nVent EN2.0 Series Enhanced DIN Rail Surge Protection User Manual
- July 30, 2024
- nVent
Table of Contents
- ADDITIONAL RESOURCES
- UNPACKING THE NVENT ENLOGIC PDU
- BEFORE YOU BEGIN
- MOUNTING
- CONNECTING TO A POWER SOURCE
- CONNECTING TO A NETWORK
- ACCESSING AN NVENT ENLOGIC PDU USING A STATIC IP ADDRESS
- DAISY-CHAIN NETWORK COMMUNICATIONS
- WARRANTY INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
nVent EN2.0 Series Enhanced DIN Rail Surge Protection User Manual
ADDITIONAL RESOURCES
For more information about nVent Enlogic products and complete installation information, go to www.enlogic.com.
Refer to the EN2.0 Series User Guide for specific information on installation and operation of the PDU or visit www.enlogic.com.
Warranty information can be found at www.enlogic.com/enlogic- warranty.
UNPACKING THE NVENT ENLOGIC PDU
Unpackage the nVent Enlogic PDU and ensure that nothing is missing or damaged. If something appears to be missing or damaged, contact nVent Enlogic at info@enlogic.com.
The following is included:
- EN2.0 Series PDU
- Quick Start Guide
- Safety Information Sheet
- Warranty card
BEFORE YOU BEGIN
- Prepare the installation site: make sure it is not exposed to extreme temperature or humidity. Allow space around the nVent Enlogic PDU for cabling and outlet connections. Refer to the EN Series User Manual for full installation and operation information and safety instructions.
- Register your product online at www.enlogic.com/enlogic-warranty
MOUNTING
Mounting the PDU in the Server Cabinet without Mounting Brackets
The EN2.0 Series PDU comes with tool-less mounting pegs for ease and convenience.
-
Determine where the EN2.0 Series PDU will be mounted inside the server cabinet.
-
Insert the PDU mounting pegs into the mounting holes of the server cabinet.
Note : The distance between mounting pegs varies depending on PDU models. Full length PDU is 1555 mm, mid length is 1244 mm and half length is 622 mm. -
Pull the power cord through the cabinet and proceed with connecting to a power source.
Note : For specific mounting instructions for various rack manufacturers refer to www.enlogic.com.
Mounting the PDU in the Server Cabinet with Mounting Brackets
-
Determine where the EN2.0 Series PDU will be mounted inside the server cabinet. Hang the mounting brackets in the server cabinet using the mounting bracket hooks.
-
Attach the enclosed mounting brackets to the server cabinet using the screws provided.
-
Insert the PDU mounting pegs into the mounting holes of the server cabinet.
Note : The distance between mounting pegs varies depending on PDU models. Full length PDU is 1555 mm, mid length is 1244 mm and half length is 622 mm. -
Pull the power cord through the cabinet and proceed with connecting to a power source.
Note : For specific mounting instructions for various rack manufacturers refer to www.enlogic.com.
CONNECTING TO A POWER SOURCE
When connecting the nVent Enlogic PDU to a Power Source, make sure that you have enough length in the PDU power cord to reach the PDU power source.
-
Turn the feed circuit breaker off. Make sure that all circuit breakers on the nVent Enlogic PDU are set to ON.
-
Connect each nVent Enlogic PDU device to an appropriately rated branch circuit.
Note : Refer to the label on the PDU for acceptable input ratings. -
Turn the feed circuit breaker on. The OLED screen will display a loading status screen when the PDU is loading. When complete, the Main Menu will display on the OLED.
Note : If the PDU is a switched PDU, the lights corresponding to each outlet will consecutively turn on to indicate power before displaying a steady color.
CONNECTING TO A NETWORK
The EN2.0 series PDU is DHCP compatible.
- Connect a standard Ethernet patch cable to the Ethernet port on the EN2.0 Series PDU.
- Connect the other end of the Ethernet cable to your LAN.
- Make sure the Ethernet port on the PDU shows a solid green light on the left and a flashing yellow light on the right to indicate successful connectivity to the network.
- Look up the IP address on the OLED Display, using the menu buttons to go to: Setup>Network>IPv4 or IPv6, as applicable.
- In a standard web browser, enter the PDU IP address and proceed to configure the PDU.
Note : The default username is admin. The default password is 12345678.
ACCESSING AN NVENT ENLOGIC PDU USING A STATIC IP ADDRESS
-
Connect a standard Ethernet cable to the Ethernet port on the EN2.0 Series PDU and the other end of the Ethernet cable directly to your laptop/PC.
Note : A cross over cable is not required. -
When the PDU completes a live connection, the Ethernet port on the PDU shows a solid green light on the left and a flashing yellow light on the right to indicate successful connectivity.
-
When connected, and with no DHCP service found, the PDU will revert to a static IP address of 192.168.0.1
-
Assign your laptop/PC’s Ethernet port an IP address in the 192.168.0.2-254 range.
Note : Do NOT assign 192.168.0.1 to your laptop/PC. -
In a standard web browser, enter the URL ‘http://192.168.0.1’ and configure the PDU, or access the CLI using SSH at 192.168.0.1:22
Note : The default username is admin. The default password is 12345678. Configuring the PDU with a static IP address overrides the default IP address.
