CIC36RP2VS1 Integrated Bottom Freezer Refrigerator

Product Information

Specifications

• Product Type: Integrated Bottom-Freezer Refrigerator

• Installation Type: Single Integrated, Dual Standard, Dual
  Integrated (Single Door Models Only)

• Manufacturer: Cafe Appliances

• Model Number: 31-1000731

Product Usage Instructions

Single Integrated Installation

1. Step 1: Remove Packaging

2. Step 2: Install Water Line

3. Step 3: Install Anti-tip Brackets

4. Step 4: Connecting Water Supply

5. Step 5: Inserting/Securing into Cabinet
   Surround

6. Step 6: Level Unit

7. Step 7: Final External Unit Preparation

8. Step 8: Handle Installation

9. Step 9: Toe Kick Installation

10. Step 10: Internal Unit Preparation

11. Step 11: Start Icemaker

Dual Standard Installation (Single Door Models Only)

Dual Integrated Installation (Single Door Models Only)

Frequently Asked Questions (FAQ)

Q: What should I do if I receive a damaged unit?

A: If you received a damaged unit, immediately contact your
dealer or builder for assistance.

Q: How should I handle electrical connections for the

refrigerator?

A: Always plug the refrigerator into a grounded 3-prong outlet
and avoid using adapters or extension cords. Follow the grounding
instructions provided in the manual to prevent electrical
hazards.

TM

Installation Instructions

Integrated Bottom-Freezer Refrigerators

Safety Design Guide
Dimensions and Clearances Accessories/Kits
Instructions for Single Standard Installation The Installation Space Tools, Hardware, Materials Grounding the Unit Flooring Step 1. Remove Packaging Step 2. Install Water Line Step 3. Install Anti-tip Brackets Step 4. Change Power Cord Step 5. Case Trim Installation Step 6. Connecting Water Supply Step 7. Inserting/Securing into Cabinet Surround Step 8. Level Unit Step 9. Final External Unit Preparation Step 10. Handle Installation Step 11. Toe Kick Installation Step 12. Internal Unit Preparation Step 13. Start Icemaker
Instructions for Single Integrated Installation The Installation Space Tools, Hardware, Materials Grounding the Unit Flooring Step 1. Remove Packaging Step 2. Install Water Line Step 3. Install Anti-tip Brackets Step 4. Connecting Water Supply Step 5. Inserting/Securing into Cabinet Surround Step 6. Level Unit Step 7. Final External Unit Preparation Step 8. Handle Installation Step 9. Toe Kick Installation Step 10. Internal Unit Preparation Step 11. Start Icemaker
Instructions for Dual Standard Installation (Single Door Models Only)
The Installation Space
Questions? Visit cafeappliances.com.

2

Tools, Hardware, Materials

31

Grounding the Unit

31

5

Flooring

31

6

Step 1. Remove Packaging

32

Step 2. Install Water Line

33

7 8 9 9 9 10 10 11 12 12 13 14 15

Step 3. Preparing Unit for Installation – Dual Install Step 4. Install Anti- tip Brackets Step 5. Joining Dual Installed Units Step 6. Change Power Cord Step 7. Case Trim Installation Step 8. Connecting Water Supply Step 9. Inserting/Securing into Cabinet Surround Step 10. Level Unit Step 11. Final External Unit Preparation Step 12. Handle Installation Step 13. Toe Kick Installation Step 14. Internal Unit Preparation Step 15. Start Icemaker

34 35 36 37 37 38 39 41 41 43 43 43 43

15 Instructions for Dual Integrated Installation

16

(Single Door Models Only)

44

16 16 17

The Installation Space Tools, Hardware, Materials Grounding the Unit

45 46 47

18

Flooring

47

19 20 20 20 21 22 23 24 25 26 26 27 27

Step 1. Remove Packaging Step 2. Install Water Line Step 3. Preparing Unit for Installation Step 4. Install Anti-tip Brackets Step 5. Joining Dual Installed Units Step 6. Connecting Water Supply Step 7. Inserting/Securing into Cabinet Surround Step 8. Level Unit Step 9. Final External Unit Preparation Step 10. Handle Installation Step 11. Toe Kick Installation Step 12. Internal Unit Preparation Step 13. Start Icemaker

47 48 49 50 51 52 53 54 55 56 56 57 57

27 28

Door Panel Adjustments and Trim Installation Hardware Supplied

58 59

Panel Adjustment Bracket Locations

59

29 30

Side to Side Adjustment Height and Depth Adjustment Trim Installation

60 60 60

English/Français/Español

31-1000731 Rev. 3 04-24

Safety Information

BEFORE YOU BEGIN
Read these instructions completely and carefully.
· IMPORTANT ­ Save these instructions for local inspector’s use. Observe all governing codes and ordinances.
· Note to Installer ­ Be sure to leave these
instructions with the Consumer.
· Note to Consumer ­ Keep these instructions with
your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately contact your dealer or builder.
Skill Level ­ Installation of this unit requires basic
mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Café Warranty. See the Owner’s Manual for warranty information.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord. If the supply cord is damaged it must be replaced by a qualified service professional with an authorized service part from the manufacturer.

Do not use an extension cord with this appliance.
Failure to follow these instructions can result in death, fire, or electrical shock.
Follow the instructions in the section Grounding the unit.
This appliance must be installed with a means in the fixed house wiring or circuit breaker for disconnecting the appliance from the electrical supply after installation.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward

which could result in death or serious injury. Read and follow the entire installation instructions for securing the appli-

ance with the anti-tip system.

WARNING

Fire or Explosion Hazard.

Keep flammable materials and vapors away from appliance. Failure to do so can result in fire, explosion,

or death.

WARNING To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
CAUTION Lifting Hazard
This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance, 3 people are required for proper installation.

CAUTION Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.
PROPER DISPOSAL OF YOUR APPLIANCE
Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local authorities for the environmentally safe disposal or recycling of your appliance. Consider recycling options for your appliance packaging material.

2

31-1000731 Rev. 3

Consignes de sécurité

AVANT DE COMMENCER
Veuillez lire toutes ces instructions attentivement.
· IMPORTANT ­ Conservez ces instructions à l’usage de l’inspecteur local. Observez tous les codes et décrets en vigueur.
· Note à l’installateur ­ Assurez-vous de laisser ces
instructions au consommateur.
· Note au consommateur – Conservez ces instructions avec votre manuel d’utilisation pour consultation ultérieure.
Si vous avez reçu un appareil endommagé, veuillez communiquer immédiatement avec votre revendeur ou votre
entrepreneur.

Niveau de compétence ­ L’installation de cet appareil
exige des compétences de base en mécanique, menuiserie et plomberie. La responsabilité d’une installation adéquate relève de l’installateur. La garantie Café ne couvre pas les défectuosités du produit causées par une installation inadéquate. Consultez le manuel d’utilisation pour des renseignements sur la garantie.

AVERTISSEMENT

Risque d’électrocution.

Branchez l’appareil dans une prise à 3 broches mise à la terre.

N’enlevez pas la broche de mise à la terre.

N’utilisez pas un adaptateur.

Cessez immédiatement l’utilisation d’un cordon électrique endommagé. Si le cordon électrique est endommagé, son remplacement doit être exécuté par un technicien en réparation qualifié au moyen d’un cordon de rechange autorisé par le fabricant.

N’utilisez pas un cordon de rallonge avec cet électroménager.
Le non-respect de ces instructions peut occasionner un décès, un incendie ou un choc électrique
Suivez les instructions de la section Mise à la terre de l’appareil.
Le circuit électrique auquel cet électroménager sera raccordé doit comporter un disjoncteur ou un autre dispositif permettant de couper l’alimentation électrique à l’appareil après l’installation.

AVERTISSEMENT

Risque de basculement.

Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour prévenir

un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des instruc-

tions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.

AVERTISSEMENT

Risque d’incendie ou d’explosion.

Gardez les matières et les vapeurs inflammables à distance de l’électroménager. L’omission de prendre cette précaution peut

entraîner un incendie, une explosion ou la mort.

AVERTISSEMENT Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces à la portée des enfants âgés de moins de 3 ans.

AVERTISSEMENT Risque lié à la manipulation d’un objet lourd
Cet appareil est très lourd. Afin de réduire le risque de blessure pendant la manipulation et l’installation de cet électroménager, la
participation de 3 personnes est nécessaire à l’exécution d’une installation correcte.

AVERTISSEMENT Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les portes et l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.
MISE AU REBUT ADÉQUATE DE VOTRE ÉLECTROMÉNAGER
Veuillez jeter ou recycler votre électroménager conformément aux règlements fédéraux ou locaux. Communiquez avec les instances locales pour en savoir plus sur la mise au rebut ou le recyclage de votre électroménager. &RQVLGpUH]OHVRSWLRQVGHUHFFODJHGHVPDWpULDX[G¶HPEDOODJHGHYRWUHpOHFWURPpQDJHU

31-1000731 Rev. 3

3

Información sobre Seguridad

ANTES DE COMENZAR

Lea estas instrucciones en su totalidad y atentamente.

IMPORTANTE ·

­ Conserve estas instrucciones

para uso del inspector local. Cumpla con todos los códigos y

ordenanzas gubernamentales.

· Nota para el Instalador ­ Asegúrese de que el

Comprador conserve estas instrucciones.

· Nota para el Consumidor ­ Guarde estas

instrucciones con su Manual del Propietario para referencia

futura.

Si la unidad que recibió está dañada, se deberá comunicar de
inmediato con su vendedor o fabricante.
Nivel de habilidad ­ La instalación de esta unidad
requiere un nivel básico de habilidades mecánicas, de carpintería y plomería. La correcta instalación del producto es responsabilidad del instalador. Si se producen fallas en el producto debido a una instalación inadecuada, la Garantía de Café no cubrirá las mismas. Para obtener información sobre la garantía, consulte el Manual del Propietario.

ADVERTENCIA

Riesgo de Descarga Eléctrica

Enchufe en un tomacorriente con conexión a tierra de 3

No use un prolongador con este electrodoméstico. Si no se

cables.

siguen estas instrucciones, se podrá producir la muerte, incen-

No elimine el cable de conexión a tierra.

dios o descargas eléctricas.

No use un adaptador.
Inmediatamente interrumpa el uso de un cable de suministro de corriente dañado. Si el cable de corriente se encuentra dañado, su reemplazo deberá ser realizado por un profesional calificado del servicio técnico, utilizando una pieza del servicio técnico autorizada por el fabricante.

Siga las instrucciones que figuran en la sección de Conexión de tierra de la unidad.
Este electrodoméstico deberá ser instalado por algún medio en el cableado fijo del hogar o en un disyuntor para desconectar el electrodoméstico del suministro eléctrico luego de la instalación.

ADVERTENCIA

Riesgo de Caídas

Estos electrodomésticos son inestables, especialmente cuando una puerta se encuentre abierta, y deben estar asegurados a fin

de evitar caídas hacia adelante que podrían resultar en la muerte o en lesiones graves. Lea y siga las instrucciones de instalación

en su totalidad para asegurar el electrodoméstico con el sistema anti volcaduras.

ADVERTENCIA

Riesgo de Incendio o Explosión.

Mantenga cualquier material y vapores inflamables alejados del electrodoméstico. Si no se cumple con esto, se podrá producir

una explosión, incendio o la muerte.

ADVERTENCIA A fin de reducir el riesgo asociado con descargas, no permita que los niños menores de 3 años de edad
tengan acceso a las partes pequeñas durante la instalación de este producto.

PRECAUCIÓN Riesgo al levantar la puerta
Esta unidad es muy pesada. A fin de reducir el riesgo de lesión de una persona al maniobrar e instalar este electrodoméstico, se
requiere contar con 3 personas para una correcta instalación.

PRECAUCIÓN Mantenga los dedos fuera de los espacios de “riesgo de lastimaduras”; los espacios entre las puertas
y entre las puertas y el gabinete son necesariamente pequeños. Tenga la precaución de cerrar las puertas cuando los niños se encuentren en el área.
FORMA ADECUADA DE DESCARTAR SU ELECTRODOMÉSTICO
Descarte o recicle su electrodoméstico de acuerdo con las Regulaciones Federales y Locales. Comuníquese con las autoridades locales para descartar o reciclar su electrodoméstico de forma ambientalmente segura. Tenga en cuenta las opciones de reciclaje del material de embalaje de su electrodoméstico.

4

31-1000731 Rev. 3

Design Guide

DIMENSIONS AND CLEARANCES
Dimensions in parentheses are in centimeters.
Overall Dimensions (with 3/4″ door panels installed)
Single Door Models

35 3/4″ (90.8)

61 11/16″ (156.7)
24 3/4″ (62.9) 23 7/8″ (60.6) 22 1/8″ (56.2)

French Door Models
43 3/4″ (111.1)

35 3/4″ (90.8)

24 3/4″ (62.9) 23 7/8″ (60.6) 22 1/8″ (56.2)

83 7/8″
(213)

21 11/16″*
(55.1)

83 11/16″
(212.6)

83 7/8″
(213)

21 11/16″*
(55.1)

83 11/16″
(212.6)

FRONT VIEW 35 5/16″ (89.7) *

18 7/16″*
(46.8)
4″
(10.2)
SIDE VIEW

FRONT VIEW

• Depth dimension without handle. Handle adds 2 9/16″ depth.

