Meaning

DANGER! This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided.

WARNING! This combination of symbol and signal word indicates a possible dangerous situation that can result in death or serious injury if it is not avoided.

NOTICE! This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided.

Warning signs Type of danger

Warning – high-voltage.

Warning – hot surface.

Warning – dangerous optical radiation.

Warning signs Type of danger

Warning – suspended load.

Warning – danger zone.

70th Stage TRI LED Bundle Complete
LED Lighting Set 7

Safety instructions

2 Safety instructions

Intended use

This device is intended for use as an electronic lighting effect by means of LED technology. The device is designed for professional use only and is not suitable for use in households. Use the device only as described in this user manual. Any other use or use under other operating con‐ ditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.

This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Extend the operating life of the device by regular breaks and by avoiding frequent switching on and off. The device is not suitable for continuous operation.

Safety

DANGER!

Risk of injury and choking hazard for children!

Children can suffocate on packaging material and small parts. Children can injure themselves when handling the device. Never allow children to play with the packaging material and the device. Always store packaging material out of the reach of babies and small children. Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervision. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with.

870th Stage TRI LED Bundle Complete
LED Lighting Set

Safety instructions

DANGER!
Danger to life due to electric current!
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged.

DANGER!
Danger to life due to electric current!

A short circuit could lead to a fire hazard and risk of death. Always use proper ready-made insulated triple-core mains cable with a safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect immediately the power supply and arrange repair. If in doubt, seek advice from a qualified electrician.

WARNING!

Risk of eye damage caused by high light intensity!

The device generates highly intense light radiation. Looking directly into the light source can damage the eyes. Never look directly into the light source.

WARNING!

Risk of epileptic fit due to flashing lights!

The device emits flashing lights (strobe effects). Flashing lights can trigger epileptic fits in specific people. If you are at risk of epi‐ lepsy, avoid spending longer periods of time subjected to flashing lights and looking into strobing light.

WARNING!

Danger of burns on the device surface!

The surface of the device becomes very hot during operation. Skin contact can result in burns. Never touch the device with your bare hands during operation. After switching off the device, wait for at least 15 minutes before touching it.

70th Stage TRI LED Bundle Complete
LED Lighting Set 9

Safety instructions

NOTICE!

Risk of fire due to covered vents and neighboring“ heat sources!

If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can over‐ heat and burst into flames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other heat sources. Never operate the device in the immediate vicinity of naked flames.

NOTICE!

Damage to the device due to high voltages!

The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess vol‐ tages can also cause a risk of injury and fires. Make sure that the voltage specification on the device matches the local power grid before plugging in the device. Only operate the device from professionally installed mains sockets that are protected by a residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or it the device will not be used for a longer period.

NOTICE!

Damage to the device if operated in unsuitable ambient conditions!

The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the ambient conditions specified in the “Technical specifications” chapter of this user manual. Avoid operating it in environments with direct sun‐ light, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature fluctuations. If temperature fluctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in operation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by qualified specialists at regular intervals to prevent damage due to overheating and other malfunctions.

NOTICE!

Risk of fire due to installation of a wrong fuse!

Using fuses of a different type than compatible with the device may cause a fire and seriously damage the device. Only use fuses of the same type. Observe the labelling on the device casing and the information in the “Technical data” chapter.

10 70th Stage TRI LED Bundle Complete
LED Lighting Set

Safety instructions

NOTICE!

Risk of short circuit due to changing the connection wiring during operation!

If connection cables of individual spots are removed or replaced during operation, short circuits may occur that can irreparably damage the device. Always disconnect the device from the mains before making any changes to the wiring.

NOTICE!

Damage to the device by disconnecting LED spots during operation!

If individual LED spots are disconnected from the device during operation, the device can get damaged. Operate the device only when all LED spots are connected. Always disconnect the device from the mains before removing the LED spots.

NOTICE!

Risk of fire by exceeding the maximum current

The device can supply power to other devices of identical design and connected in series. If too many devices are connected, the power consumption can exceed the maximum permitted power consumption, which can cause the device to overheat and burst into flames. Only connect devices of identical design to the device. When deciding how many devices you can connect in series, make sure that the maximum permitted power consumption as stated on the device is not exceeded. Also refer to the specifications in the technical specifications for the device. Only use power cords with a cable cross-section designed for the required current intensity when connecting the devices in series.

NOTICE!

Possible staining due to plasticiser in rubber feet!

The plasticiser contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor.

NOTICE!

Risk of fire due to incorrect polarity!

Incorrectly inserted batteries may cause fires and destroy the device and the batteries. Observe the markings on the batteries and on the device. Ensure that proper polarity is observed when inserting batteries.

70th Stage TRI LED Bundle Complete
LED Lighting Set 11

Safety instructions

NOTICE!

