ZOELLER 75 Sump Pump Owner’s Manual
- August 2, 2024
- Zoeller
Table of Contents
ZOELLER 75 Sump Pump
Specifications
- Model: 75
- Product: Sump Pump
- Features: Epoxy paint, 1-1/2 NPT discharge size, solids handling, auto on/off points
- Motor: Horse Power, Voltage, Phase, Hertz, RPM, Insulation, Amps
- Materials: Motor housing, pump housing, base, upper bearing, lower bearing, mechanical seals, impeller type
- Certification: Certified to CSA Standard 227875
- Total Dynamic Head: 12-3/8 inches (314 mm)
Product Usage Instructions
Installation
- Ensure all installation of controls, protection devices, and wiring is done by a qualified licensed electrician.
- Follow all electrical and safety codes including the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
- Place the sump pump in the desired location ensuring it is level and stable.
- Connect the discharge pipe to the pump’s outlet using appropriate fittings.
- Ensure the float switch is properly adjusted for the desired on/off points.
Operation
- Plug the sump pump into a grounded electrical outlet.
- Ensure the pump is submerged in water to prevent overheating.
- Monitor the pump’s operation and check for any unusual noises or vibrations.
- If the pump has an automatic mode, set the desired on/off points according to your needs.
Maintenance
- Regularly inspect the pump for any signs of damage or wear.
- Clean the pump and remove any debris that may obstruct its operation.
- Check and lubricate bearings as recommended by the manufacturer.
- Test the pump periodically to ensure it functions properly.
FAQ
- Q: How often should I test my sump pump?
- A: It is recommended to test your sump pump at least once every three months to ensure it is working correctly.
- Q: Can this sump pump handle solid waste?
- A: Yes, this sump pump is designed to handle solids as specified in the product features.
Features
- Energy saving product
- 2-year warranty
- Reliable integrated vertical switch
- 1/2 HP 115 V sump pump
- Performance up to 25′ (7.6 m) TDH
- Flows up to 50 GPM (189 LPM)
- Rugged cast iron motor housing
- Engineered plastic base
- Corrosion-resistant, powder-coated epoxy paint
| MOTOR | Horse Power | 1/2 |
|---|---|---|
| Voltage | 115 | |
| Phase | 1 Ph | |
| Hertz | 60 Hz | |
| RPM | 3450 | |
| Type | Permanent split capacitor | |
| Insulation | Class B | |
| Amps | 5.6 | |
| PUMP | Operation | Automatic |
| Auto On/Off Points | 8-1/4″ (21 cm) / 2-1/2” (7 cm) | |
| Discharge Size | 1-1/2″ NPT | |
| Solids Handling | 3/8″ (9 mm) spherical solids | |
| Cord Length | 10′ (3 m) standard | |
| Cord Type | UL listed, 3-wire, grounded plug | |
| Max. Head | 25’ (7.6-m) | |
| Max. Flow Rate | 50 GPM (189 LPM) | |
| Max. Operating Temp. | 104 °F (40 °C) | |
| Cooling | Oil filled | |
| Motor Protection | Auto reset thermal overload | |
| MATERIALS | Motor Housing | Cast iron |
| Pump Housing | Engineered plastic | |
| Base | Engineered plastic | |
| Upper Bearing | Ball bearing | |
| Lower Bearing | Ball bearing | |
| Mechanical Seals | Carbon and ceramic | |
| Impeller Type | Non-clogging vortex | |
| Impeller | Engineered plastic | |
| Hardware | Stainless steel | |
| Motor Shaft | SUS420J2 stainless steel | |
| Gasket | NBR |
Dimension
CAUTION: All installation of controls, protection devices, and wiring
should be done by a qualified licensed electrician. All electrical and safety
codes
CAUTION should be followed including the most recent National Electrical
Code (NEC) and the Occupational Safety and Health Act (OSHA).
© Copyright 2024 Zoeller® Co. All rights reserved. zoellerpumps.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>