18 7/16″
(46.8)
4″
(10.2)
SIDE VIEW
35 5/16″ (89.7)

**Dim A

TOP VIEW

**Dim A

TOP VIEW

39 9/16″
(100.5)

Door Angle
90° 115°

Dim A

Door

Handle

2 3/16″ (5.6)

6 3/4″ (17.1)

17 11/16″ (44.9) 21 9/16″ (54.8)

(11.6) min
*Case width at widest part. **Dim A = Clearance needed to wall or adjacent appliance. Dimensions based on
handle height of 2 9/16″ (6.5) and a hand clearance of 2″ (5.1)
Shipping height Use leveling legs and wheels to adjust the height up to 84″ (213.36 cm). Maximum adjustment is 1″ (2.54 cm).

21 5/8″
(54.9)

Door Angle
90° 115°

Dim A

Door
2 3/16″ (5.6) 10 1/8″ (25.7)

Handle
6 3/4″ (17.1) 14″ (35.6)

*Case width at widest part. ** Dim A = Clearance needed to wall or adjacent appliance. Dimensions based on
handle height of 2 9/16″ (6.5) and a hand clearance of 2″ (5.1)

Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Refer to Dim A above for clearances for door swing.

31-1000731 Rev. 3

5

Design Guide
7KH&DIp,QWHJUDWHG%RWWRP)UHH]HU5HIULJHUDWRUVFDQEHLQVWDOOHGLQPDQFRQ¿JXUDWLRQVZLWKGLHUHQWLQVWDOODWLRQ situations.
Instructions for Integrated Installation – Dual and Single New construction installation with 25″ deep openings
Instructions for Standard Installation – Dual and Single Existing construction installation (existing cutouts) with 24″ deep openings that are 35-1/2″ wide or dual installations 71-1/2″ wide.

ACCESSORIES/KITS
Z KMV+HDWHU8QL¿FDWLRQ.LW WX08X10006 Water Line 8′ (2.5 m) ZKW36V Single Install Standard Installation Kit ZKW72V Dual Install Standard Installation Kit 6WDLQOHVV6WHHO7RH.LFNVIRU’XDO,QVWDOO
72″ ZKK72R (Standard Installation) 72″ ZKN72V (Integrated Installation)

)UHQFK’RRU+DQGOH.LWV CXSB4H4PVBZ Bronze 4 Handle Kit CXSB4H4PVCU Copper 4 Handle Kit CXSB4H4PVBT Black 4 Handle Kit CXSB4H4PVCG Brass 4 Handle Kit CXSB4H4PVFB Flat Black 4 Handle Kit

6LQJOH’RRU+DQGOH.LWV

CXSB3H3PVBZ CXSB3H3PVCU CXSB3H3PVBT CXSB3H3PVCG CXSB3H3PVFB

Bronze 3 Handle Kit Copper 3 Handle Kit Black 3 Handle Kit Brass 3 Handle Kit Flat Black 3 Handle Kit

6

31-1000731 Rev. 3

Instructions for Single Standard Installation
Existing construction installation with 24″ deep openings that are 35-1/2″ wide

31-1000731 Rev. 3

7

Design Guide – Single Standard Installation

SINGLE STANDARD INSTALLATION SPACE

Dimensions in parentheses are in centimeters.

24″ (61)

B 1-1/2″ Landing / Finished Spacer

35-1/2″ (90.2)

6″ (15.2)

Finished Return on both sides
and top

B
Cabinet
Hinge

A ¾” Landing/Finished Space
A
Cabinet Handle

83 1/2″ min. 84 1/2″ max. (212.1 ­ 214.6) *Trim will overlap additional 3/4″

18″ (45.7)

9″ (22.9)

8″ 9″ (20.3) (22.9)
ELECTRIC WATER

6″ (15.2)

2 1/2″ (6.4)
For 24″ Deep Cutouts A trim kit (ZKW36V) is required for standard installations.

Water And Electrical Locations The recommended electrical location is shown in the diagram. If the electrical location is higher than shown, use the longer power cord provided in trim kit (ZKW36V). Follow instructions in step 4 to change power cord.

Water supply must be located as shown.

Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Refer to Dim A on page 5 for clearances needed for door swing.
Additional Specifications · A separate 115 volt 60Hz., 15 or 20 amp power supply
is recommended for each product. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
· Water line must be located on the back wall as shown. The water line should be 1/4″ O.D. copper tubing or QuickConnectTM kit (WX08X10006) between the cold water line and water connection location, long enough to extend to the front of the unit (8′ [2.4m]). Installation of an easily accessible shut-off valve in the water line is required.

Minimum Clearance Dimensions with Trims Installed · 3/4″ Landing needed for cabinetry door/drawer edge
adjacent with hinge opposite of cutout. · 1-1/2″ landing needed for cabinetry door/drawer edge
with hinge adjacent to cutout
Trim

Cutout Line

A
0.75 min Hinge Opposite
Cutout.

B
1.5 min Hinge Adjacent to Cutout.

A. Option clearance Cabinet Handle next to trim. 3/4″ Minimum landing clearance (Matching Cabinet Finish) needed from cutout opening for Standard Trim.
B. Option clearance Cabinet hinge next to trim. 1-1/2″ Minimum landing clearance (Matching Cabinet Finish) needed from cutout opening for Standard Trim to clear cabinetry door hinges.

31-1000600 Rev. 0

8

31-1000731 Rev. 3

Installation Instructions – Single Standard Installation

REFRIGERATOR/FREEZER LOCATION
Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures.
Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly.
Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it fully loaded.
TOOLS AND MATERIALS REQUIRED
· Metal shears (recommended) · #1, #2 Phillips screwdriver · Flathead screwdriver · Putty knife (recommended) · Measuring tape · Drill and 1/16″, 5/64″, 3/16″, 1/2″ bits · 5/32″ concrete bit (if installing anti-tip into concrete) · 1/4″, 3/8″, 7/16″ driver/socket · 7/16″ open wrench · T10, T20, T30 driver/bit · 1/8″, 1/4″ hex driver (allen wrench) · Level · Water shut-off valves (optional but recommended) · 8′ waterline · Masking tape · Rubbing alcohol · 10″ Adjustable wrench · Center punch · Handle Kit (if applicable) · Small Rachet 1/4″ or 3/8″ · Standard Trim Kit (ZKW36V) · 90° Right Angle Driver or a minimum 8″ long, 1/4″ diameter
bit extender
HARDWARE SUPPLIED (per unit)
· Anti-Tip bracket (2) · Lag screws · Tapcon screws · 1/4″ Hex Screws · Door Hardware Kit

GROUNDING THE UNIT

WARNING

Electrical Shock

Hazard. Failure to follow these instructions can result

in death, fire, or electrical shock.

AVERTISSEMENT

Risque d’électrocution

Le non-respect de ces instructions peut occasionner un

décès, un incendie ou un choc électrique

ADVERTENCIA

Riesgo de Descarga

Si no se siguen estas instrucciones, se podrá producir

la muerte, incendios o descargas eléctricas.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

FLOORING
For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted flooring.

31-1000731 Rev. 3

9

Installation Instructions – Single Standard Installation

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard. This

appliance is top heavy. Use extreme caution with

moving to prevent tipping over which could result in

death or serious injury.

AVERTISSEMENT

Risque de

basculement. Cet électroménager est lourd du haut.

Usez d’extrême prudence en le déplaçant afin de prévenir

un basculement susceptible d’occasionner des blessures

graves ou la mort.

ADVERTENCIA

Riesgo de Caída.

Este electrodoméstico es inestable. Tenga extremo

cuidado al moverlo, a fin de evitar caídas hacia adelante

que podrían resultar en la muerte o lesiones graves.

Remove outer carton and external packing from units. T here is a box of parts taped to the outside of the
refrigerator. This box includes a toe kick for single integrated installations and door parts that will be installed after the door panel adjustments are complete. Save these parts. Inspect for damage. Ensure the flooring that the units are set is clean/ free of debris that could be collected on to, or pinched in front of the wheels and damaging the floor. Additionally, it is recommended that the floor be protected with a plastic covering through out the installation process. Remove handles from inside the refrigerator compartment. Remove hardware kits that are located inside the unit. Remove front access cover from unit by removing two 1/4″ Hex Screws. Place the cover and screws to the side for future installation. Remove two 3/8″ drive screws and two 7/16″ drive screws from each side of the unit to release it from the shipping skid. Tip the unit from the side enough to remove the shipping material from under the unit, but above the shipping skid (both sides) CAREFULLY roll the unit off the back side of the shipping skid. Handle from side only with a hand truck.

3/8″ Drive Screws

STEP 2 INSTALL WATER LINE
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation and the water dispenser (some models). The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique et le distributeur d’eau (certains modèles). La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la jarra automática de llenado y del dispensador de agua (algunos modelos). La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Shut off the main water supply. Turn on the nearest faucet long enough to clear the line of water.
,WLVUHFRPPHQGHGWKDWRXLQVWDOO a shut-off valve between the water valve and cold water pipe in a basement or adjacent cabinet. The shut-off valve should be located where it will be easily accessible.
T urn on the main water supply and flush debris. Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.

Shipping Bracket
7/16″ Drive Screws

1/4″ Hex Screws
10

31-1000731 Rev. 3

Installation Instructions – Single Standard Installation

STEP 2 INSTALL WATER LINE (Cont.)
NOTE: Saddle type shut-off valves are not recommended but are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
Route 1/4″ OD copper or SmartConnectTM (WX08X10006) plastic tubing between house cold water line and the water connection location at the front of the unit.
Tubing should be long enough to extend to the front of the unit. Allow enough tubing to accommodate bend leading into the water line connection.
NOTE: The only Café approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. The waterline will be taped to the floor using masking
tape after anti-tip bracket installation.

STEP 3 INSTALL ANTI-TIP BRACKETS

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or seri-

ous injury. Read and follow the entire installation

instructions for securing the appliance with the

anti-tip system.

AVERTISSEMENT

Risque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement

vers l’avant susceptible d’occasionner des blessures

graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer

l’électroménager sur le dispositif antibasculement.

STEP 3 INSTALL ANTI-TIP BRACKETS (Cont.)

ADVERTENCIA

Riesgo de

Caídas Estos electrodomésticos son inestables, espe-

cialmente cuando una puerta se encuentre abierta, y

deben estar asegurados a fin de evitar caídas hacia

adelante que podrían resultar en la muerte o en lesiones

graves. Lea y siga las instrucciones de instalación en su

totalidad para asegurar el electrodoméstico con el siste-

ma anti volcaduras.

Remove the anti-tip bracket(s) from the hardware kit. Secure anti-tip brackets to the floor so that the
back side of the anti-tip bracket is 22 5/8″ (57.5 cm) from the front of the enclosure (bracket hardware is provided for mounting into wood and concrete).
Measure and mark from the right side of the opening per the dimensions shown.
Mount the anti-tip bracket centered about the marks

6″ (15.2 cm) 29-3/4″ (75.6 cm)
and flush to the floor as shown. Mark 3 holes for wall mounting or 4 holes for floor mounting.
WOOD MOUNTING: Predrill with 3/16″ drill bit, 2″ deep, then install provided lag bolts with a 3/8″ driver.
CONCRETE MOUNTING: Predrill with a 5/32″ concrete bit, 2″ deep, then install provided tapcon screws with a 5/16″ driver.
NOTE: For substrates not listed above, contact a licensed contractor to determine the appropriate hardware.
The bracket must be screwed to either the FLOOR or REAR WALL.
Tape the waterline to the wall and floor as shown below. Waterline should be 10″ (25.4 cm) away from adjacent wall. Apply tape about every 5″ (12.7 cm) toward front of unit. This will keep the waterline away from the anti-tip bracket(s) and prevent the unit from rolling over the waterline during installation. Do not tape near the cabinet front in order to keep tape hidden under the unit.
5″ 10″

31-1000731 Rev. 3

11

Installation Instructions – Single Standard Installation

STEP 4 CHANGE POWER CORD

If your electrical outlet location requires a longer power cord, follow the instructions below to change to the longer power cord provided with the standard install kit.

Remove existing short power cord with string assembly:

R emove 1/4″ hex screws attaching rear access cover.

1. Unplug 3-pin power cord connector inside the machine compartment (press on sides to release locking tabs).

2. Remove power cord green ground 1/4″ hex screw.

3. Remove strain relief 1/4″ hex screw.

4. Remove string from short power cord by cutting

the string near the wire tie.

