INSTALLATION INSTRUCTIONS
CSX1 Series
LED Commercial Strip Premium

OVERVIEW

WHAT’S IN THE BOX

• CSX1 Fixture
• Junction cover plates (x2)
• Surface mounting hardware
•  Spare; wire nuts & fixture screws

WHAT YOU’LL NEED

• Wiring supplies as per national and local electrical codes

• 2 Phillips screwdriver

• Safety glasses

ACCESSORIES

• Aircraft Cable kit
• Linear Alignment Kit
• V-hook and chain kit

IMPORTANT
Before installing fixture, read all instructions and retain for future reference. The important instructions and safeguards that appear in this document are not inclusive of all possible conditions and situations that may occur. It must be understood that common sense, caution, and care are factors that cannot be built into a product. These factors must be supplied by those that care for and operate the fixture.
For additional information not covered in this document please contact a local representative.
WARNING AND SAFETY

• Risk of electric shock!
• Ensure power is OFF at the electrical panel before starting installation or maintenance
• Verify site supply voltage matches luminaire product label
• Ensure the cover is closed during operation
• Modifications to the product will void warranty
• Ambient temperature range under normal operation not to exceed 20°C to 45°C (-4°F to 113°F)
• Wiring to fixture must be in accordance with the National Electrical Code and all applicable local electrical and safety regulations
• Minimum 90° supply conductors

INSTALLATION

SURFACE MOUNT

1. With a #2 Phillips screwdriver, remove and retain the four safety screws and squeeze the area between the narrow slot and the indent holding the lens to release the lens from the housing and open the fixture.

2. With fixture held in position, use the fixture as a template to mark the mounting hole positions on each end.
   Spacing for mounting holes;
   4ft: 36-1/4” (920 mm)
   8ft: 83-3/8” (2118 mm)

3. As needed, slide on to secure junction cover plates to back of fixture.

4. Connect fixture to power as per included wiring diagrams.

5. Secure the fixture to the surface with appropriate mounting hardwar

6. Close the fixture by pressing lens into housing and securing with retained screws from step 1

7. Turn power on, and test luminaire.

CHAIN MOUNT

1. Hook each v-hook onto the corresponding slots at each end of the fixture.
2. Install chain on each v-hook.
3. Secure the chain to the ceiling where the fixture will be suspended.
4. With a #2 Phillips screwdriver, remove and retain the four safety screws and squeeze the area between the narrow slot and the indent holding the lens to release the lens from the housing and open the fixture.
5. Connect to power as per included wiring diagrams.
6. Close the fixture by pressing lens into housing and securing with retained screws from step 4
7. Turn power on, and test luminaire.

INSTALLATION FOR OPTIONAL ACCESSORIES (sold separately)
AIRCRAFT CABLE KIT

1. Anchor top of aircraft cables to the building structure.
2. Open the fixture by squeezing or pushing in the buttons located on either end. Lens is held with safety cable.
3. Attach aircraft cables with provided M5 square screw. Adjust cable height as desired.
4. Connect to power as per included wiring diagrams.
5. Close the fixture. Squeeze or push in the side buttons and press lens into housing. Turn power on, and test luminaire.
6. Turn power on, and test luminaire.

LINEAR ALIGNMENT KIT, SURFACE INSTALL

1. With a #2 Phillips screwdriver, remove and retain the four safety screws and squeeze the area between the narrow slot and the indent holding the lens to release the lens from the housing and open the fixture.
2. With fixture held in position, use the fixture as a template to mark the mounting hole positions on each end.
3. As needed, slide on to secure junction cover plates to back of fixture
4. Remove desired end knockouts.
5. Secure the linear alignment plate to the end of one fixture.
6. Connect fixture to power as per included wiring diagrams.
7. Secure the fixture to the surface with appropriate mounting hardware.
8. Close the fixture by pressing lens into housing and securing with retained screws from step 1.
9. Repeat steps 1-8 as needed.
10. Turn power on, and test luminaire.

COMBINATION LINEAR ALIGNMENT KIT, AIRCRAFT CABLE KIT INSTALL

1. Anchor top of aircraft cables to the building structure.
2. Open the fixture by squeezing or pushing in the buttons located on either end. Lens is held with safety cable.
3. Attach aircraft cables with provided M5 square screw.
4. Remove desired end knockouts.
5. Secure the linear alignment plate to the end of one fixture.
6. Connect fixture to power as per included wiring diagrams.
7. Close the fixture. Squeeze or push in the side buttons and press lens into housing.
8. Repeat steps 1-7 as needed. Secure linear alignment plate to the adjacent fixture with provided screws.
9. Turn power on, and test luminaire.

WIRING SCHEMATIC

Note: refer to the wiring diagram included with the emergency battery if added to the fixture.
WIRE GUARDS Attach wire guard to fixture with #2 Phillips screwdriver and provided screws.

©2023 EiKO Global, LLC. World Headquarters: 18000 W. 105th Street, 3 Floor, Olathe, KS 66061 1.800.852.2217
Head Office, Canada: 7900 Goreway Drive, Unit 8, Brampton, ON L6T 5W6 1.888.741.2673
eiko.com
Rev. 02/21/23

References

• Torshare _Outdoor LightingIndoor Lighting Industrial Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>