Possible damage due to leaking batteries!

Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period of time.

12 70th Stage TRI LED Bundle Complete
LED Lighting Set

Features and scope of delivery

3 Features and scope of delivery

The LED lighting set is particularly suitable for professional lighting tasks, for example at events, on rock stages, in theatres and musicals. It has low power consumption and a long service life.

With this “all-in-one” LED set, Stairville is introducing a longed-for lighting solution for all bands, entertainers, musicians, magicians, cabaret artists and all those who need high-quality lighting on their stage with the lowest possible effort. The incredibly bright RGB TRI-Colour LEDs are currently the best that stage LED technology has to offer. All imaginable colours can be mixed, completely without RGB shadow. The very low power consumption and practically non-existent heat dissipation have convinced even the last critic. The Stage TRI LED Bundle Complete can be easily controlled via the supplied foot switch or DMX 512.

Special features of the device:

■ Special edition of the classic lighting set to mark Thomann’s 70th anniversary

■ Special edition with new innovative sound mode

■ 4 LED spots with 7 3 W RGB TRI-Colour LEDs each (28 in total)

■ Control via DMX 512 or foot switch (available via foot switch: automatic mode, sound-to light mode, freeze & blackout)

■ 6 DMX modes available (3, 4, 6, 12, 15 or 19 DMX channels)

■ LED display for setting parameters such as DMX address, DMX mode etc.

■ XLR in/output, 3-pin

■ Beam angle approx. 40°

70th Stage TRI LED Bundle Complete
LED Lighting Set 13

Features and scope of delivery

■ T-bar with 4 LED spots, lighting stand (max. height 240 cm), foot switch with 4 buttons,

transport bag for light and stand (included in the scope of delivery)

■ Remote control (item no. 354223, optionally available)

For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness.

14 70th Stage TRI LED Bundle Complete
LED Lighting Set

4 Installation

Installation

Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.

WARNING!

Risk of injury from falling devices that were inadequately secured!

If devices are not properly secured during assembly, they can cause severe injury and considerable damage by falling.

When installing and operating, make sure to follow the standards and regulations that apply in your country.

Always secure the device with a secondary safety attachment, such as a safety cable or a safety chain.

70th Stage TRI LED Bundle Complete
LED Lighting Set 15

Installation

16 70th Stage TRI LED Bundle Complete LED Lighting Set

NOTICE!

Damage to the device by disconnecting LED spots during operation! If individual LED spots are disconnected from the device during operation, the device can get damaged.

Operate the device only when all LED spots are connected.

Always disconnect the device from the mains before removing the LED spots.

NOTICE!

Risk of overheating and fire due to inadequate distance and bad ventilation! If the distance between the light source and the illuminated surface is too short or the device is badly ventilated, the device can overheat and cause fires.

Make sure that illuminated surfaces are more than 2 m away.

Do not operate the device in ambient temperatures above 40 °C. Always ensure sufficient ventilation at the operating location.

Installation

NOTICE!

Potential property damage due to unsuitable stands!

If the device is mounted on an unsuitable stand, there is a risk that the stand will fall over and cause damage.

Only use stands whose maximum bearing capacity is at least as high as the weight of the device. Always ensure that the stand is stable.

NOTICE!

Data transfer errors due to improper wiring!

If the DMX connections are wired incorrectly, this can cause errors during the data transfer.

Do not connect the DMX input and output to audio devices, e.g. mixers or ampli‐ fiers.

Use special DMX cables for the wiring instead of normal microphone cables.

70th Stage TRI LED Bundle Complete
LED Lighting Set 17

Installation

Pre-mounted spots

The four spots (1 … 4, left to right) are pre-mounted on the T-bar. All you need to do is attach the stand and connect the foot switch unit.

18 70th Stage TRI LED Bundle Complete
LED Lighting Set

Installation

1 Locking screws to fix the height and inclination angle

2 Threads for attaching additional effects units or for hanging using the C-hooks

3 Locking screw for fixing the spots on the T-bar and the horizontal orientation (dispersion direction)

4 Electrical connection of the spot at the T-bar (pre-mounted)

5 6.35-mm jack socket for connecting the foot switch unit. The cable with the phone socket is pre-mounted at the foot controller unit.

70th Stage TRI LED Bundle Complete
LED Lighting Set 19

Installation

Inserting the battery into the remote control

Push the lock of the battery holder towards the centre of the housing and pull out the battery holder like a drawer. Insert the batteries. The battery is correct if the positive pole points to the housing base of the remote control. Slide the battery holder back into the remote until it clicks into place.

When shipping, the battery is already installed in the remote and protected against discharge by a transparent plastic film. Remove the plastic film before initial use.

NOTICE!
Risk of fire due to incorrect polarity!

Incorrectly inserted batteries may cause fires and destroy the device and the batteries.