Step 2 Green Ground Screw

Step 1 3-Pin Power Cord Connector

3-Pin Power Cord Connector

Step 3 Strain Relief Screw

Rear Access Cover
Install new longer power cord:
1. Tie string around longer power cord 18 inches from strain relief and put wire tie on as shown.
2. Plug in the 3-pin connector (make sure locking tabs are engaged).
3. Install the power cord green ground screw.
4. Install the power cord strain relief. Note: Do not over tighten wire tie. Over tightening could cause damage to power cord.

STEP 4 CHANGE POWER CORD (Cont.)

WARNING

Electrical Shock Hazard.

Death or serious injury can result from failure to follow

these instructions.

· Service by a qualified service technician only.

· Disconnect power before servicing this product.

· Reconnect all grounding devices after service.

· Replace all parts and panels before operating.

AVERTISSEMENT

Risque

d’électrocution. L’omission d’observer ces instructions

peut occasionner des blessures graves ou mortelles.

· L’entretien et la réparation du produit doivent être effectués

par un technicien qualifié seulement.

· Débranchez l’alimentation électrique avant d’entretenir ou

de réparer ce produit.

· Rebranchez tous les dispositifs de mise à la terre après

l’entretien ou la réparation.

· Remettez en place toutes les pièces et tous les panneaux

avant l’utilisation

ADVERTENCIA Riesgo de Descarga Eléctrica Se podrá producir la muerte o daños graves
como resultado de no seguir estas instrucciones. · El servicio técnico deberá ser realizado por un técnico
calificado del servicio únicamente. · Desconecte el cable de corriente antes de realizar el servicio
técnico de este producto. · Vuelva a conectar todos los dispositivos de conexión a tierra
luego de realizar el servicio técnico. · Vuelva a colocar todas las piezas y paneles antes del uso.
Replace rear access cover. Make sure the power cord is properly routed through the access cover cut-out.

STEP 5 CASE TRIM INSTALLATION
Install the trim kit side rails to the exposed right and left case walls using the provided #8 Phillips head screws – 8 screws per side.

12

31-1000731 Rev. 3

Installation Instructions – Single Standard Installation

STEP 5 CASE TRIM INSTALLATION (Cont.)
Loosen the top cover hex head screws so that the slots in the top trim can slide between the hex head screws and the top cover.
Fit the top trim and side trim rails together by sliding the exposed edges of the corner trim into the right and left trim kit side rails. Align and drive the two number 8-32 Phillips head screws into the screw holes in the side rails to ensure the top trim is snugly fit to the side rails.
Tighten the top cover hex head screws so that the top trim is secured to the cabinet.

STEP 6 CONNECTING WATER SUPPLY
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).
ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la máquina de hielos automática y de la jarra de llenado automático. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

STEP 6 CONNECTING WATER SUPPLY (Cont.)

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

House Water Supply

WWRaaeFFttfeerrrieerrgeeeSSzzruuaeepptrropprlly/y

Locate and bring the tubing to the front of the cabinet. Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a bucket, then shut off the water.
Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.)
Strain Relief Screw

Copper Tubing: Slip a 1/4″ nut and ferrule over both ends of the
copper tubing. Insert the tube into the union fitting on the unit and tighten the nut to the union. Turn on the water to check for leaks. SmartConnectTM Tubing: NOTE: The only Café-approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. Insert the molded end of the tubing into the refrigerator or freezer connection. Tighten the compression nut until it is just hand-tight. Follow the instructions provided with the tubing. Overtightening can cause leaks! Turn on the water to check for leaks.

31-1000731 Rev. 3

13

Installation Instructions – Single Standard Installation

STEP 7 INSERTING/SECURING INTO CABINET SURROUND

Plug unit into the outlet in the wall.
WARNING Electrical Shock Hazard.
To reduce the risk of electrical shock, be careful during the remaining installation steps not to touch wiring or electrical components inside the compressor compartment while the appliance is plugged in and the front access cover is not in place.

AVERTISSEMENT

Trisque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement vers

l’avant susceptible d’occasionner des blessures graves ou

la mort.

AVERTISSEMENT

Risque

d’électrocution. Afin de réduire le risque

d’électrocution, usez de prudence lors des étapes

d’installation suivantes afin de ne pas toucher au câblage

ou composants électriques à l’intérieur du compartiment

du compresseur une fois que l’électroménager est branché

sans le couvercle d’accès refermé.

ADVERTENCIA

Riesgo de Caída

Estos electrodomésticos son inestables, especialmente

cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves

Place power cord on its edge and pull under product between rollers and away from the anti-tip bracket to ensure cord is not damaged during installation.

ADVERTENCIA Riesgo de Descarga Eléctrica. A fin de reducir el riesgo de descarga
eléctrica, tenga cuidado en los pasos restantes de la instalación de no tocar el cableado ni los componentes eléctricos dentro del compartimiento del compresor mientras el electrodoméstico está enchufado y la tapa de acceso frontal no está en su lugar.

As you walk the unit back into the opening, you should pull the string tight to make sure the power cord is routed underneath the unit.

String

Power Cord

Find the installation string that is attached to the front of the unit; this is to be used as you are pushing the unit back into the opening. The string is attached to the power cord; as you walk the unit back into the opening you should pull the string tight to make sure the power cord is routed underneath the unit.
Slowly walk the unit into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The back side of the top and side standard trims should be touching the cabinet surround when the units are pushed back.

Refrigerator

Cabinet Surround

Replace the waterline strain relief screw.
Strain Relief Screw
Store the excess strapping, string, and water tubing under the unit.
WARNING Electrical Shock Hazard.
Replace waterline strain relief in front rail location as shown.

Standard Trim

AVERTISSEMENT

Risque d’électrocution.

Reposez la vis de décharge de tension dans le profilé avant

comme illustré.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

ADVERTENCIA Riesgo de Descarga Eléctrica Reemplace el amortiguador de refuerzo de
la tubería de agua frente a la ubicación del riel, como se muestra.

14

31-1000731 Rev. 3

Installation Instructions – Single Standard Installation

STEP 8 LEVEL UNIT
All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit.
To level the back of the unit, turn the 7/16″ hex nut located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.
)RUIURQWOHYHOLQJXVHD7ELWDWWKHWRSRIWKH leveling leg or a 7/16″ open-end wrench at the bottom of the leveling leg.
$GMXVWKHLJKWRIXQLWWRPDWFKLQVWDOODWLRQFXWRXW opening 84″. The unit should be level and plumb with cabinetry. The front wheels must be a minimum of 1/8″ (0.3 cm) off the floor.

STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.)
Predrill 1/16″ holes is both the sides of the surround 1/2″ deep through holes in the enclosure.
Secure unit by driving four 1/4″ hex screws to both sides to surrounding cabinetry. Use 90 degree tool or alternate extension. NOTE: This step does NOT replace the anti-tip safety hardware. Refer to Step 4 Installing Anti-Tip Bracket and Step 7 Inserting/ Securing into Cabinet Surround for details on installing the anti-tip hardware. For dual installations, repeat for the second unit.
1/4″ Hex Screws

7/16″ hex nut adjusts rear wheels
T30 bit adjusts front leveling legs

7/16″ open end wrench adjusts front leveling legs

NOTICE: The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1″. If the installation requires more than 84″ height, the installer should elevate the unit on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening. If you attempt to raise the unit more than 1″, you will damage the front leveling legs and the rear leveling wheels.

STEP 9 FINAL EXTERNAL UNIT PREPARATION

2SHQWKHGRRUVWRWKHXQLW/RFDWH¿OWHUDQG¿OWHU

removal tool. Filter Compartment Door should be as shown.

Filter

5RWDWH¿OWHUóWXUQ counterclockwise

Filter Removal Tool

XVH¿OWHUUHPRYDO tool if needed).

3XOO¿OWHUWRZDUGRX to remove. NOTE: Water system will not
IXQFWLRQZLWKRXW¿OWHULQ place.

Mounting Hook

/RFDWHEOXHDUURZRQ¿OWHU5RWDWH¿OWHUWRDOLJQDUURZ as shown.
,QVHUW¿OWHULQWRSRVLWLRQDQGURWDWHóWXUQFORFNZLVH XVH¿OWHUUHPRYDOWRROLIQHHGHG

5HWXUQ¿OWHUUHPRYDOWRROWRPRXQWLQJKRRN Close the compartment door. Put the access cover back onto the unit and secure
with two 1/4″ hex head screws.

Access Cover

1/4″ Hex Screws

31-1000731 Rev. 3

15

Installation Instructions – Single Standard Installation

STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.)
If installation requires a 90° door opening, the hinge limiter pin(s) must be installed in the top hinge(s) BEFORE the unit is removed from the shipping skid. Pin is located in the hardware kit. – Open the door to expose the hole in the back hinge bracket and install the limiting pin. Pin must be fully seated in the hinge or the door will not close properly.

STEP 11 TOE KICK INSTALLATION
Use the stainless steel toe kick provided with the Single Standard Installation Kit ZKW36V. The toe kick and toe kick magnet that shipped with the unit will not be used in this type of installation.
Position toe kick on bottom portion of front access cover.

STEP 10 HANDLE INSTALLATION
Make sure the set screws in the handle caps are loosened. Place the handle over the fasteners on the door (we recommend putting the screw side of the handle toward the less visible side). Take care to support the handle so it doesn’t fall and scratch the appliance finish. Make sure both of the handle caps are resting on the face of the door.
Fastener

STEP 12 INTERNAL UNIT PREPARATION
Remove all tape, cardboard, and foam from each unit.
Remove boxed door bins from shelves. Unbox and install door bins.

Set Screw
Lock one end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Keep supporting the handle as you lock the other end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Repeat these instructions on all other handles.

16

31-1000731 Rev. 3

Installation Instructions – Single Standard Installation

STEP 13 START ICEMAKER
CAUTION To minimize the risk of personal
injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.
ATTENTION Afin de réduire le risque de blessure,
évitez tout contact avec les pièces mobiles du mécanisme d’éjection ou l’élément chauffant qui libère les cubes. Ne placez pas les doigts ou les mains sur le mécanisme de production de glace automatique lorsque l’électroménager est branché dans la prise électrique.

If the freezer is operated before the water connection is made to the icemaker, turn the ice maker off by pressing and holding the Zone Select pad until Ice Off appears.
When water has been connected to the water supply, turn the ice maker on by pressing and holding the Zone Select pad until Ice On appears.
Throw away the first full bucket of ice to allow the water line to clear.
Be sure nothing interferes with the sweep of the feeler arm.
(Appearance may vary) Icemaker

PRECAUCIÓN Para minimizar el riesgo de
lesiones personales, evite el contacto con las partes móviles del mecanismo eyector o con el elemento de calefacción que libera los cubos. No coloque los dedos ni las manos en el mecanismo de la máquina de hielo automática mientras el electrodoméstico se encuentre enchufado.
A newly-installed freezer may take 12­24 hours to begin making ice.
The icemaker will produce seven cubes per cycle– approximately 15 cycles in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

Feeler Arm
When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined together.
If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.
NOTE: Icemaker works best between 40 and 120 PSI (275-827 kPa) home water pressure.

31-1000731 Rev. 3

17

Instructions for Single Integrated Installation
New construction installation with 25″ deep openings

18

31-1000731 Rev. 3

Design Guide – Single Integrated Installation

SINGLE INTEGRATED INSTALLATION SPACE
Dimensions in parentheses are in centimeters.

36″ (91.4)

6″ (15.2)

Finished Return on both sides and top

25″ (63.5)
24 7/8″ (63.2)*

84″ (213.4)

80″ (203.2)*

18″ (45.7)

9″ (22.9)

8″ 9″ (20.3) (22.9)
ELECTRIC WATER

6″ (15.2)

2 1/2″ (6.4)

• For installation spaces deeper than 25″, it is recommended to install a spacer block per the
  dimensions shown.

Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Refer to Dim A on page 5 for clearances needed for door swing.
Water And Electrical Locations Electrical and water supply must be located as shown.
The Cutout Depth Must Be 25″.

Additional Specifications A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
:DWHUOLQHPXVWEHORFDWHGRQWKHEDFNZDOODVVKRZQ The water line should be 1/4″ O.D. copper tubing or QuickConnectTM kit (WX08X10006) between the cold water line and water connection location, long enough to extend to the front of the unit (8′ [2.4 m]). Installation of an easily accessible shut-off valve in the water line is required.
$PLQLPXPRI´FPILQLVKHGUHWXUQ matching cabinet exterior is recommended on interior on all sides and top at front of opening.

