Enping Tianheng Electroacoustic Equipment Factory Professional Karaoke Wireless Microphone Equipment User Manual

Enping Tianheng Electroacoustic Equipment Factory Professional Karaoke

Wireless Microphone Equipment

Foreword

We are very grateful to you for purchasing this product. Please read this manual carefully to understand how to operate the model you purchased. After you have read this manual, please keep it in a safe place for future reference. This wireless microphone,which uses the United States efficient low-RF emission technology .ultra-high sensitivity UHF narrowband high-frequency receiver, the use of frequency synthesis technology, to multi-band switching, .with independent development of dynamic audio compression, expansion circuit.mirror Frequency suppression circuit,, multiple detection squelch circuit,switch impact elimination circuit, anti-transmission circuit, slow output control and other technology, and access to computer EDA, analog online auxiliary design, strict product quality control, so that each system has excellet Performance.
Bring happiness to home –

Receiver Front Fcnction Dicgram

Receiver Beck Feectioe Dicgram

Micropkoee Feectioe Dicgram

Features:

1.  Super noise reduction function, high signal to noise ratio.
2.  Strong anti-interference, high-performance printed noise output.
3. Wide corresponding frequency range, low distortion.
4. Hand-held switch without impact, to ensure that after the power amplifier system and speaker safety.
5. Improve the working status instructions and power instructions.
6. Practical distance.the ideal environment to reach more than 50 meters,complex environment with a radius of 30 feet.
7. Dual-channel design allows simultaneous use of two hand-held microphones without disturbing each other.
8. The use of frequency synthesis technology can be more widely applied to a wider range of switching.
9. For network karaoke, television singing, karaoke hall, home entertainment and many other occasions.

Bluetooth Connection and Use Method:

1. Turn on Bluetooth of play source device, and search for device
2. Search for the microphone host device Bluetooth
3. Play source device pairing to connect the microphone receive.It’s done.

Note: The wiring used for the connection may depend on the specifics of the source device and the audio jack.

Karaoke Connection Diagram

  TV connection using method:

1. Connect the supplied audio cable from the headphone jack, AV output port, audio output port, and audio output port on the TV to the INPUT jacks on the microphone unit.
2.  Connect the audio input from the OUTPUT jack of the receiver with the audio cable.
3. Connect the receiver to power, install AA battery into microphone, then it is readybe used.

Note: When the TVoutputjacks are red and white jacks, please connect the INPUT jacks of the host device with RCA to RCA cable When the audio inputjack is 3.SMM, please use RCA-3.5 MM cable to connect to the sound.

Computer Karaoke Connection Diagram

Computer Connection and Use Method:
l.Connect the OUTPUT audio output port of the receiver device to the computer microphone hole with the included audio cable.
2. Audio connected to the computer’s headphone jack.
3. Connect the receiver to power, install battery into microphone, then it is ready be used.

Note : There is no sound after connecting the computer , the microphone volume in the system sound device is on, and the sound of the microphone option in the speaker in the sound device is on. The above is for reference only , the specific settings , please contact the dealer or online customer service staff.

Cell Phone Karaoke Connection Diagram

How to Connect and Use with Cell Phone:

1. Use the provided RCA-3.Smm cable from the phone’s headset jack to connect to the INPUT jack on the receiver.
2. Connect the audio input jack from the OUTPUT jack of the receiver again using the audio cable.
3. Connect the receiver to power, install AA battery into microphone, then it is ready be used.

Set-top Box Karaoke Connection Diagram

Set-top Box Connection and Use Method:

1. Connect the supplied audio cable from the set-top box’s output jack to the receiver’s INPUT jack.
2. Connect the audio input jacks from the output jacks of the receiver again using the audio cable.
3. Connect the receiver to power, install AA battery into microphone, then it is ready be used.

Note: When the set-top box output hole is red and white RCA output, connect to the INPUT output jack of the receiver with RCA to RCAaudio cable. When the audio input jack for a hole connect it withe RCA to 3.5mm audio cable with receiver.

Power Amplifier Connection Diagram

1. Connect the supplied 1-to-1 audio cable from the amplifier’s microphone jack to the Tin put R + L hole of the receiver.
2. Connect the receiver to power, installAA battery into microphone, then it is ready be used.

Use Connection Guide

1. Place the (receiver) near the desktop or multimedia speakers, plug in the power cord, plug one end of the supplied audio cable into the unit’s OUTPUT connector and connect the other end to a desktop microphone Input (MIC IN) or multimedia speaker audio input. The(receiver) two antenna adjustment and vertical ground, turn on (receiver) power switch.
   The power light is on.The machine is in standby working condition. (* The receiver is best not to work in dead ends to ensure a good signal environment).

2.  Open the handpiece battery cover, insert the battery into the battery holder correctly, and close the battery compartment.(*Battery and battery clip all electrode label, pay attention tothe battery do not install anti)

3. Press the microphone switch for 2 seconds and the hand-held display will illuminate. Atthis time, the (receiver) and its corresponding signal indicator are bright it, indicating thatthe (receiver) has received a valid signal of the microphone,and signal volume knob and the subsequent volume knob of the signal amplifier are properly adjusted so that the system has Appropriate volume, speak to the microphone at this time there is voice.

4. Receiver designed RCA output jack, for different broadcast, recording equipment and occasions.

TECHNICAL INDEX SPECIFICATIONS

RECIEVER
Receiving frequency: UHF 516.3-595.5MHz Sensitivity: 2/MV
lmage interference ratio: >88DB
Audio output: 800MV-1.4V
Receive channel: 2 Road
Power consumption: 3W

HANDHELD TRANSMITTER
Carrier frequency: UHF 516.3-595.5MHz Transmit power: 10MW
Harmonic: <Main wave 40DB
Pickup: 600Ω single finger
Antenna: built-in

SAFTEY GUIDE

After-sale Service and Instructions

Dear users, in order to effectively protect your rights and interests, a clear dealer agents and companies should bear the responsibility of products and behavior! Please read the following:

1. Warranty Card is the necessary proof of warranty for the product free service;
2. Installation of the principle of three bags of sales responsibility. product problems such as problems with the “product warranty card”contact with the dealer,the dealer to provide services to customers, our company to provide services to dealers;
3. The company promises: from the date of sale (date to customer receipt) quality problems within 7 days, the customer can choose to return, replacement. From the date of sale within 7-15 days of quality problems can choose to replace or repair; from the date of sale within 1 year of quality problems, customers can repair free of charge; fromthedate of sale within three years of quality problems can be repaired (after-saies Service points only charge the cost of components and materials); Please ask the customer to fill out the “product warranty card” with the dealer

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by  the party responsible for compliance could void the user’s authority to operate the equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>