tp-link Tapo S505 Smart Wi-Fi Light Switch User Guide

tp-link Tapo S505 Smart Wi-Fi Light Switch

Wire Your Switch

1. Turn off the circuit breaker. Check whether your power is off by turning your switch on and off a few times.
   CAUTION !

2. Risk of Electric Shock – The product should be installed by a qualified electrician.

3. High Voltage – Disconnect power supply at the circuit breaker before servicing.

4. Use copper conductors only.

5. Remove the wallplate of the old switch and label the wires.

   • Ground : Usually green or copper.
   • Neutral : Usually white, not connected to the dumb switch.
   • Line / Load : Usually black, and connected to the dumb switch.
   • Note : If you are unsure, consult a qualified electrician.

6. Disconnect wires from the old switch

7. Connect the wires to the smart switch as shown below.

8. Line up the switch with the mounting holes. Secure it with screws.

9. Attach the wallplate and turn on the circuit breaker. Then the wiring is finished.

Set Up Your Switch

Step 1: DOWNLOAD APP
Get the Tapo app from the App Store or Google Play.

Step 2: SET UP
Tap the button in the app. Select Switches and then your model. Follow the step-by-step app instructions to set up your smart switch.

Third-Party Services
Tapo works with Alexa, Google Assistant, and other third-party services to control your switch by voice. Go to Me > Third-Party Services in the Tapo app to integrate third-party services.

For step-by-step setup instructions, please visit:

• Google Home Assistant:
  https://www.tp-link.com/support/faq/2779/

• Amazon Alexa:
  https://www.tp-link.com/support/faq/2780/

Specifications

• Rating: 100-120 V~ 50/60 Hz
• Load: 15 A General Use, 600 W Incandescent, 1/6 HP Motor
• Operation temperature: 0~40 ℃
• Method of mounting included: Independently mounted (Vertically position only);
• Operating control, Type 1.C action
• Pollution Degree 2, Rated Impulse Voltage 2500 V
• Software Class A, NEMA Type 1

Appearance

Button Explanations

Reset

| Press and hold for about 5s to reset Wi-Fi while keeping other settings.

Press and hold for about 10s to restore your switch to factory default settings.

---|---
Restart|

LED Status

Matter Setup Code
Detach the wallplate with force, and you’ll see the Matter numeric code. Your can find another Matter setup code label in the package and stick it anywhere you like as needed for initial matter setup.

CAUTION : High Voltage-Disconnect power supply at the circuit breaker before servicing.

Safety Notice
Before installing, servicing or removing the switch, read and follow all safety precautions including the following:

• CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a
  non-contact voltage tester to ensure the power is off.

• The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician.

• Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.

• Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm)

Support
For technical support, the user guide and other information, visit https://www.tapo.com/support.

References

• How to Link a Tapo or Kasa Account to Amazon Alexa | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>