31-1000731 Rev. 3

19

Installation Instructions – Single Integrated Installation

REFRIGERATOR/FREEZER LOCATION
Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures.
Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly.
Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it fully loaded.
TOOLS AND MATERIALS REQUIRED
· Metal shears (recommended) · #1, #2 Phillips screwdriver · Flathead screwdriver · Putty knife (recommended) · Measuring tape · Drill and 1/16″, 5/64″, 3/16″, 1/2″ bits · 5/32″ concrete bit (if installing anti-tip into concrete) · 1/4″, 3/8″, 7/16″ driver/socket · 7/16″ open wrench · T10, T20, T30 driver/bit · 1/8″, 1/4″ hex driver (allen wrench) · Level · Water shut-off valves (optional but recommended) · 8′ waterline · Masking tape · Rubbing alcohol · 10″ Adjustable wrench · Center punch · Handle Kits (if applicable) · Small Ratchet 1/4″ or 3/8″ · 90° Right Angle Driver or a minimum 8″ long, 1/4″
diameter bit extender
HARDWARE SUPPLIED (per unit)
· 2 Anti-Tip brackets · 4 Lag screws · 3 Tapcon screws · (4) 1/4″ Hex Screws · 2 Hinge limiter pins · Door Trim Kit

GROUNDING THE UNIT

WARNING

Electrical Shock

Hazard. Failure to follow these instructions can

result in death, fire, or electrical shock.

AVERTISSEMENT

Risque d’électrocution

Le non-respect de ces instructions peut occasionner un

décès, un incendie ou un choc électrique

ADVERTENCIA Riesgo de Descarga
Si no se siguen estas instrucciones, se podrá producir la muerte, incendios o descargas eléctricas.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

FLOORING
For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted flooring.

20

31-1000731 Rev. 3

Installation Instructions – Single Integrated Installation

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

AVERTISSEMENT

Risque de

basculement. Cet électroménager est lourd du haut.

Usez d’extrême prudence en le déplaçant afin de prévenir

un basculement susceptible d’occasionner des blessures

graves ou la mort.

ADVERTENCIA

Riesgo de Caída.

Este electrodoméstico es inestable. Tenga extremo

cuidado al moverlo, a fin de evitar caídas hacia adelante

que podrían resultar en la muerte o lesiones graves.

Remove outer carton and external packing from units.
T here is a box of parts taped to the outside of the refrigerator. This box includes a toe kick for single integrated installations and door parts that will be installed after the door panel adjustments are complete. Save these parts.
Inspect for damage.
Ensure the flooring that the units are set is clean/ free of debris that could be collected on to, or pinched in front of the wheels and damaging the

floor. Additionally, it is recommended that the floor be protected with a plastic covering through out the installation process. Remove handles from inside the refrigerator compartment. Remove hardware kits that are located inside the unit. Remove front access cover from unit by removing two 1/4″ hex head screws. Place the cover and screws to the side for future installation. Remove two 3/8″ drive screws and two 7/16″ drive screws from each side of the unit to release it from the shipping skid. Tip the unit from the side enough to remove the shipping material from under the unit, but above the shipping skid (both sides)
3/8″ Drive Screws

Shipping Bracket

7/16″ Drive Screws

Access Cover

1/4″ Hex Head Screws

CAREFULLY roll the unit off the back side of the shipping skid.
Handle from side only with a hand truck.

31-1000731 Rev. 3

21

Installation Instructions – Single Integrated Installation

STEP 2 INSTALL WATER LINE

WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la jarra automática. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO NOT

drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line of water.
,WLVUHFRPPHQGHGWKDWRXLQVWDOO a shut-off valve between the water valve and cold water pipe in a basement or adjacent cabinet. The shut-off valve should be located where it will be easily accessible.
T urn on the main water supply and flush debris. Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are not recommended but are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
Route 1/4″ OD copper or SmartConnectTM (WX08X10006) plastic tubing between house cold water line and the water connection location at the front of the unit.
SmartConnectTM Refrigerator Tubing Kits are available. One 8′ (2.4m) water line (WX08X10006) is needed for each unit. The waterline will be taped to the floor using masking tape after anti-tip bracket installation.
Tubing should be long enough to extend to the front of the unit. Allow enough tubing to accommodate bend leading into the water line connection.
NOTE: The only Café approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home.

22

31-1000731 Rev. 3

Installation Instructions – Single Integrated Installation

STEP 3 INSTALL ANTI-TIP BRACKETS

WARNING

Tip Over Hazard.

This appliance is top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions

for securing the appliance with the anti-tip system.

AVERTISSEMENT

Risque de

basculement. Cet électroménager est lourd du haut.
Usez d’extrême prudence en le déplaçant afin de prévenir un basculement susceptible d’occasionner des blessures

graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer

l’électroménager sur le dispositif antibasculement.

ADVERTENCIA

Riesgo de

Caídas Estos electrodomésticos son inestables, espe-
cialmente cuando una puerta se encuentre abierta, y deben estar asegurados a fin de evitar caídas hacia adelante que podrían resultar en la muerte o en lesiones graves. Lea y siga las instrucciones de instalación en su totalidad para asegurar el electrodoméstico con el sistema anti volcaduras.

Remove the anti-tip bracket(s) from the hardware kit.
Anti-tip brackets should be mounted against the back wall unless the enclosure is deeper than 25-½” (64.7 cm). If the enclosure is deeper than 25-½”, the antitip bracket should be secured to the floor so that the back side of the anti-tip bracket is 25″ from the front of the enclosure (bracket hardware is provided for mounting into wood and concrete).

STEP 3 INSTALL ANTI-TIP BRACKETS (Cont.)
Measure and mark from the right side of the opening per the dimensions shown.
Mount the anti-tip bracket centered about the mark and flush to the floor as shown. Mark 3 holes for wall mounting or 4 holes for floor mounting. WOOD MOUNTING: Predrill with 3/16″ drill bit, 2″ deep, then install provided lag bolts with a 3/8″ driver. CONCRETE MOUNTING: Predrill with a 5/32″ concrete bit, 2″ deep, then install provided tapcon screws with a 5/16″ driver.
NOTE: For substrates not listed above, contact a licensed contractor to determine the appropriate hardware. The bracket must be screwed to either the FLOOR or
REAR WALL. Tape the waterline to the wall and floor as shown
below. Waterline should be 10″ (25.4 cm) away from adjacent wall. Apply tape about every 5″ (12.7 cm) toward front of unit. This will keep the waterline away from the anti-tip bracket(s) and prevent the unit from rolling over the waterline during installation. Do not tape near the cabinet front in order to keep tape hidden under the unit.
5″ 10″

6″ (15.2 cm) 29-3/4″ (75.6 cm)

31-1000731 Rev. 3

23

Installation Instructions – Single Integrated Installation

STEP 4 CONNECT WATER SUPPLY
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la máquina de hielos automática y de la jarra de llenado automático. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Locate and bring the tubing to the front of the cabinet. Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a bucket, then shut off the water.

STEP 4 CONNECT WATER SUPPLY (Cont.)

House Water Supply

WWRaaeFFttfeerrrieerrgeeeSSzzruuaeepptrropprlly/y

Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.)
Strain Relief Screw

Copper Tubing: Slip a 1/4″ nut and ferrule over both ends of the
copper tubing. Insert the tube into the union fitting on the unit and tighten the nut to the union.
Turn on the water to check for leaks. SmartConnectTM Tubing: NOTE: The only Café-approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. Insert the molded end of the tubing into the
refrigerator or freezer connection. Tighten the compression nut until it is just hand-tight. Follow the instructions provided with the tubing. Overtightening can cause leaks! Turn on the water to check for leaks.

24

31-1000731 Rev. 3

Installation Instructions – Single Integrated Installation

STEP 5 INSERTING/SECURING INTO CABINET SURROUND

Plug unit into the outlet in the wall.

WARNING Electrical Shock Hazard.
To reduce the risk of electrical shock, be careful during the remaining installation steps not to touch wiring or electrical components inside the compressor compartment while the appliance is plugged in and the front access cover is not in place.

AVERTISSEMENT

Risque

d’électrocution. Afin de réduire le risque

d’électrocution, usez de prudence lors des étapes

d’installation suivantes afin de ne pas toucher au câblage

ou composants électriques à l’intérieur du compartiment

du compresseur une fois que l’électroménager est

branché sans le couvercle d’accès refermé.

ADVERTENCIA

Riesgo de Caída

Estos electrodomésticos son inestables, especialmente

cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves

Place power cord on its edge and pull under product between rollers and away from the anti-tip bracket to ensure cord is not damaged during installation.
As you walk the unit back into the opening, you should pull the string tight to make sure the power cord is routed underneath the unit.

String

Power Cord

ADVERTENCIA Riesgo de Descarga Eléctrica. A fin de reducir el riesgo de descarga
eléctrica, tenga cuidado en los pasos restantes de la instalación de no tocar el cableado ni los componentes eléctricos dentro del compartimiento del compresor mientras el electrodoméstico está enchufado y la tapa de acceso frontal no está en su lugar.
Find the installation string that is attached to the front of the unit; this is to be used as you are pushing the unit back into the opening. The string is attached to the power cord; as you walk the unit back into the opening you should pull the string tight to make sure the power cord is routed underneath the unit.
Slowly walk the unit into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The Stainless Steel Door face should be flush with the front face of surrounding cabinets.

WARNING

Tip Over Hazard.

This appliance is top heavy, especially with the door open,

and must be secured to prevent tipping forward which could

result in death or serious injury.

Replace the waterline strain relief screw.
Strain Relief Screw

WARNING Electrical Shock Hazard.
Replace waterline strain relief in front rail location as
shown.

AVERTISSEMENT

Risque

d’électrocution. Reposez la vis de décharge de

tension dans le profilé avant comme illustré.

ADVERTENCIA Riesgo de Descarga Eléctrica Reemplace el amortiguador de refuerzo de
la tubería de agua frente a la ubicación del riel, como se muestra.
Store the excess string and water tubing under the unit.

AVERTISSEMENT

Trisque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement vers

l’avant susceptible d’occasionner des blessures graves ou

la mort.

31-1000731 Rev. 3

25

Installation Instructions – Single Integrated Installation

STEP 6 LEVEL UNIT

All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit.

To level the back of the unit, turn the 7/16″ hex nut located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.

)RUIURQWOHYHOLQJXVHD7ELWDWWKHWRSRIWKH leveling leg or a 7/16″ open-end wrench at the bottom of the leveling leg.

$GMXVWKHLJKW of unit to match installation cutout

7/16″ hex nut adjusts rear wheels

opening 84″. The

unit should be level and plumb with cabinetry. The front wheels must be a minimum of 1/8″ (0.3 cm) off

T30 bit adjusts front leveling legs

7/16″ open end wrench adjusts front leveling legs

the floor.

NOTICE: The rear leveling wheels and front leveling

legs are limited to a maximum height adjustment of 1″.

If the installation requires more than 84″ height, the

installer should elevate the unit on a sheet of plywood

or runners. Cabinetry trim could also be added across

the top of the opening to shorten the opening. If you

attempt to raise the unit more than 1″, you will damage

the front leveling legs and the rear leveling wheels.

STEP 7 Install Door Trims
Ensure anti-tip brackets are engaged with the back of the unit.
See Section Door Panel Adjustments and Trim Installation for details.

STEP 8 FINAL EXTERNAL UNIT

PREPARATION

FOR FLUSH INSTALLATION: Make sure front surface

of the door is flush

Compartment Door

with the front face of

Filter

surrounding cabinets Filter Removal BEFORE securing Tool

brackets to the

surrounding cabinetry.

Open the door(s) to WKHXQLW/RFDWH¿OWHU

Mounting Hook

DQG¿OWHUUHPRYDOWRRO)LOWHUVKRXOGEHDVVKRZQ

5 RWDWH¿OWHUóWXUQFRXQWHUFORFNZLVHXVH¿OWHU removal tool if needed).

STEP 8 FINAL EXTERNAL UNIT PREPARATION (Cont.)
3XOO¿OWHUWRZDUGRXWR remove. NOTE: Water system will not function ZLWKRXW¿OWHULQSODFH
Predrill 1/16″ holes is both the sides of the surround 1/2″ deep through holes in the enclosure.
CAUTION Use gloves and arm guard when
installing spacers.
Secure unit to surrounding cabinetry using the spacers and 1″ Phillips screws provided with the unit. On Single Door models: Secure the handle side first before moving the hinge side. On French Door models, open one door and secure that side before moving to the other side.
Open door to full extension and pass arm through opening between door and case to align spacers. Slide the spacers into place using the alignment features on the spacer and the side of the (A) housing until the spacer screw holes and housing screw holes are aligned. Drive the Phillips head screws through the housing into the surrounding cabinetry.
NOTE: This step does NOT replace the anti-tip safety hardware. Refer to Step 3 Installing Anti-Tip Bracket and Step 5 Inserting / Securing into Cabinet Surround for
A Housing

Locating feature on the housing

Locating feature on the spacer
Cabinet

A

Spacer

details on installing the anti-tip hardware. Locate blue arrow on
¿OWHU5RWDWH¿OWHUWR align arrow as shown.

,QVHUW¿OWHULQWRSRVLWLRQ DQGURWDWHóWXUQFORFNZLVHXVH ¿OWHUUHPRYDOWRROLIQHHGHG

5HWXUQ¿OWHUUHPRYDOWRRO

to

mounting hook.

Close the compartment door.