Observe the markings on the batteries and on the device.

Ensure that proper polarity is observed when inserting batteries.

NOTICE!
Possible damage due to leaking batteries!

Batteries can leak and cause permanent damage to the device.

Take the batteries out of the device if it is not going to be used for an extended period of time.

20 70th Stage TRI LED Bundle Complete LED Lighting Set

Installation

Please note that this device must not be connected to a dimmer.

70th Stage TRI LED Bundle Complete
LED Lighting Set 21

Starting up

5 Starting up

Create all connections while the device is off. Use the shortest possible high-quality cables for

all connections. Take care when running the cables to prevent tripping hazards.

Connections in DMX mode

Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device. Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 Ω, ¼ W).

22 70th Stage TRI LED Bundle Complete
LED Lighting Set

Starting up

Connections in master/slave mode

When you configure a group of devices in master/slave mode, the first unit will control the other units for an automatic, sound-activated, synchronized show. This function is ideal when you want to start a show immediately. Connect the DMX output of the master device to the DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on.

70th Stage TRI LED Bundle Complete
LED Lighting Set 23

Connections and controls

6 Connections and controls

Front panel

24 70th Stage TRI LED Bundle Complete
LED Lighting Set

Connections and controls

1 Rubber panel plug for the power supply with fuse holder

2 [Mic] | Built-in microphone for the “sound control” operating mode

3 [Mode] | Activates the main menu and toggles between menu items. Closes an open submenu.

4 Display

5 [DOWN] | Decreases the displayed value by one.

6 [Footswitch Input] | 6.35-mm jack socket for connecting the foot switch unit

7 [DMX In] | DMX input

8 [DMX Out] | DMX output

9 [Power Out] | Rubber panel sockets for the power supply cable to the next device of the same type

10 [IR] | Infrared receiver for the remote control signals. Make sure that the infrared sensor is not obstructed.

11 [Up] | Increases the displayed value by one.

12 [Setup] | Selects an option of the respective operating mode, confirms the set value.

70th Stage TRI LED Bundle Complete
LED Lighting Set 25

Connections and controls

Foot switch unit

(item no. 279058)

1 [Auto Run/Program] | Activates “Automatic” mode (playback of pre-programmed automatic shows).

2 [Sound Active] | Activates “Sound control” mode (playback of sound controlled automatic shows).

3 [Freeze] | Pauses the running show (“freeze”) and resumes it after a break.

4 [Blackout] | Blacks out all LEDs or turns them back on again.

26 70th Stage TRI LED Bundle Complete
LED Lighting Set

Infrared remote control

(item no. 354223, optionally available)

Connections and controls

Since the universal remote control can be used for several device types, some buttons may not be assigned and therefore have no function.

1 [AUTO] | Activates “Automatic” mode.

2 [ON/OFF] | Turns the device on and off.

3 [SOUND] | Activates “Sound control” mode. Set the sensitivity of the built- in micro‐ phone with [+] and [–].

4 [+] | Increases the set value.

5 [0 … 9] | Number buttons for the direct selection of a fixed colour.

6 [SPEED] | Activates the setting mode for the programme speed. Adjust the speed using [+] and [–].

7 [PRG] | Activates the “Pre-programmed automatic show” mode. Select the required programme with [+] and [–].

8 [STROBE] | Activates the setting mode for the strobe speed. Adjust the speed using [+] and [–].

9 [–] | Decreases the set value.

10 [Dimming] | Activates the dimming function for fixed colours. Set the value for each fixed colour using [+] and [–].

11 [R], [G], [B], [A], [W] | Buttons for selecting the colour shade in dimmer mode.

70th Stage TRI LED Bundle Complete
LED Lighting Set 27

Operating

7 Operating

7.1 Starting up the device

Connect the unit to the power grid to start the operation. After a few seconds the display shows a running reset. Then the unit is ready for use.

7.2 Main menu

Press [Mode] to activate the main menu and select an operating mode. Use [Setup] to select further options. Use [Up] and [Down] to change the currently displayed value. When the display shows the desired value, press [Mode].

If you do not press any button for about 30 seconds, the display turns off. Pressing any button reactivates the display, which will show the previously shown menu.

The set values are retained even when the device is disconnected from the mains power supply.

28 70th Stage TRI LED Bundle Complete
LED Lighting Set

“Pre-programmed automatic show” operating mode

Operating

A pre-programmed automatic show can only be activated if the device is operating in stand alone mode or as master in a master/slave combination. This setting is only relevant if the device is not controlled via DMX.

Press [Mode] repeatedly until the display shows ‘Pr.xx’ . Now you can select one of the pre-pro‐ grammed automatic shows. Use [Up] and [Down] to select a value between ‘Pr.01’ and ‘Pr.23’ . The following table shows the available programmes.