DAISY-CHAIN NETWORK COMMUNICATIONS
To connect up to 64 PDUs of the same SKU through a single IP address:
- Configure the PDU that will be first in line on the 10/100/1000 daisy-chain.
- When the initial PDU is configured, connect an Ethernet cord from the 10/100 port on the configured PDU to the 10/100/1000 port on the next PDU in the daisy-chain line.
- Repeat step 2, connecting PDUs from the 10/100 port to the 10/100/1000 port for up to 64 PDUs.
Note : Length of the Ethernet cords connecting the PDUs must be less than 6 m (20 feet).
WARRANTY INFORMATION
CIS Global, LLC (CIS) warranties that the nVent Enlogic EN2.0 equipment provided shall be free from manufacturing defects for a period of five (5) years from the invoice date to the original purchaser. Product registration may be completed online at www.enlogic.com.
CIS’s warranty obligations here under are contingent upon the following conditions: (1) CIS is promptly notified of the defect; (2) Purchaser establishes to CIS’s reasonable satisfaction that any goods have been properly installed, maintained and operated; and (3) Purchaser returns the defective goods or any part thereof to CIS. Upon a determination by CIS that a product is not as warranted, CIS shall, at its exclusive option, replace or repair said defective product or parts thereof. This warranty is void in the case of abuse, misuse, abnormal usage, faulty installation or repair by unauthorized persons, or if for any other reason CIS determines that said product is not operating properly as a result of causes other than defective manufacture.
This warranty shall apply exclusively to nVent Enlogic brand products sold to Purchaser by CIS Global, LLC or any company controlled by or in common control with CIS or an CIS subsidiary (collectively, “CIS”). CIS shall not have any liability or obligation to Purchaser, under this warranty or otherwise, with respect to any defect or failure of performance in products which are not sold or manufactured by CIS, including any such products which are commingled with or incorporated into any CIS or nVent Enlogic brand products, or any products into which CIS products are incorporated as a system component or otherwise.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, IT BEING UNDERSTOOD THAT ALL SUCH OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED. IN NO EVENT SHALL NVENT ENLOGIC BE LIABLE TO PURCHASER FOR ANY DIRECT, COLLATERAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH PURCHASER’S USE OF ANY OF THE PRODUCTS LISTED HEREIN, OR FOR ANY OTHER CAUSE WHATSOEVER RELATING TO THE SAID PRODUCTS. NEITHER NVENT ENLOGIC NOR ITS REPRESENTATIVES SHALL BE LIABLE TO THE PURCHASER OR ANYONE ELSE FOR ANY LIABILITY, CLAIM, LOSS, DAMAGE OR EXPENSE OF ANY KIND, OR DIRECT COLLATERAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RELATIVE TO OR ARISING FROM OR CAUSED DIRECTLY OR INDIRECTLY BY SAID PRODUCTS OR THE USE THEREOF OR ANY DEFICIENCY, DEFECT OR INADEQUACY OF THE SAID PRODUCTS. IT IS EXPRESSLY AGREED THAT PURCHASER’S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION RELATING TO THE PURCHASE AND/OR USE OF ANY OF THE PRODUCTS LISTED HEREIN FROM NVENT ENLOGIC SHALL BE FOR DAMAGES, AND NVENT ENLOGIC’S LIABILITY FOR ANY AND ALL LOSSES OR DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, INCLUDING WHETHER SUCH DAMAGES ARE CLAIMED, ASSERTED OR BROUGHT IN AN ACTION OR CLAIM IN TORT OR CONTRACT, OR ON THE WARRANTY ITSELF, OR UNDER ANY OTHER LAW OR FORM OF ACTION, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT IN RESPECT TO WHICH THE CLAIM IS MADE, OR AT THE ELECTION OF NVENT ENLOGIC, THE RESTORATION OR REPLACEMENT OR REPAIR OF SUCH PRODUCT.
This warranty is governed by and construed in accordance with the laws of the State of Arizona, without regard to conflict of law principles. The parties to this warranty agree that the United Nations Convention on Contracts for the International Sale of Goods is hereby excluded in its entirety from application to this warranty. All disagreements and disputes arising out of or in connection with this warranty shall be finally settled by arbitration. Unless otherwise prohibited by law, the arbitration shall be: (i) held in Tucson, Arizona; (ii) conducted in accordance with Arizona law; (iii) conducted in the English language; (iv) settled under the Rules of Arbitration of the American Arbitration Association (“Rules”); and (v) heard by one arbitrator appointed in accordance with the Rules. The decision of the arbitrator shall be final and binding upon the parties. If part of this warranty is held to be invalid or unenforceable, such invalidity or unenforceability shall not invalidate or render unenforceable the entire warranty, but rather the warranty shall be construed as if not containing the particular invalid or unenforceable provision.” If this warranty is translated into a language other than English, the English version will prevail to the extent that there is any conflict or discrepancy in meaning between the English version and any translation thereof.
America
amersales@nVent.com
Asia Pacific
apacsales@nVent.com
Australia & New Zealand
anzsales@nVnet.com
Europe & Middle East
cis.emea.sales@nVent.com
India
indiasales@nVent.com
©2024 nVent. All nVent marks and logos are owned or licensed by nVent Services
GmbH or its affiliates. All other trademarks are the property of their
respective owners.
nVent reserves the right to change specifications without notice.
nVent-IM-N01915-iPDU-QuickStartInstallGuide-ML-2407