26

31-1000731 Rev. 3

Installation Instructions – Single Integrated Installation

STEP 8 FINAL EXTERNAL UNIT PREPARATION (Cont.)
Put the access cover back onto the unit and secure with two 1/4″ hex head screws.

Access Cover

1/4″ Hex Screws

If installation requires a 90° door opening, the hinge limiter pin(s) must be installed in the top hinge(s) BEFORE the unit is removed from the shipping skid. Pin is located in the hardware kit. – Open the door to expose the hole in the back hinge bracket and install the limiting pin. Pin must be fully seated in the hinge or the door will not close properly.

STEP 9 HANDLE INSTALLATION (Cont.)
Lock one end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Keep supporting the handle as you lock the other end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Repeat these instructions on all other handles.
STEP 10 TOE KICK INSTALLATION
A stainless steel toe kick and a magnet are included in the box of parts that was taped to the side of the unit.
Adhere magnet to back side of toe kick. The surface of the toe kick where the magnet is to be placed must be clean and free of foreign material. Center magnet vertically and horizontally.
Position toe kick on bottom portion of the front access cover.

STEP 9 HANDLE INSTALLATION
Make sure the set screws in the handle caps are loosened. Place the handle over the fasteners on the door (we recommend putting the screw side of the handle toward the less visible side). Take care to support the handle so it doesn’t fall and scratch the appliance finish. Make sure both of the handle caps are resting on the face of the door.
Fastener

STEP 11 INTERNAL UNIT PREPARATION
Remove all tape, cardboard, and foam from the unit.
Remove boxed door bins from shelves.
Unbox and install door bins.

Set Screw

31-1000731 Rev. 3

27

Installation Instructions – Single Integrated Installation

STEP 12 START ICEMAKER
CAUTION To minimize the risk of personal
injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.
ATTENTION Afin de réduire le risque de blessure,
évitez tout contact avec les pièces mobiles du mécanisme d’éjection ou l’élément chauffant qui libère les cubes. Ne placez pas les doigts ou les mains sur le mécanisme de production de glace automatique lorsque l’électroménager est branché dans la prise électrique.
PRECAUCIÓN Para minimizar el riesgo de
lesiones personales, evite el contacto con las partes móviles del mecanismo eyector o con el elemento de calefacción que libera los cubos. No coloque los dedos ni las manos en el mecanismo de la máquina de hielo automática mientras el electrodoméstico se encuentre enchufado.
A newly-installed freezer may take 12­24 hours to begin making ice. The icemaker will produce seven cubes per cycle– approximately 15 cycles in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the freezer is operated before the water connection is made to the icemaker, turn the ice maker off by pressing and holding the Zone Select pad until Ice Off appears. When water has been connected to the water supply, turn the icemaker on by pressing and holding the Zone Select pad until Ice On appears. Throw away the first full bucket of ice to allow the water line to clear.
(Appearance may vary) Icemaker
Feeler Arm
Be sure nothing interferes with the sweep of the feeler arm. When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together. If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink. NOTE: Icemaker works best between 40 and 120 PSI (275-827 kPa) home water pressure.

28

31-1000731 Rev. 3

Instructions for Dual Standard Installation
Existing construction installation with 24″ deep openings that are 71-1/2″ wide

31-1000731 Rev. 3

29

Design Guide – Dual Standard Installation

DUAL STANDARD INSTALLATION SPACE

Dimensions in parentheses are in centimeters.

71 1/2″ (181.6 cm)

24″ (61 cm) 6″

B 1-1/2″ Landing / Finished Spacer

(15.2 cm)

83 1/2″ min. 84 1/2″ max. (212.1-214.6 cm) *Trim will overlap additional 3/4″

54″ (137.2 cm)

44″ (111.8 cm)

8″ (20.3

18″ (45.7 cm)

9″ (22.9 cm)

cm)

9″ (22.9 cm)

ELECTRIC WATER

Finished Return on both
sides and top

9″ (22.9 cm)

9″ (22.9 cm)
ELECTRIC WATER

2 1/2″ (6.4 cm)
6″ (15.2 cm)

B Cabinet
Hinge

A ¾” Landing/Finished Spacer
A Cabinet Handle

For 24″ Deep Cutouts A trim kit (ZKW72V) is required for standard installations.
Heater Unification Kit ZKMV required
Water And Electrical Locations The recommended electrical location is shown in the diagram. If the electrical location is higher than shown, use the longer power cords provided in trim kit (ZKW72V). Follow instructions in step 6 to change power cord.
Water supply must be located as shown.
Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Refer to Dim A on page 5 for clearances needed for door swing.
Additional Specifications
· A separate 115 volt 60Hz., 15 or 20 amp power supply is recommended for each product. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
· Water line must be located on the back wall as shown. The water line should be 1/4″ O.D. copper tubing or QuickConnectTM kit (WX08X10006) between the cold water line and water connection location, long enough to extend to the front of the unit (8′ [2.4m]). Installation of an easily accessible shut-off valve in the water line is required.

Minimum Clearance Dimensions with Trims Installed · 3/4″ Landing needed for cabinetry door/drawer edge
adjacent with hinge opposite of cutout. · 1-1/2″ landing needed for cabinetry door/drawer edge
with hinge adjacent to cutout.
Trim

Cutout Line

A
0.75 min Hinge Opposite
Cutout.

B
1.5 min Hinge Adjacent to Cutout.

A. Option clearance Cabinet Handle next to trim. 3/4″ Minimum landing clearance (Matching Cabinet Finish) needed from cutout opening for Standard Trim.
B. Option clearance Cabinet hinge next to trim. 1-1/2″ Minimum landing clearance (Matching Cabinet Finish) needed from cutout opening for Standard Trim to clear cabinetry door hinges.

31-1000600 Rev. 0

30

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

REFRIGERATOR/FREEZER LOCATION
Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures.
Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly.
Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it fully loaded.
TOOLS AND MATERIALS REQUIRED
· Metal shears (recommended) · #1, #2 Phillips screwdriver · Flathead screwdriver · Putty knife (recommended) · Measuring tape · Drill and 1/16″, 5/64″, 3/16″, 1/2″ bits · 5/32″ concrete bit (if installing anti-tip into concrete) · 1/4″, 3/8″, 7/16″ driver/socket · 7/16″ open wrench · T10, T20, T30 driver/bit · 1/8″, 1/4″ hex driver (allen wrench) · Level · Water shut-off valves (optional but recommended) · 8′ waterline (one per unit requiring water hookup) · Masking tape · Rubbing alcohol · 10″ Adjustable wrench · Center punch · Heater Unification Kit (ZKMV) (for dual installation only) · Handle Kits (if applicable) · Small Rachet 1/4″ or 3/8″ · Standard Trim Kit (ZKW72V) · Stainless Steel Toe Kick (if applicable) · 90° Right Angle Driver or a minimum 8″ long, 1/4″ diameter
bit extender
HARDWARE SUPPLIED (per unit)
· Anti-Tip bracket (2) · Lag screws · Tapcon screws · 1/4″ Hex Screws · Door Hardware Kit

GROUNDING THE UNIT

WARNING

Electrical Shock

Hazard. Failure to follow these instructions can result

in death, fire, or electrical shock.

AVERTISSEMENT

Risque d’électrocution

Le non-respect de ces instructions peut occasionner un

décès, un incendie ou un choc électrique

ADVERTENCIA

Riesgo de Descarga

Si no se siguen estas instrucciones, se podrá producir

la muerte, incendios o descargas eléctricas.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

FLOORING
For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted flooring.

31-1000731 Rev. 3

31

Installation Instructions – Dual Standard Installation

KIT ZKMV PARTS SUPPLIED:
Adhesive Heater Transformer Front Mullion Trim Bracket Top Unification Bracket Bottom Front Unification Bracket Bottom Back Unification Bracket 3 1/4″ Hex Head 8-18 5/8″ Long Screws 5 1/4″ Hex Head 8-32 5/8″ Long Screws 5 3/8″ Hex Head 1/4-20 1/2″ Long Screws 4 wire clips

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard. This

appliance is top heavy. Use extreme caution with

moving to prevent tipping over which could result in

death or serious injury.

AVERTISSEMENT

Risque de

basculement. Cet électroménager est lourd du haut.

Usez d’extrême prudence en le déplaçant afin de prévenir

un basculement susceptible d’occasionner des blessures

graves ou la mort.

STEP 1 REMOVE PACKAGING (Cont.)
Remove handles from inside the refrigerator compartment.
Remove hardware kits that are located inside the unit. Remove front access cover from unit by removing
two 1/4″ Hex Screws. Place the cover and screws to the side for future installation. Remove two 3/8″ drive screws and two 7/16″ drive screws from each side of the unit to release it from the shipping skid. Tip the unit from the side enough to remove the shipping material from under the unit, but above the shipping skid (both sides) CAREFULLY roll the unit off the back side of the shipping skid. Handle from side only with a hand truck.
3/8″ Drive Screws

Shipping Bracket
7/16″ Drive Screws

1/4″ Hex Screws

ADVERTENCIA

Riesgo de Caída.

Este electrodoméstico es inestable. Tenga extremo

cuidado al moverlo, a fin de evitar caídas hacia adelante

que podrían resultar en la muerte o lesiones graves.

Remove outer carton and external packing from units. T here is a box of parts taped to the outside of the
refrigerator. This box includes a toe kick for single integrated installations and door parts that will be installed after the door panel adjustments are complete. Save these parts.
Inspect for damage. Ensure the flooring that the units are set is clean/
free of debris that could be collected on to, or pinched in front of the wheels and damaging the floor. Additionally, it is recommended that the floor be protected with a plastic covering through out the installation process.

32

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 2 INSTALL WATER LINE
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la jarra automática. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO NOT

drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Shut off the main water supply. Turn on the nearest faucet long enough to clear the line of water.
,WLVUHFRPPHQGHGWKDWRXLQVWDOO a shut-off valve between the water valve and cold water pipe in a basement or adjacent cabinet. The shut-off valve should be located where it will be easily accessible.
T urn on the main water supply and flush debris. Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.

STEP 2 INSTALL WATER LINE (Cont.)
NOTE: Saddle type shut-off valves are not recommended but are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber. Connect the jumper water line from the ZKW72V Standard Install Kit to the house cold water line. Tighten the compression nut hand tight, then tighten one additional turn with a wrench. Overtightening can cause leaks! Connect the other end of the jumper water line to the water fitting tee supplied in the ZKW72V Standard Install Kit. Tighten the compression nut hand tight, then tighten one additional turn with a wrench. Overtightening can cause leaks!
Water Line Jumper
Water Fitting Tee
Route 1/4″ OD copper or SmartConnectTM (WX08X10006) plastic tubing between water fitting tee and the water connection location at the front of each unit.
Tubing should be long enough to extend to the front of the unit. Allow enough tubing to accommodate bend leading into the water line connection.
NOTE: The only Café approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. Tape the jumper waterline and water fitting tee to the
back wall. The waterlines will be taped to the floor using masking tape after anti-tip bracket installation.

31-1000731 Rev. 3

33

Installation Instructions – Dual Standard Installation

STEP 3 PREPARING UNIT FOR INSTALLATION – DUAL INSTALL

Unpack the heater Unification Kit (ZKMV) and make sure all of the components on the list are included.
NOTE: Ensure the heater connector cord is toward the top of the unit when installed. Place the right hand unit in front of the installation
opening in a way that the unit is in front of the intended installed location.
Install adhesive heater on the outside of the unit to the left side of the case. Install heater 4″ below the case top. Heater should be centered front to back on the metal case.
8VHFOLSVWRDGKHUHORRVHZLUHWLJKWOWRVLGHRIFDVHDV shown. Clean the side using rubbing alcohol to ensure proper clip adhesion.
Clips

Install the transformer into the case top assembly: 1. Remove cover top by removing eight #8 hex screws
and keep aside for assembling back the cover top.
2. Place the transformer provided in ZKMV kit onto the case top. Secure transformer with (1/4″) hex screw to case top in existing hole at the rear right side of the top control housing.
3. Connect the 2 pin transformer connector to the heater connector and 3 pin connector to panel control, make sure locking tabs are engaged.
4. NOTE: Verify the master switch is on.
5. Assemble the cover top with screws save from previous step.

Plug 2 position heater connector to 2 position transformer connector with blue and yellow wires.

Screw hole location for transformer.
Transformer

Remove empty connector housing before connecting transformer.

Control Housing 4″

Adhesive Heater

Master Switch

NOTE: The heater installation is available only on the left side of compatible models.

WARNING

Electrical Shock

Hazard. To avoid the risk of electric shock, make

sure the power cord is not plugged into the wall outlet.

Plug 3 position transformer connector with black and white wires to 3 position harness connector with brown and orange wires.
Enclosure assembly above is shown with cover removed.

AVERTISSEMENT

Risque

d’électrocution. Pour prévenir le risque

d’électrocution, assurez-vous que le cordon électrique

n’est pas branché dans la prise murale.