Programme Description

‘Pr.01’ Static colours

‘Pr.02’ … ‘Pr.23’ Colour change

Settings for programme 01:

For ‘Pr.01’ , you can choose from 15 colours. Press [Setup]. Now you can use [Up] and [Down] to select one of the colours.

Display Description

‘Co.00’ Black

‘Co.01’ Red

‘Co.02’ Green

70th Stage TRI LED Bundle Complete
LED Lighting Set 29

Operating

Display Description

‘Co.03’ Blue

‘Co.04’ Cold white

‘Co.05’ Amber

‘Co.06’ Orange

‘Co.07’ Yellow

‘Co.08’ Purple

‘Co.09’ Pink

‘Co.10’ Cyan

‘Co.11’ Light red

‘Co.12’ Light green

‘Co.13’ Light blue

‘Co.14’ Warm white

To adjust the flash frequency, press [Setup]. Now use [Up] and [Down] to select a value

between ‘FL.00’ (slow) and ‘FL.99’ (fast).

30 70th Stage TRI LED Bundle Complete LED Lighting Set

Operating

Settings for programmes 02 to 23:

“Automatic” operating mode

To adjust the speed of the selected auto show, press [Setup] repeatedly until the display shows ‘SP.xx’ . Now use [Up] and [Down] to select a value between ‘SP.01’ (slow) and ‘SP.99’ (fast) or ‘SPFL’ (Flash effect).

To adjust the flash frequency, press [Setup] repeatedly until the display shows ‘FL.xx’ . Now use [Up] and [Down] to select a value between ‘FL.00’ (slow) and ‘FL.99’ (fast).

Automatic mode can only be activated if the device is operating in stand-alone mode or as master in a master/slave combination. This setting is only relevant if the device is not con‐ trolled via DMX.

Press [Mode] repeatedly until the display shows ‘AUTO’ . Press [Setup]. Press [UP] or [Down] to choose between ‘AU.01’ … ‘AU.03’ .

Programme Description

‘AU.01’ Gentle effects

‘AU.02’ Dynamic effects

‘AU.03’ All effects of the “pre-programmed automatic show”

To adjust the speed, press [Setup]. Now use [Up] and [Down] to select a value between ‘SP.01’ (slow) and ‘SP.99’ (fast) or ‘SPFL’ (Flash effect).

To adjust the flash frequency, press [Setup]. Now use [Up] and [Down] to select a value between ‘FL.00’ (slow) and ‘FL.99’ (fast).

70th Stage TRI LED Bundle Complete
LED Lighting Set 31

Operating

DMX mode

“Slave” operating mode Sound control

In automatic mode the saved programmes run sequentially. Press the [AUTO] button several times to start the automatic sequence from a specific programme. There is however no way to permanently specify a specific programme as the starting programme.

This setting is only relevant when the device is controlled via DMX.

Press [Mode] until the display shows ‘d—’ .

Now you can set the number of the first DMX channel to be used by the device (DMX address). Use [Up] and [Down] to select a value between 1 and 512 (display shows ‘d.001’…‘d.512’ ).

Make sure that this number matches the configuration of your DMX controller. The following table shows the highest possible DMX address for the various DMX modes.

Press [Setup]. Now you can use [Up] and [Down] to select a DMX operating mode with 3 chan‐ nels, 4 channels, 6 channels, 12 channels, 15 channels and 19 channels.

This setting is only relevant if the device is serving as slave in a master/slave configuration and is not controlled via DMX.

Press [Mode] repeatedly until the display shows ‘SLAVE’ . Press [YES].

A sound-controlled show can only be activated when the unit is operating in stand alone mode or as master in a master / slave combination. This setting is only relevant if the device is not controlled via DMX.

Press [Mode] repeatedly until the display shows ‘SO.xx’ . Now use [Up] and [Down] to select a show between ‘SO.01’…‘SO.24’ . This activates a sound- controlled show.

32 70th Stage TRI LED Bundle Complete
LED Lighting Set

Operating

Display Description

‘SO.01’…‘SO.03’ Gentle effects

‘SO.04’…‘SO.21’ Dynamic effects

‘SO.22’ Collection of gentle effects ‘SO.23’ Collection of dynamic effects ‘SO.24’ Collection of all effects

Press [Setup]. Now you can adjust the sensitivity for the sound control. Use [Up] and [Down] to select a value between 0 (low sensitivity) and 50 (high sensitivity), display shows ‘SU.xx-FL(00)’ …‘SU.xx-FL(50)’ .

70th Stage TRI LED Bundle Complete
LED Lighting Set 33

Operating

Constant monochrome pattern

A constant monochrome pattern can only be activated when the unit is operating in stand alone mode or as master in a master / slave combination. This setting is only relevant if the device is not controlled via DMX.

Press [Mode] repeatedly until the display shows ‘Colr’ . Press [Setup].

