Shenzhen Chileaf Electronics CDN200 Cadence and Speed Sensor User Manual

Cadence and Speed Sensor
User Manual
Model: CDN200

Thank you for selecting this Cadence and Speed Sensor! CDN200 can track and monitor your cadence and speed on APP.

Packaging contents

Mode select

1. Cadence mode: the Blue LED is on to indicate the unit is on cadencemode when powered up.
2. Speed mode: the RED LED is on to indicate the unit is in speed mode when powering up.
3. To switch cadence and speed mode, just need to reinstall the battery.
   How to install the cadence and speed sensor on your bike
   It’s recommended you secure your bike on a stand while installing the sensor.

Installing the cadence sensor

1. Place and hold the crank rubber pad on the inside of the non-drive side crank arm, then place the cadence sensor.
2. Tied the cadence sensor and crank arm with the silicone ring
3. Rotate the crank arm to check for clearance. Take a few-minute test ride and inspect the sensor to ensure there is no interference.

Installing the speed sensor

1. Place and hold the wheel rubber pad and speed sensor on top of the wheel hub
2. Tied the sensor and hub with the silicone ring
3. Rotate the wheel to check for clearance. The sensor should not contact other parts of your bike.

How to track and monitor your data

1. The first time you choose you to prefer an APP to install on your smartphones such as Polar beat, Wahoo Fitness, Endomondo Runtastic PRO, or Zwift. X-fitness etc.
   

2. Then you connect the sensor to your device using Bluetooth® technology, it needs a pair when you start.

How to replace the battery
The device uses one CR2032 battery. APP will remind that a low battery level needs replacement.

1. Twist the cover counterclockwise until the cover is loose enough to remove.

2.  Remove the cover and the battery.

3. Insert the new battery into the cover, observing polarity.
   Caution”Do not ingest battery, Chemical Burn Hazard”
   NOTE: Do not damage or lose the O-ring gasket.

4. Twist the cover clockwise so that the marker on the cover aligns with the marker on the case.

5. NOTE: The LED flashes Blue to indicate that is cadence mode, RED is for Speed mode.

Specification

Troubleshooting

If your device will not connect to the speed and cadence sensors, you can try to Rotate the crank arm or wheel two revolutions to wake up the sensor. Or check the battery level via APP and replacement

• need reinstall the battery if no LED flash when replacing the battery.

EU-DECLARATION OF CONFORMITY
Hereby, declares that Cadence and Speed Sensor (model: CDN200) is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU. A copy of the signed and dated Declaration of Conformity is available

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>