ADVERTENCIA

Riesgo de Descarga

Si no se siguen estas instrucciones, se podrá producir

la muerte, incendios o descargas eléctricas.

34

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 4 INSTALL ANTI-TIP BRACKETS

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions

for securing the appliance with the anti-tip system.

AVERTISSEMENT

Risque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement

vers l’avant susceptible d’occasionner des blessures

graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer

l’électroménager sur le dispositif antibasculement.

ADVERTENCIA

Riesgo de

Caídas Estos electrodomésticos son inestables, espe-

cialmente cuando una puerta se encuentre abierta, y

deben estar asegurados a fin de evitar caídas hacia

adelante que podrían resultar en la muerte o en lesiones

graves. Lea y siga las instrucciones de instalación en su

totalidad para asegurar el electrodoméstico con el sistema

anti volcaduras.

Remove the anti-tip bracket(s) from the hardware kit.
Secure anti-tip brackets to the floor so that the back side of the anti-tip bracket is 22 5/8″ (57.5 cm) from the front of the enclosure (bracket hardware is provided for mounting into wood and concrete).
Measure and mark from the right side of the opening per the dimensions shown.

Mount the anti-tip bracket centered about the marks and flush to the floor as shown. Mark 3 holes for wall mounting or 4 holes for floor mounting.
WOOD MOUNTING: Predrill with 3/16″ drill bit, 2″ deep, then install provided lag bolts with a 3/8″ driver.
CONCRETE MOUNTING: Predrill with a 5/32″ concrete bit, 2″ deep, then install provided tapcon screws with a 5/16″ driver.
NOTE: For substrates not listed above, contact a licensed contractor to determine the appropriate hardware.
The bracket must be screwed to either the FLOOR or REAR WALL.
Tape the waterline to the wall and floor as shown below. Waterline should be 10″ (25.4 cm) away from adjacent wall. Apply tape about every 5″ (12.7 cm) toward front of unit. This will keep the waterline away from the anti-tip bracket(s) and prevent the unit from rolling over the waterline during installation. Do not tape near the cabinet front in order to keep tape hidden under the unit.

5″ 10″

5″ 10″

6″ (15.2 cm) 29-3/4″ (75.6 cm) 41-1/2″ (105.4 cm) 65-1/2″ (166.4 cm)

31-1000731 Rev. 3

35

Installation Instructions – Dual Standard Installation

STEP 5 JOINING DUAL INSTALLED UNITS

TOP UNIFICATION

BOTTOM FRONT UNIFICATION

Loosen the middle two screws, remove the two rear screws.

Install the bottom front unification bracket using a 3/8″ driver (4 screws).

Assemble the bracket to the middle screws and reassemble the rear screws.

Tighten screws to tie units together.

Unification Bracket

8QL¿FDWLRQ%UDFNHW

Front of appliances BOTTOM BACK UNIFICATION Loosen the two bottom screws of rear access covers of
both units and remove the top screws. Hang the unification bracket to the bottom screws and
reassemble the screws at the top Tighten screws to tie units together.
8QL¿FDWLRQ Bracket

36

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 6 CHANGE POWER CORD

If your electrical outlet location requires a longer power cord, follow the instructions below to change to the longer power cord provided with the standard install kit.
Remove existing short power cord with string assembly:
R emove 1/4″ hex screws attaching rear access cover. 1. Unplug 3-pin power cord connector inside the machine compartment (press on sides to release locking tabs).
2. Remove power cord green ground 1/4″ hex screw.
3. Remove strain relief 1/4″ hex screw.
4. Remove string from short power cord by cutting the string near the wire tie.

Step 2 Green Ground Screw

Step 1 3-Pin Power Cord Connector
3-Pin Power Cord Connector

Step 3 Strain Relief Screw

Install new longer power cord:
1. Tie string around longer power cord 18 inches from strain relief and put wire tie on as shown.
2. Plug in the 3-pin connector (make sure locking tabs are engaged).
3. Install the power cord green ground screw.
4. Install the power cord strain relief.
Note: Do not over tighten wire tie. Over tightening could cause damage to power cord.

Rear Access Cover

STEP 6 CHANGE POWER CORD (Cont.)

WARNING

Electrical Shock Hazard.

Death or serious injury can result from failure to follow

these instructions.

· Service by a qualified service technician only.

· Disconnect power before servicing this product.

· Reconnect all grounding devices after service.

· Replace all parts and panels before operating.

AVERTISSEMENT

Risque

d’électrocution. L’omission d’observer ces instructions

peut occasionner des blessures graves ou mortelles.

· L’entretien et la réparation du produit doivent être effectués

par un technicien qualifié seulement.

· Débranchez l’alimentation électrique avant d’entretenir ou

de réparer ce produit.

· Rebranchez tous les dispositifs de mise à la terre après

l’entretien ou la réparation.

· Remettez en place toutes les pièces et tous les panneaux

avant l’utilisation

ADVERTENCIA Riesgo de Descarga Eléctrica Se podrá producir la muerte o daños graves
como resultado de no seguir estas instrucciones. · El servicio técnico deberá ser realizado por un técnico
calificado del servicio únicamente. · Desconecte el cable de corriente antes de realizar el servicio
técnico de este producto. · Vuelva a conectar todos los dispositivos de conexión a tierra
luego de realizar el servicio técnico. · Vuelva a colocar todas las piezas y paneles antes del uso.
Replace rear access cover. Make sure the power cord is properly routed through the access cover cut-out.

STEP 7 CASE TRIM INSTALLATION
Install the trim kit side rails to the exposed right and left case walls using the provided #8 Phillips head screws 8 screws per side.

31-1000731 Rev. 3

37

Installation Instructions – Dual Standard Installation

STEP 7 CASE TRIM INSTALLATION (Cont.)
Loosen the top cover hex head screws so that the slots in the top trim can slide between the hex head screws and the top cover.
Fit the top trim and side trim rails together by sliding the exposed edges of the corner trim into the right and left trim kit side rails. Align and drive the two number 8-32 Phillips head screws into the screw holes in the side rails to ensure the top trim is snugly fit to the side rails.
Tighten the top cover hex head screws so that the top trim is secured to the cabinet.

STEP 8 CONNECTING WATER SUPPLY
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la máquina de hielos automática y de la jarra de llenado automático. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

House Water Supply

WWRaaeFFttfeerrrieerrgeeeSSzzruuaeepptrropprlly/y

Locate and bring the tubing to the front of the cabinet. Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a bucket, then shut off the water.

38

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 8 CONNECTING WATER SUPPLY (Cont.)
Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.)
Strain Relief Screw
Copper Tubing: Slip a 1/4″ nut and ferrule over both ends of the
copper tubing. Insert the tube into the union fitting on the unit and tighten the nut to the union. Turn on the water to check for leaks. SmartConnectTM Tubing: NOTE: The only Café-approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. Insert the molded end of the tubing into the refrigerator or freezer connection. Tighten the compression nut until it is just hand-tight. Follow the instructions provided with the tubing. Overtightening can cause leaks! Turn on the water to check for leaks.

STEP 9 INSERTING/SECURING INTO CABINET SURROUND
Plug both units to the outlet in the wall.
WARNING Electrical Shock Hazard.
To reduce the risk of electrical shock, be careful during the remaining installation steps not to touch wiring or electrical components inside the compressor compartment while the appliance is plugged in and the front access cover is not in place.

AVERTISSEMENT

Risque

d’électrocution. Afin de réduire le risque

d’électrocution, usez de prudence lors des étapes

d’installation suivantes afin de ne pas toucher au câblage

ou composants électriques à l’intérieur du compartiment

du compresseur une fois que l’électroménager est

branché sans le couvercle d’accès refermé.

ADVERTENCIA Riesgo de Descarga Eléctrica. A fin de reducir el riesgo de descarga
eléctrica, tenga cuidado en los pasos restantes de la instalación de no tocar el cableado ni los componentes eléctricos dentro del compartimiento del compresor mientras el electrodoméstico está enchufado y la tapa de acceso frontal no está en su lugar.

Find the installation string that is attached to the front of the unit; this is to be used as you are pushing the unit back into the opening. The string is attached to the power cord; as you walk the unit back into the opening you should pull the string tight to make sure the power cord is routed underneath the unit.
Slowly walk both units into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The back side of the top and side standard trims should be touching the cabinet surround when the units are pushed back.

Refrigerator

Cabinet Surround

Standard Trim

31-1000731 Rev. 3

39

Installation Instructions – Dual Standard Installation

STEP 9 INSERTING/SECURING INTO CABINET SURROUND (Cont.)

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury.

Replace the waterline strain relief screw.
Strain Relief Screw

AVERTISSEMENT

Trisque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement

vers l’avant susceptible d’occasionner des blessures

graves ou la mort.

ADVERTENCIA

Riesgo de Caída

Estos electrodomésticos son inestables, especialmente

cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves

Place power cord on its edge and pull under product between rollers and away from the anti-tip bracket to ensure cord is not damaged during installation.
As you walk the unit back into the opening, you should pull the string tight to make sure the power cord is routed underneath the unit.

String

Power Cord

Store the excess strapping, string, and water tubing under the unit.
WARNING Electrical Shock Hazard.
Replace waterline strain relief in front rail location as shown.
AVERTISSEMENT Risque d’électrocution.
Reposez la vis de décharge de tension dans le profilé avant comme illustré.
ADVERTENCIA Riesgo de Descarga Eléctrica Reemplace el amortiguador de refuerzo de
la tubería de agua frente a la ubicación del riel, como se muestra.

40

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 10 LEVEL UNIT
All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit.
To level the back of the unit, turn the 7/16″ hex nut located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.
)RUIURQWOHYHOLQJXVHD7ELWDWWKHWRSRIWKH leveling leg or a 7/16″ open-end wrench at the bottom of the leveling leg.
$GMXVWKHLJKWRIXQLWWRPDWFKLQVWDOODWLRQFXWRXW opening 84″. The unit should be level and plumb with cabinetry. The front wheels must be a minimum of 1/8″ (0.3 cm) off the floor.

7/16″ hex nut adjusts rear wheels

T30 bit adjusts front leveling legs

7/16″ open end wrench adjusts front leveling legs

NOTICE: The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1″. If the installation requires more than 84″ height, the installer should elevate the unit on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening. If you attempt to raise the unit more than 1″, you will damage the front leveling legs and the rear leveling wheels.

STEP 11 FINAL EXTERNAL UNIT

PREPARATION

Open the doors to Compartment Door

the units. Locate

¿OWHUDQG¿OWHU removal tool. Filter

Filter Removal Tool

should be as shown.

Filter

5RWDWH¿OWHUóWXUQ counterclockwise XVH¿OWHUUHPRYDO tool if needed).

Mounting Hook

3XOO¿OWHUWRZDUGRXWR remove. NOTE: Water system will not function
ZLWKRXW¿OWHULQSODFH

Predrill 1/16″ holes is both the sides of the surround 1/2″ deep through holes in the enclosure.

Secure unit by driving four 1/4″ hex screws to both sides to surrounding cabinetry. Use 90 degree tool or alternate extension. NOTE: This step does NOT replace the anti-tip safety hardware. Refer to Step 4 Installing Anti-Tip Bracket and Step 7 Inserting/ Securing into Cabinet Surround for details on installing the anti-tip hardware. For dual installations, repeat for the second unit.

1/4″ Hex Screws

/RFDWHEOXHDUURZRQ¿OWHU5RWDWH¿OWHUWRDOLJQDUURZ as shown.

,QVHUW¿OWHULQWRSRVLWLRQDQGURWDWHóWXUQFORFNZLVH XVH¿OWHUUHPRYDOWRROLIQHHGHG

31-1000731 Rev. 3

5HWXUQ¿OWHUUHPRYDOWRROWRPRXQWLQJKRRN Close the compartment door.
41

Installation Instructions – Dual Standard Installation

STEP 11 FINAL EXTERNAL UNIT PREPARATION (Cont.)
Put the access cover back onto the unit and secure with two 1/4″ hex head screws.

“Dart”

Mullion Trim

Access Cover

1/4″ Hex Screws

2QWKHVLGHRIWKHDFFHVVFRYHUWKDWZLOOIDFHWKHPLGGOH of the installation, drive two 1/4″ hex head screws. These screws will enhance attachment of mullion trim. Repeat on the second access cover.

Access Cover Hole Locations
Mullion Trim Installation Open all doors and drawers. $OLJQWRSRI0XOOLRQ7ULPZLWKWRSRIFRQWUROSDQHOV ,QVWDOOPXOOLRQWULPEHWZHHQWKHWZRXQLWVESXVKLQJ
the dart in the area between the units. (QVXUHWULPLVIXOOVHDWHGDJDLQVWFDVH$GMXVWLI
necessary.

NOTE: Doors/Drawers not shown for clarity.
Open both water filter access doors to 90°.
Snap the trim bracket between the water filter access enclosures above displays.
If installation requires a 90° door opening, the hinge limiter pin(s) must be installed in the top hinge(s). – Open the door to expose the hole in the back hinge bracket and install the limiting pin. Pin must be fully seated in the hinge or the door will not close properly.