Now use [Up] and [Down] to select one of the following options:

Display Meaning

‘r.000’ … ‘r.255’ Red

‘g.000’ … ‘g.255’ Green

‘b.000’ … ‘b.255’ Blue

34 70th Stage TRI LED Bundle Complete LED Lighting Set

Settings

Operating

Press [Mode] repeatedly until the display shows ‘Set’ .

Press [Setup]. Use [Up] and [Down] to select a setting.

Display Meaning

‘Cu.SE’ Dimmer curves

‘di.SP’ Dimmer speed

‘Pi.dl’ Running direction of the lights ‘-rst’ Restore factory setting

‘FAIL’ Behaviour in case of DMX signal failure ‘LocK’ Display lock

Press [Mode] repeatedly until the display shows ‘Cu.SE’ . Press [Setup]. You can choose between 4 dimmer curves.

Display Meaning

‘Cu-1’ Linear

‘Cu-2’ Square Law

70th Stage TRI LED Bundle Complete
LED Lighting Set 35

Operating Info

Display Meaning

‘Cu-3’ Inv Square Law

‘Cu-4’ S-Type

Press [Mode] repeatedly until the display shows ‘di.SP’ .

Press [Setup]. You can choose the speed ‘FASt’ (fast) or ‘SLO’ (slow).

Press [Mode] repeatedly until the display shows ‘Pi.dl’ .

Press [Setup]. Use [Up] and [Down] to select a setting between ‘Nor’ (normal) and ‘Inv’ (inverse)

Press [Mode] repeatedly until the display shows ‘-rst’ .

Press [Setup]. Select ‘YES’ to perform a reset to factory defaults. Select ‘NO’ to cancel, see also ⮲ Chapter 7.12 ‘Reset to factory defaults’ on page 55.

Press [Mode] repeatedly until the display shows ‘FAIL’ . Press [Setup]. Select ‘Off’ if the DMX connection has failed and you want to break the connection. Select ‘Hold’ if the DMX connec‐ tion has failed and you want to hold the connection.

Press [Mode] repeatedly until the display shows ‘LocK’ . Press [Setup]. Press ‘ON’ or ‘OFF’ to lock or unlock.

Press [Mode] repeatedly until the display shows ‘INFO’ . Press [Setup]. In the ‘Ver’ menu you can view the version number ‘v.x.x.x’ .

36 70th Stage TRI LED Bundle Complete
LED Lighting Set

7.3 Menu overview

70th Stage TRI LED Bundle Complete
LED Lighting Set 37

Operating

38 70th Stage TRI LED Bundle Complete
LED Lighting Set

7.4 Functions in 3-channel DMX mode

Channel Value Function

1 0…255 Red intensity (0% to 100%) for all LEDs 2 0…255 Green intensity (0% to 100%) for all LEDs 3 0…255 Blue intensity (0% to 100%) for all LEDs

7.5 Functions in 4-channel DMX mode

Channel Value Function

1 0…255 Dimmer (0% to 100%) 2 0…25 No function

26…35 Pre-programmed automatic show no. 02

36…45 Pre-programmed automatic show no. 03

46…55 Pre-programmed automatic show no. 04

56…65 Pre-programmed automatic show no. 05

66…75 Pre-programmed automatic show no. 06

Operating

70th Stage TRI LED Bundle Complete
LED Lighting Set 39

Operating

Channel Value Function

76…85 Pre-programmed automatic show no. 07 86…95 Pre-programmed automatic show no. 08 96…105 Pre-programmed automatic show no. 09 106…115 Pre-programmed automatic show no. 10 116…125 Pre-programmed automatic show no. 11 126…135 Pre-programmed automatic show no. 12 136…145 Pre-programmed automatic show no. 13 146…155 Pre-programmed automatic show no. 14 156…165 Pre-programmed automatic show no. 15 166…175 Pre-programmed automatic show no. 16 176…185 Pre-programmed automatic show no. 17 186…195 Pre-programmed automatic show no. 18 196…205 Pre-programmed automatic show no. 19 206…215 Pre-programmed automatic show no. 20 216…225 Pre-programmed automatic show no. 21 226…235 Pre-programmed automatic show no. 22

40 70th Stage TRI LED Bundle Complete
LED Lighting Set

Channel Value Function

236…245 Pre-programmed automatic show no. 23 246…255 Sound-controlled show

3 0…25 Sound-controlled show no. 01 26…35 Sound-controlled show no. 02

36…45 Sound-controlled show no. 03

46…55 Sound-controlled show no. 04

56…65 Sound-controlled show no. 05

66…75 Sound-controlled show no. 06

76…85 Sound-controlled show no. 07

86…95 Sound-controlled show no. 08

96…105 Sound-controlled show no. 09

106…115 Sound-controlled show no. 10

116…125 Sound-controlled show no. 11

126…135 Sound-controlled show no. 12

136…145 Sound-controlled show no. 13

146…155 Sound-controlled show no. 14

Operating

70th Stage TRI LED Bundle Complete LED Lighting Set 41

Operating

Channel Value Function

156…165 Sound-controlled show no. 15

166…175 Sound-controlled show no. 16

176…185 Sound-controlled show no. 17

186…195 Sound-controlled show no. 18

196…205 Sound-controlled show no. 19

206…215 Sound-controlled show no. 20

216…225 Sound-controlled show no. 21

226…235 Sound-controlled show no. 22

236…245 Sound-controlled show no. 23

246…255 Sound-controlled show no. 24

4 Function depending on setting of channel 2 Channel 2 = 0…25

No function

Channel 2 = 26…245

0…255 Increasing speed

42 70th Stage TRI LED Bundle Complete

LED Lighting Set

Operating

Channel Value Function

Channel 2 = 246…255

0…255 Increasing sensitivity

7.6 Functions in 6-channel DMX mode

Channel Value Function

1 0…255 Red intensity (0% to 100%) for all LEDs of spots 1 and 2

2 0…255 Green intensity (0% to 100%) for all LEDs of spots 1 and 2

3 0…255 Blue intensity (0% to 100%) for all LEDs of spots 1 and 2

4 0…255 Red intensity (0% to 100%) for all LEDs of spots 3 and 4

5 0…255 Green intensity (0% to 100%) for all LEDs of spots 3 and 4

6 0…255 Blue intensity (0% to 100%) for all LEDs of spots 3 and 4

70th Stage TRI LED Bundle Complete
LED Lighting Set 43

Operating

7.7 Functions in 12-channel DMX mode

Channel Value Function

1 0…255 Red intensity (0% to 100%) for all LEDs of spot 1 2 0…255 Green intensity (0% to 100%) for all LEDs of spot 1 3 0…255 Blue intensity (0% to 100%) for all LEDs of spot 1 4 0…255 Red intensity (0% to 100%) for all LEDs of spot 2 5 0…255 Green intensity (0% to 100%) for all LEDs of spot 2 6 0…255 Blue intensity (0% to 100%) for all LEDs of spot 2 7 0…255 Red intensity (0% to 100%) for all LEDs of spot 3 8 0…255 Green intensity (0% to 100%) for all LEDs of spot 3 9 0…255 Blue intensity (0% to 100%) for all LEDs of spot 3 10 0…255 Red intensity (0% to 100%) for all LEDs of spot 4 11 0…255 Green intensity (0% to 100%) for all LEDs of spot 4 12 0…255 Blue intensity (0% to 100%) for all LEDs of spot 4

44 70th Stage TRI LED Bundle Complete
LED Lighting Set

7.8 Functions in 15-channel DMX mode

Channel Value Function

1 0…255 Dimmer (0% to 100%)

2 0…10 No function

11…255 Strobe effect, increasing speed

3 0…255 Red intensity (0% to 100%) for all LEDs of spot 1 4 0…255 Green intensity (0% to 100%) for all LEDs of spot 1 5 0…255 Blue intensity (0% to 100%) for all LEDs of spot 1 6 0…255 Red intensity (0% to 100%) for all LEDs of spot 2 7 0…255 Green intensity (0% to 100%) for all LEDs of spot 2 8 0…255 Blue intensity (0% to 100%) for all LEDs of spot 2 9 0…255 Red intensity (0% to 100%) for all LEDs of spot 3 10 0…255 Green intensity (0% to 100%) for all LEDs of spot 3 11 0…255 Blue intensity (0% to 100%) for all LEDs of spot 3 12 0…255 Red intensity (0% to 100%) for all LEDs of spot 4 13 0…255 Green intensity (0% to 100%) for all LEDs of spot 4

Operating

70th Stage TRI LED Bundle Complete
LED Lighting Set 45

Operating

Channel Value Function

14 0…255 Blue intensity (0% to 100%) for all LEDs of spot 4 15 0…39 No function

40…75 Pixel Direction Normal

76…111 Pixel Direction Invert

112…147 Linear

148…183 Square Law

184…219 Inv Square Law

220…255 S-Type

46 70th Stage TRI LED Bundle Complete

LED Lighting Set

7.9 Functions in 19-channel DMX mode

Channel Value Function

1 0…255 Dimmer (0% to 100%) 2 0…10 No function

11…255 Strobe effect, increasing speed

3 0…17 No function

18…34 Red

35…51 R(0)G(255)B(0)

52…68 R(0)G(0)B(255)

69…85 R(255)G(255)B(255)

86…102 R(255)G(150)B(0)

103…119 R(255)G(180)B(0)

120…136 R(255)G(255)B(0)

137…153 R(255)G(0)B(255)