42

31-1000731 Rev. 3

Installation Instructions – Dual Standard Installation

STEP 12 HANDLE INSTALLATION
Make sure the set screws in the handle caps are loosened. Place the handle over the fasteners on the door (we recommend putting the screw side of the handle toward the less visible side). Take care to support the handle so it doesn’t fall and scratch the appliance finish. Make sure both of the handle caps are resting on the face of the door.

STEP 14 INTERNAL UNIT PREPARATION
Remove all tape, cardboard, and foam from each unit. Remove boxed door bins from shelves. Unbox and install door bins.
STEP 15 START ICEMAKER

Fastener
Set Screw
Lock one end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Keep supporting the handle as you lock the other end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Repeat these instructions on all other handles.
STEP 13 TOE KICK INSTALLATION
A stainless steel toe kick and a magnet are included in the box of parts that was taped to the side of each refrigerator. A full width toe kick (ZKK72R) for dual standard installations can be purchased separately.
For individual toe kicks, adhere magnets to the back side of the toe kicks. The surface of the toe kick where the magnet is to be placed must be clean and free of foreign material. Center magnets vertically and horizontally.
Position toe kick(s) on bottom portion of front access covers.

CAUTION To minimize the risk of personal
injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.

ATTENTION Afin de réduire le risque de blessure,
évitez tout contact avec les pièces mobiles du mécanisme d’éjection ou l’élément chauffant qui libère les cubes. Ne placez pas les doigts ou les mains sur le mécanisme de production de glace automatique lorsque l’électroménager est branché dans la prise électrique.

PRECAUCIÓN Para minimizar el riesgo de
lesiones personales, evite el contacto con las partes móviles del mecanismo eyector o con el elemento de calefacción que libera los cubos. No coloque los dedos ni las manos en el mecanismo de la máquina de hielo automática mientras el electrodoméstico se encuentre enchufado.

A newly-installed freezer may take 12­24 hours to begin making ice.

The icemaker will produce seven cubes per cycle– approximately 15 cycles in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the freezer is operated before the water connection is made to the icemaker, turn the ice maker off by pressing and holding the Zone Select pad until Ice Off appears.

When water has been connected to the water supply, turn the ice maker on by pressing and holding the Zone Select pad until Ice On appears.

Throw away the first full bucket of ice to allow the water

line to clear.

(Appearance may vary)

Be sure nothing interferes with

Icemaker

the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.

It is normal for several cubes to

be joined together. If ice is not used frequently, old

Feeler Arm

ice cubes will become cloudy, taste stale and shrink.

NOTE: Icemaker works best between 40 and 120 PSI (275-827 kPa) home water pressure.

31-1000731 Rev. 3

43

Instructions for Dual Integrated Installation (Single Door models only)
New construction installation with 25″ deep openings

44

31-1000731 Rev. 3

Design Guide – Dual Integrated Installation
DUAL INTEGRATED INSTALLATION SPACE (Single Door models only)
Dimensions in parentheses are in centimeters.

72″ (182.8 cm)

6″ (15.2 cm) Finished Return on both sides and top

25″ (63.5 cm)
24 7/8″ (63.2 cm)*

84″ (213.4 cm)

54″ (137.2 cm)
44″ (111.8 cm)

18″ (45.7 cm)

9″ (22.9 cm)

8″

9″

(20.3 cm) (22.9 cm)

ELECTRIC WATER

9″ (22.9 cm)

80″ (203.2 cm)*

9″ (22.9 cm)
ELECTRIC WATER

6″ (15.2 cm)
2 1/2″ (6.4 cm) * For installation spaces deeper than 25″, it is recommended
to install a spacer block per the dimensions shown.

31-1000731 Rev. 3

45

Design Guide – Dual Integrated Installation

DUAL INTEGRATED INSTALLATION SPACE

Water And Electrical Locations Electrical and water supply must be located as shown.
The Cutout Depth Must Be 25″ Cutout is based on installation of 2 Single Door products with a left-and-right hand door swing.
Heater Unification Kit ZKMV required.
Product Clearances These units are equipped with a 2-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Refer to Dim A on page 5 for clearances needed for door swing.

Additional Specifications · A separate 115 volt 60Hz., 15 or 20 amp power supply
is recommended for each product. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
· Water line must be located on the back wall as shown. The water line should be 1/4″ O.D. copper tubing or QuickConnect kitTM (WX08X10006) between the cold water line and water connection location, long enough to extend to the front of the unit (8′ [2.4m]). Installation of an easily accessible shut-off valve in the water line is required.

· A minimum of 6″ finished return matching cabinet exterior is recommended on interior on all sides and top at front of opening.

· Installations with 6″ (15.2 cm) or less between units require Heater Unification Kit.

REFRIGERATOR/FREEZER LOCATION
Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures.
Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly.
Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it fully loaded.
HARDWARE SUPPLIED (per unit)
· 2 Anti-Tip brackets · Lag screws · Tapcon screws · 1/4″ hex screws · 2 Hinge limiter pins · Door Hardware Kit · Toe kick magnet

TOOLS AND MATERIALS REQUIRED
· Metal shears (recommended) · #1, #2 Phillips screwdriver · Flathead screwdriver · Putty knife (recommended) · Measuring tape · Drill and 1/16″, 5/64″, 3/16″, 1/2″ bits · 5/32″ concrete bit (if installing anti-tip into concrete) · 1/4″, 3/8″, 7/16″ driver/socket · 7/16″ open wrench · T10, T20, T30 driver/bit · 1/8″, 1/4″ hex driver (allen wrench) · Level · Water shut-off valves (optional but recommended) · 8′ waterline (one per unit requiring water hookup) · Masking tape · Rubbing alcohol · 10″ Adjustable wrench · Center punch · Heater Unification Kit (ZKMV) · Handle Kits (if applicable) · Small Rachet 1/4″ or 3/8″ · 90° Right Angle Driver or a minimum 8″ long, 1/4″
diameter bit extender

46

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

KIT ZKMV PARTS SUPPLIED:
Adhesive Heater Transformer Front Mullion Trim Bracket Top Unification Bracket Bottom Front Unification Bracket Bottom Back Unification Bracket 3 1/4″ Hex Head 8-18 5/8″ Long Screws 5 1/4″ Hex Head 8-32 5/8″ Long Screws 5 3/8″ Hex Head 1/4-20 1/2″ Long Screws 4 wire clips

GROUNDING THE UNIT

WARNING

Electrical Shock

Hazard. Failure to follow these instructions can

result in death, fire, or electrical shock.

AVERTISSEMENT

Risque d’électrocution

Le non-respect de ces instructions peut occasionner un

décès, un incendie ou un choc électrique

ADVERTENCIA Riesgo de Descarga
Si no se siguen estas instrucciones, se podrá producir la muerte, incendios o descargas eléctricas.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

FLOORING
For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted flooring.

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard. This

appliance is top heavy. Use extreme caution with

moving to prevent tipping over which could result in

death or serious injury.

AVERTISSEMENT

Risque de

basculement. Cet électroménager est lourd du haut.

Usez d’extrême prudence en le déplaçant afin de prévenir

un basculement susceptible d’occasionner des blessures

graves ou la mort.

ADVERTENCIA

Riesgo de Caída.

Este electrodoméstico es inestable. Tenga extremo

cuidado al moverlo, a fin de evitar caídas hacia adelante

que podrían resultar en la muerte o lesiones graves.

Remove outer carton and external packing from units.
There is a box of parts taped to the outside of the refrigerator. This box includes a toe kick for single integrated installations and door parts that will be installed after the door panel adjustments are complete. Save these parts.
Inspect for damage.
Ensure the flooring that the units are set is clean/ free of debris that could be collected on to, or pinched in front of the wheels and damaging the floor. Additionally, it is recommended that the floor be protected with a plastic covering through out the installation process.

5HPRYHKDQGOHVIURPLQVLGHWKHUHIULJHUDWRU compartment.
Remove hardware kits that are located inside the unit.

31-1000731 Rev. 3

47

Installation Instructions – Dual Integrated Installation

STEP 1 REMOVE PACKAGING (cont.)
Remove front access cover from unit by removing two 1/4″ hex head screws. Place the cover and screws to the side for future installation.
3/8″ Drive Screws

Shipping Bracket

7/16″ Drive Screws

1/4″ Hex Head Screws

Remove two 3/8″ drive screws and two 7/16″ drive screws from each side of the unit to release it from the shipping skid. Tip the unit from the side enough to remove the shipping material from under the unit, but above the shipping skid (both sides)
CAREFULLY roll the unit off the back side of the shipping skid.
Handle from side only with a hand truck.

STEP 2 INSTALL WATER LINE
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et 120 psi. (275 à 827 kPa).
ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la máquina de hielos automática. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

STEP 2 INSTALL WATER LINE (cont.)

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line of water.
,WLVUHFRPPHQGHGWKDWRXLQVWDOO a shut-off valve between the water valve and cold water pipe in a basement or adjacent cabinet. The shut-off valve should be located where it will be easily accessible.
T urn on the main water supply and flush debris. Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are not recommended but are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
Route 1/4″ OD copper or SmartConnectTM (WX08X10006) plastic tubing between house cold water line and the water connection location at the front of each unit.
SmartConnectTM Refrigerator Tubing Kits are available. One 8′ (2.4m) water line (WX08X10006) is needed for each unit. The waterline(s) will be taped to the floor using masking tape after anti-tip bracket installation.

Tubing should be long enough to extend to the front of the unit. Allow enough tubing to accommodate bend leading into the water line connection.
NOTE: The only Café approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home.

48

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

STEP 3 PREPARING UNIT FOR INSTALLATION

Unpack the heater Unification Kit (ZKMV) and make sure all of the components on the list are included.

NOTE: Ensure the heater connector cord is toward the top of the unit when installed.

Place the right hand unit in front of the installation opening in a way that the unit is in front of the intended installed location. Make sure unit remains unplugged and off.

Install adhesive heater on the outside of the right hand unit to the left side of the case. Install heater 4″ below the case top. Heater should be centered front to back on the metal case.

Use clips to adhere loose wire tightly to side of case as shown. Clean the side using rubbing alcohol to ensure proper clip adhesion.

NOTE: The heater installation is available only on the left

side of compatible models.

Clips

Install the transformer into the case top assembly:

1. Remove cover top by removing eight #8 hex screws and keep aside for assembling back the cover top.

2. Place the transformer provided in ZKMV kit onto the case top. Secure transformer with (1/4″) hex screw to case top in existing hole at the rear right side of the top control housing.

3. Connect the 2 pin transformer connector to the heater connector and 3 pin connector to panel control, make sure locking tabs are engaged.

4. NOTE: Verify the master switch is on.

5. Assemble the cover top with screws save from

previous step.
Plug 2 position heater connector to 2 position transformer connector with blue and yellow wires.

Screw hole location for transformer.
Transformer

Remove empty connector housing before connecting transformer.

Control Housing

4″
Adhesive Heater

WARNING

Electrical Shock

Hazard. To avoid the risk of electric shock, make

sure the power cord is not plugged into the wall outlet.

AVERTISSEMENT

Risque

d’électrocution. Pour prévenir le risque

d’électrocution, assurez-vous que le cordon électrique

n’est pas branché dans la prise murale.

ADVERTENCIA Riesgo de Descarga
Si no se siguen estas instrucciones, se podrá producir la muerte, incendios o descargas eléctricas.

Master Switch
Plug 3 position transformer connector with black and white wires to 3 position harness connector with brown and orange wires.
Enclosure assembly above is shown with cover removed.

31-1000731 Rev. 3

49

Installation Instructions – Dual Integrated Installation

STEP 4 INSTALL ANTI-TIP BRACKETS

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions

for securing the appliance with the anti-tip system.

AVERTISSEMENT

Risque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement

vers l’avant susceptible d’occasionner des blessures

graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer

l’électroménager sur le dispositif antibasculement.

ADVERTENCIA

Riesgo de Caídas

Estos electrodomésticos son inestables, especialmente

cuando una puerta se encuentre abierta, y deben estar ase-

gurados a fin de evitar caídas hacia adelante que podrían

resultar en la muerte o en lesiones graves. Lea y siga las

instrucciones de instalación en su totalidad para asegurar el

electrodoméstico con el sistema anti volcaduras.

Remove the anti-tip brackets from the hardware kit.
Anti-tip brackets should be mounted against the back wall unless the enclosure is deeper than 25-1/2″ (64.7 cm). If the enclosure is deeper than 25-1/2″, the anti-tip bracket should be secured to the floor so that the back side of the anti-tip bracket is 25″ from the front of the enclosure (bracket hardware is provided for mounting into wood and concrete).
Measure and mark from the right side of the opening per dimensions shown.