154…170 R(255)G(0)B(140)

171…187 R(0)G(255)B(255)

Operating

70th Stage TRI LED Bundle Complete LED Lighting Set 47

Operating

Channel Value Function

188…204 R(255)G(50)B(205)

205…221 R(200)G(230)B(50)

222…238 R(50)G(255)B(250)

239…255 R(255)G(255)B(75)

4 0…25 No function

26…35 Pre-programmed automatic show no. 02 36…45 Pre-programmed automatic show no. 03 46…55 Pre-programmed automatic show no. 04 56…65 Pre-programmed automatic show no. 05 66…75 Pre-programmed automatic show no. 06 76…85 Pre- programmed automatic show no. 07 86…95 Pre-programmed automatic show no. 08 96…105 Pre-programmed automatic show no. 09 106…115 Pre-programmed automatic show no. 10 116…125 Pre-programmed automatic show no. 11 126…135 Pre- programmed automatic show no. 12

48 70th Stage TRI LED Bundle Complete
LED Lighting Set

Channel Value Function

136…145 Pre-programmed automatic show no. 13 146…155 Pre-programmed automatic show no. 14 156…165 Pre-programmed automatic show no. 15 166…175 Pre- programmed automatic show no. 16 176…185 Pre-programmed automatic show no. 17 186…195 Pre-programmed automatic show no. 18 196…205 Pre-programmed automatic show no. 19 206…215 Pre-programmed automatic show no. 20 216…225 Pre- programmed automatic show no. 21 226…235 Pre-programmed automatic show no. 22 236…245 Pre-programmed automatic show no. 23 246…255 Sound-controlled show

5 0…25 Sound-controlled show no. 01 26…35 Sound-controlled show no. 02

36…45 Sound-controlled show no. 03

46…55 Sound-controlled show no. 04

70th Stage TRI LED Bundle Complete
LED Lighting Set 49

Operating

Channel Value Function

56…65 Sound-controlled show no. 05

66…75 Sound-controlled show no. 06

76…85 Sound-controlled show no. 07

86…95 Sound-controlled show no. 08

96…105 Sound-controlled show no. 09

106…115 Sound-controlled show no. 10

116…125 Sound-controlled show no. 11

126…135 Sound-controlled show no. 12

136…145 Sound-controlled show no. 13

146…155 Sound-controlled show no. 14

156…165 Sound-controlled show no. 15

166…175 Sound-controlled show no. 16

176…185 Sound-controlled show no. 17

186…195 Sound-controlled show no. 18

196…205 Sound-controlled show no. 19

206…215 Sound-controlled show no. 20

50 70th Stage TRI LED Bundle Complete

LED Lighting Set

Channel Value Function

216…225 Sound-controlled show no. 21

226…235 Sound-controlled show no. 22

236…245 Sound-controlled show no. 23

246…255 Sound-controlled show no. 24

6 Function depending on setting of channel 2

Channel 2 = 0…25

No function

Channel 2 = 26…245

0…255 Increasing speed

Channel 2 = 246…255

0…255 Increasing sensitivity

7 0…255 Red intensity (0% to 100%) for all LEDs of spot 1 8 0…255 Green intensity (0% to 100%) for all LEDs of spot 1 9 0…255 Blue intensity (0% to 100%) for all LEDs of spot 1 10 0…255 Red intensity (0% to 100%) for all LEDs of spot 2 11 0…255 Green intensity (0% to 100%) for all LEDs of spot 2

70th Stage TRI LED Bundle Complete
LED Lighting Set 51

Operating

Channel Value Function

12 0…255 Blue intensity (0% to 100%) for all LEDs of spot 2 13 0…255 Red intensity (0% to 100%) for all LEDs of spot 3 14 0…255 Green intensity (0% to 100%) for all LEDs of spot 3 15 0…255 Blue intensity (0% to 100%) for all LEDs of spot 3 16 0…255 Red intensity (0% to 100%) for all LEDs of spot 4 17 0…255 Green intensity (0% to 100%) for all LEDs of spot 4 18 0…255 Blue intensity (0% to 100%) for all LEDs of spot 4 19 0…39 No function

40…75 Pixel Direction Normal

76…111 Pixel Direction Invert

112…147 Linear

148…183 Square Law

184…219 Inv Square Law

220…255 S-Type

52 70th Stage TRI LED Bundle Complete

LED Lighting Set

Operating

7.10 Functions of foot switch

Operating mode ‘Automatic’

Operating mode ‘Sound-con‐ trol’

Operating mode ‘Freeze’ Operating mode ‘Blackout’

Press the foot switch [Auto Run] to start the playback of the preprogrammed automatic shows. Each time you press the switch, the next show will be called up.

Press the foot switch [Sound Active] to start the playback of the sound- controlled automatic shows. Each time you press the switch, the next show will be called up.