STEP 4 INSTALL ANTI-TIP BRACKET (Cont.)
Mount the anti-tip bracket centered about the marks and flush to the floor as shown. Mark 3 holes for wall mounting or 4 holes for floor mounting.
WOOD MOUNTING: Predrill with 3/16″ drill bit, 2″ deep, then install provided lag bolts with a 3/8″ driver.
CONCRETE MOUNTING: Predrill with a 5/32″ concrete bit, 2″ deep, then install provided tapcon screws with a 5/16″ driver.
NOTE: For substrates not listed above, contact a licensed contractor to determine the appropriate hardware.
The bracket must be screwed to either the FLOOR or REAR WALL.
Tape the waterline to the wall and floor as shown below. Waterline should be 10″ (25.4 cm) away from adjacent wall. Apply tape about every 5″ (12.7 cm) toward front of unit. This will keep the waterline away from the anti-tip bracket(s) and prevent the unit from rolling over the waterline during installation. Do not tape near the cabinet front in order to keep tape hidden under the unit.

5″ 10″

5″ 10″

6″ (15.2 cm) 29-3/4″ (75.6 cm) 41-1/2″ (105.4 cm) 65-1/2″ (166.4 cm)

50

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

STEP 5 JOINING DUAL INSTALLED UNITS

TOP UNIFICATION

BOTTOM FRONT UNIFICATION

Loosen the middle two screws, remove the two rear screws.

Install the bottom front unification bracket using a 3/8″ driver (4 screws).

Assemble the bracket to the middle screws and reassemble the rear screws.

Tighten screws to tie units together.

Unification Bracket

8QL¿FDWLRQ%UDFNHW

Front of appliances BOTTOM BACK UNIFICATION Loosen the two bottom screws of rear access covers of
both units and remove the top screws. Hang the unification bracket to the bottom screws and
reassemble the screws at the top Tighten screws to tie units together.
8QL¿FDWLRQ Bracket

31-1000731 Rev. 3

51

Installation Instructions – Dual Integrated Installation

STEP 6 CONNECTING WATER SUPPLY
WARNING Connect to potable water supply
only. A cold water supply is required for automatic icemaker operationThe water pressure must be between 40 and 120 psi (275-827 kilopascals).

AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. Une alimentation d’eau froide est requise pour faire fonctionner la machine à glaçons et le pichet à remplissage automatique. La pression d’eau doit se situer entre 40 et
120 psi. (275 à 827 kPa).

ADVERTENCIA Realice la conexión a un
suministro de agua potable únicamente. Se requiere un suministro de agua fría para el funcionamiento de la máquina de hielos automática. La presión del agua deberá estar entre 40 y 120 p.s.i. (275 ­ 827 kPa).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

AVERTISSEMENT

RISQUE DE DÉCHARGE ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

PELIGRO DE DESCARGA ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

STEP 6 CONNECTING WATER SUPPLY
Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.)
Strain Relief Screw
Copper Tubing: Slip a 1/4″ nut and ferrule over both ends of the
copper tubing. Insert the tube into the union fitting on the unit and tighten the nut to the union. Turn on the water to check for leaks. SmartConnectTM Tubing: NOTE: The only Café-approved plastic tubing is supplied in the SmartConnectTM Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home. Insert the molded end of the tubing into the refrigerator or freezer connection. Tighten the compression nut until it is just hand-tight. Follow the instructions provided with the tubing. Overtightening can cause leaks! Turn on the water to check for leaks.

House Water Supply

WWRaaeFFttfeerrrieerrgeeeSSzzruuaeepptrropprlly/y

Locate and bring the tubing to the front of the cabinet.
Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the water.

52

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

STEP 7 INSERTING/SECURING INTO CABINET SURROUND
WARNING Electrical Shock Hazard.
To reduce the risk of electrical shock, be careful during the remaining installation steps not to touch wiring or electrical components inside the compressor compartment while the appliance is plugged in and the front access cover is not in place.

AVERTISSEMENT

Risque

d’électrocution. Afin de réduire le risque
d’électrocution, usez de prudence lors des étapes d’installation suivantes afin de ne pas toucher au câblage ou composants électriques à l’intérieur du compartiment du compresseur une fois que l’électroménager est branché sans le couvercle d’accès refermé.

ADVERTENCIA

Riesgo de Descarga

Eléctrica. A fin de reducir el riesgo de descarga

eléctrica, tenga cuidado en los pasos restantes de la

instalación de no tocar el cableado ni los componentes

eléctricos dentro del compartimiento del compresor

mientras el electrodoméstico está enchufado y la tapa de

acceso frontal no está en su lugar.

Plug both units into the outlet in the wall.
Find the installation string that is attached to the front of the unit; this is to be used as you are pushing the unit back into the opening. The string is attached to the power cord; as you walk the unit back into the opening you should pull the string tight to make sure the power cord is routed underneath the unit.
Slowly walk both units into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The Stainless Steel Door face should be flush with the front face of surrounding cabinets.

STEP 7 INSERTING/SECURING INTO CABINET SURROUND

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury.

AVERTISSEMENT

Trisque de

basculement. Ces électroménagers sont lourds du

haut, notamment lorsqu’une porte est ouverte, de sorte

qu’ils doivent être fixés pour prévenir un basculement

vers l’avant susceptible d’occasionner des blessures

graves ou la mort.

ADVERTENCIA

Riesgo de

Caída. Estos electrodomésticos son inestables,

especialmente cuando una puerta se encuentre abierta,

y deben estar asegurados a fin de evitar caídas hacia

adelante que podrían resultar en la muerte o en lesiones

graves

Place power cord on its edge and pull under product between rollers and away from the anti-tip bracket to ensure cord is not damaged during installation.
As you walk the unit back into the opening, you should pull the string tight to make sure the power cord is routed underneath the unit.

String

Power Cord

31-1000731 Rev. 3

53

Installation Instructions – Dual Integrated Installation

STEP 7 INSERTING/SECURING INTO CABINET SURROUND (Cont.)
Replace the waterline strain relief screw.
Strain Relief Screw

Store the excess string, and water tubing under the unit.
WARNING Electrical Shock Hazard.
Replace waterline strain relief in front rail location as shown.

AVERTISSEMENT

Risque

d’électrocution. Reposez la vis de décharge de

tension dans le profilé avant comme illustré.

ADVERTENCIA Riesgo de Descarga Eléctrica Reemplace el amortiguador de refuerzo de
la tubería de agua frente a la ubicación del riel, como se muestra.

STEP 8 LEVEL UNIT
All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit. To level the back of the unit, turn the 7/16″ hex nut
located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.
)RUIURQWOHYHOLQJXVHD7ELWDWWKHWRSRIWKH leveling leg or a 7/16″ open-end wrench at the bottom of the leveling leg.
$GMXVWKHLJKWRIXQLWWRPDWFKLQVWDOODWLRQFXWRXW opening 84″. The unit should be level and plumb with cabinetry. The front wheels must be a minimum of 1/8″ (0.3 cm) off the floor.
7/16″ hex nut adjusts rear wheels
T30 bit adjusts front leveling legs
7/16″ open end wrench adjusts front leveling legs
NOTICE: The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1″. If the installation requires more than 84″ height, the installer should elevate the unit on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening. If you attempt to raise the unit more than 1″, you will damage the front leveling legs and the rear leveling wheels.

STEP 9 Install Door Trims
Ensure anti-tip brackets are engaged with the back of the unit.
6HH6HFWLRQ’RRU3DQHO$GMXVWPHQWVDQG7ULP Installation for details.

54

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

STEP 10 FINAL EXTERNAL UNIT PREPARATION

FOR FLUSH INSTALLATION: Make sure front surface

of the door is flush with the front face of surrounding

cabinets BEFORE securing brackets to the surrounding

cabinetry.

Compartment Door

Filter

Open the doors to the units. Locate ¿OWHUDQG¿OWHU

Filter Removal Tool

removal tool. Filter

should be as shown.

5RWDWH¿OWHUóWXUQ counterclockwise XVH¿OWHUUHPRYDOWRROLI needed).

Mounting Hook

/RFDWHEOXHDUURZRQ¿OWHU 5RWDWH¿OWHUWRDOLJQDUURZDV shown.
,QVHUW¿OWHULQWRSRVLWLRQDQG URWDWHóWXUQFORFNZLVHXVH ¿OWHUUHPRYDOWRROLIQHHGHG
5HWXUQ¿OWHUUHPRYDOWRROWRPRXQWLQJ hook.
Close the compartment door. Put the access cover back onto the unit
and secure with two 1/4″ hex head screws.

3XOO¿OWHUWRZDUGRXWR remove. NOTE: Water VVWHPZLOOQRWIXQFWLRQZLWKRXW¿OWHULQSODFH
Predrill 1/16″ holes is both the sides of the surround 1/2″ deep through holes in the enclosure.

CAUTION Use gloves and arm guard when
installing spacers.
Secure unit to surrounding cabinetry using the spacers and 1″ Phillips screws provided with the unit. On Single Door models: Secure the handle side first before moving the hinge side. On French Door models, open one door and secure that side before moving to the other side.
Open door to full extension and pass arm through opening between door and case to align spacers. Slide the spacers into place using the alignment features on the spacer and the side of the (A) housing until the spacer screw holes and housing screw holes are aligned. Drive the Phillips head screws through the housing into the surrounding cabinetry.
NOTE: This step does NOT replace the anti-tip safety hardware. Refer to Step 3 Installing Anti-Tip Bracket and Step 5 Inserting / Securing into Cabinet Surround for details on installing the anti-tip hardware.
A Housing

Access Cover

1/4″ Hex Screws

On the side of the access cover that will face the middle of the installation, drive two 1/4″ hex head screws. These screws will enhance attachment of mullion trim. Repeat on the second access cover.

Access Cover Hole Locations

Locating feature on the housing
31-1000731 Rev. 3

Locating feature on the spacer
Cabinet

A

Spacer

55

Installation Instructions – Dual Integrated Installation

STEP 10 FINAL EXTERNAL UNIT PREPARATION (Cont.)
Mullion Trim Installation
Open all doors and drawers. $OLJQWRSRI0XOOLRQ7ULPZLWKWRSRIFRQWUROSDQHOV ,QVWDOOPXOOLRQWULPEHWZHHQWKHWZRXQLWVESXVKLQJ
the dart in the area between the units.
(QVXUHWULPLVIXOOVHDWHGDJDLQVWFDVH$GMXVWLI necessary.

“Dart”

Mullion Trim

STEP 11 HANDLE INSTALLATION
Make sure the set screws in the handle caps are loosened. Place the handle over the fasteners on the door (we recommend putting the screw side of the handle toward the less visible side). Take care to support the handle so it doesn’t fall and scratch the appliance finish. Make sure both of the handle caps are resting on the face of the door.
Fastener
Set Screw
Lock one end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Keep supporting the handle as you lock the other end of the handle into position by tightening the set screw in the handle cap with the 1/8″ Allen wrench. Be sure not to over tighten.
Repeat these instructions on all other handles.

NOTE: Doors/Drawers not shown for clarity.
Open both enclosure doors to 90°. Snap the trim bracket between the water filter access
enclosures above displays.

STEP 12 TOE KICK INSTALLATION
A stainless steel toe kick and a magnet are included with each refrigerator. A full width toe kick (ZKN72V) for dual integrated installations can be purchased separately.
For individual toe kicks, adhere magnets to the back side of the toe kicks. The surface of the toe kick where the magnet is to be placed must be clean and free of foreign material. Center magnets vertically and horizontally.
Position toe kick(s) on bottom portion of front access covers.

If installation requires a 90° door opening, the hinge limiter pin(s) must be installed in the top hinge(s). – Open the door to expose the hole in the back hinge bracket and install the limiting pin. Pin must be fully seated in the hinge or the door will not close properly.
56

31-1000731 Rev. 3

Installation Instructions – Dual Integrated Installation

STEP 13 INTERNAL UNIT PREPARATION
Remove all tape, cardboard, and foam from each unit.
Remove boxed door bins from shelves. Unbox and install door bins.
STEP 14 START ICEMAKER
CAUTION To minimize the risk of personal
injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.
ATTENTION Afin de réduire le risque de blessure,
évitez tout contact avec les pièces mobiles du mécanisme d’éjection ou l’élément chauffant qui libère les cubes. Ne placez pas les doigts ou les mains sur le mécanisme de production de glace automatique lorsque l’électroménager est branché dans la prise électrique.
PRECAUCIÓN Para minimizar el riesgo de
lesiones personales, evite el contacto con las partes móviles del mecanismo eyector o con el elemento de calefacción que libera los cubos. No coloque los dedos ni las manos en el mecanismo de la máquina de hielo automática mientras el electrodoméstico se encuentre enchufado.
A newly-installed freezer may take 12­24 hours to begin making ice. The icemaker will produce seven cubes per cycle– approximately 15 cycles in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions. If the freezer is operated before the water connection is made to the icemaker, turn the ice maker off by pressing and holding the Zone Select pad until Ice Off app

References

• Café Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>