Press the foot switch [Freeze] to freeze or unfreeze the show that is currently running.

Press the foot switch [Blackout] for a blackout (all LEDs off). Press it again to return to normal operation.

7.11 Remote control functions

The button functions of the remote control are described in section .

70th Stage TRI LED Bundle Complete

LED Lighting Set 53

Operating

Direct selection of a static colour

Use the numeric keys of the remote control to select a static colour directly. This setting is only relevant if the device is not controlled via DMX.

Value Static colour

0 Cyan

1 Purple

2 Pink

3 Orange

4 Cool white

5 Light red

6 Light green

7 Light blue

8 Yellow

9 Warm white

10 Red

11 Green

54 70th Stage TRI LED Bundle Complete LED Lighting Set

Operating

Value Static colour

12 Blue

13 Amber

7.12 Reset to factory defaults

Proceed as follows to reset the device to factory defaults:

1. Switch off the device.

2. Switch the device on again and hold the buttons [Mode] and [Setup] pressed for about 2 seconds.

70th Stage TRI LED Bundle Complete

LED Lighting Set 55

Technical specifications

8 Technical specifications

Light source 28 × 3in1 LED, 3 W RGB each

Optical properties Beam angle approx. 40° Control DMX, foot switch, infrared remote control (optional) Number of DMX channels 6

Input connections Power supply C14 rubber panel plug DMX control XLR panel socket, 3-pin

Foot switch unit 6.35-mm jack socket

Output connections Power supply 2 × Rubber panel socket C13 DMX control XLR panel socket, 3-pin

Power consumption 90 W

Supply voltage 100 – 240 V 50/60 Hz

Fuse 5 mm × 20 mm, 2 A, 250 V, slow blow

Battery remote control Battery type Lithium-ions button cell CR2025 Voltage 3 V

International Protection Rating IP20

56 70th Stage TRI LED Bundle Complete

LED Lighting Set

Mounting options Stand

Technical specifications

Dimensions W × H × D (spots including T-bar) 1,200 mm × 330 mm × 70 mm Height, max. (T-bar plus stand) 2,400 mm

Weight 16 kg

Ambient conditions Temperature range 0 °C…40 °C

Relative humidity 20%…80% (non-condensing)

Further information

Spotlight included Yes

Effect devices included No

LED bars included No

Controller included Foot switch

Stand included Yes

Case / bag included Yes

Remote control Optionally available (item no. 354223)

70th Stage TRI LED Bundle Complete

LED Lighting Set 57

Plug and connection assignment

9 Plug and connection assignment

Introduction

DMX connections

This chapter will help you select the right cables and plugs to connect your valuable equip‐ ment so that a perfect light experience is guaranteed.

Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or ‘just’ a not working light show!

The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug.

Pin Configuration

1 Ground, shielding

2 Signal inverted (DMX–, ‘cold signal’)

3 Signal (DMX+, ‘hot signal’)

58 70th Stage TRI LED Bundle Complete LED Lighting Set

10 Cleaning Optical lenses

Cleaning

Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device.

■ Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).

■ Always dry the parts carefully.

70th Stage TRI LED Bundle Complete

LED Lighting Set 59

Protecting the environment

11 Protecting the environment

Disposal of the packing material

Environmentally friendly materials have been chosen for the packaging. These materials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of in the proper manner.

Do not dispose of these materials with your normal household waste, but make sure that they mare collected for recycling. Please follow the instructions and markings on the packaging.

Observe the disposal note regarding documentation in France.

Disposal of batteries

Batteries must not be thrown away or burnt, but must instead be disposed of in line with the

local regulations on the disposal of hazardous waste. Use the available collection sites.

Only dispose of lithium batteries when they are empty. Remove lithium batteries from the device before disposal if this is possible without destroying it. Protect used lithium batteries against short circuit, for example by taping the poles. Dispose the built-in lithium batteries together with the device. Check for an appropriate collection facility.

Dispose of the batteries and rechargeable batteries at relevant collection points or through

your local waste facility.

60 70th Stage TRI LED Bundle Complete
LED Lighting Set

Disposal of your old device

Protecting the environment

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) as amended.

Do not dispose of your old device with your normal household waste; instead, deliver it for controlled disposal by an approved waste disposal firm or through your local waste facility. When disposing of the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste management facility. Proper disposal protects the environment as well as the health of your fellow human beings.

Also note that waste avoidance is a valuable contribution to environmental protection. Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal.

You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de.

If your old device contains personal data, delete those data before disposing of it.

70th Stage TRI LED Bundle Complete

LED Lighting Set 61

Notes

62 70th Stage TRI LED Bundle Complete LED Lighting Set

Musikhaus Thomann · Hans-Thomann-S

References

• Buy musical instruments online from the market leader – Thomann United States

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>