Landmann 28343 Big Sky Wildlife Georgia Clay Instruction Manual

: July 27, 2024
: LANDMANN

Table of Contents

Landmann 28343 Big Sky Wildlife Georgia Clay
Product Information
Product Usage Instructions
Models
SAFETY INSTRUCTION
PARTS LIST
ASSEMBLY INSTRUCTIONS
HELPFUL HINTS FOR USAGE
COOKING GRATE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Landmann 28343 Big Sky Wildlife Georgia Clay

Product Information

Specifications:

Model: Landmann 28343
Parts Included: Spark Guard Cover, Cooking Grate, Fire Pit, Ring Sections, Multi-Purpose Poker, Cooking Grate Pins, Legs, Bolts, Nuts, Washers
Material: Steel
Finish: Sandpoint Finish

Assembly Instructions:

Take each of the (3) legs and bolt them to the fire pit using (6) washers and (6) nuts. Tighten securely.
Assemble (1) ring section to the fire pit using (2) bolts, only loosely tighten the bolts.
Repeat Step 2 for the remaining (2) ring sections. Make sure the (3) ring sections fit together to form a continuous ring. Tighten all bolts securely.
Take each of the (3) cooking grate pins and thread them into the nuts welded on the inside of the fire pit. Do not over tighten.
Place spark guard on cooking grate pins. The spark guard’s purpose is to keep sparks contained in the fire pit. Please use at all times.
Before using, place 5 lbs of sand on the bottom of the fire pit. The sand insulates the area below the pit and protects against the corrosive nature of the ashes.

Product Usage Instructions

Multi-Purpose Poker:
The poker can be used not only for shifting and tending the fire but also for removing the cooking grate, lifting off the spark guard, or pulling Big Sky to another location.
Cooking Grate:
If you would like to grill, place the cooking grate on the cooking grate pins. Please remove the cooking grate when not grilling.
Sandpaint Finish:
Note: Since the heat intensity from the fires will vary depending on the type and amount of fuel used, you may experience minimal peeling or flaking of the paint. This is normal and will not affect the safety or performance of this fire pit.

FAQ:

Q: Can I use wood pellets as fuel in this fire pit?
A: It is recommended to use natural wood logs as fuel for this fire pit for optimal performance and safety.
Q: How do I clean the fire pit after each use?
A: Allow the ashes to cool completely before disposing of them. Use a brush to sweep out any remaining ashes and debris from the fire pit.

Models

28335
28336
28337
28345
28346
28347
28348
28338
28339
28340
28341
28342
28343

SAFETY INSTRUCTION

READ FIRST!
RULES FOR SAFE OPERATION

FOR OUTDOOR USE ONLY!
USE ONLY ON BRICK, CONCRETE, STONE OR OTHER MASONRY SURFACES!
DO NOT USE ON LAWNS, WOODEN DECKS, OR ASPHALT!
KEEP BIG SKY AWAY FROM BUILDINGS, FLAMMABLE ITEMS AND VEHICLES.
THE BIG SKY FIRE PIT IS FOR ADULT USE ONLY.
DO NOT LEAVE UNATTENDED AT ANY TIME WHILE IN USE.
KEEP SPARK GUARD ON BIG SKY WHILE IN USE.
DO NOT USE IN WINDY CONDITIONS!
DO NOT OVERLOAD OR USE FOR BURNING GARBAGE.
NEVER USE GASOLINE, ALCOHOL, OR VOLATILE FLUIDS TO START FIRES.
NEVER USE UNDER LOW-HANGING TREE BRANCHES, TRELLIS, OR OVERHANGS OF ANY KIND INCLUDING COVERED PORCHES.
USE CAUTION WHEN TENDING THE FIRE, AS SURFACES WILL BE HOT WHILE IN USE.
BEFORE EACH USE MAKE SURE BIG SKY IS IN GOOD WORKING CONDITION.
USE CAUTION AFTER THE FIRE HAS BEEN EXTINGUISHED, SURFACES WILL REMAIN HOT FOR SOME TIME.

PARTS LIST

When unpacking the Big Sky from the carton, make sure you find and become familiar with all the pieces listed below:

TOOLS NEEDED FOR ASSEMBLY:

Adjustable Wrench
Phillips Screw Driver

ASSEMBLY INSTRUCTIONS

STEP 1
Take each of the (3) legs and bolt them to the fire pit (as shown in the diagram to the left) using (6) washers and (6) nuts. Tighten securely!
STEP 2
Assemble (1) ring section to the fire pit using (2) bolts, only loosely tighten the bolts.
STEP 3
Repeat STEP 2 for the remaining (2) ring sections. Make sure the (3) ring sections fit together to form a continuous ring. Tighten all bolts securely!
STEP 4
Take each of the (3) cooking grate pins and thread them into the nuts welded on the inside of the fire pit. Do not over-tighten!
STEP 5
Place spark guard on cooking grate pins. The spark guard’s purpose is to keep sparks contained in the fire pit. PLEASE USE at all times.
STEP 6
Before using you must place 5 lbs of sand on the bottom of the fire pit. The sand insulates the area below the pit and protects against the corrosive nature of the ashes.

MULTI-PURPOSE POKER
The poker can be used not only for shifting and tending the fire, but also for removing the cooking grate, lifting off the spark guard, or pulling Big Sky to another location.

HELPFUL HINTS FOR USAGE

ADDING SAND TO THE BOTTOM OF THE FIRE PIT HELPS PROTECT AGAINST THE CORROSIVE NATURE OF THE ASHES AND WILL EXTEND THE LIFE OF THE PIT.
BURN YOUR FIRE PIT 3 TIMES BEFORE USING TO COOK ON.
STORE AWAY OUT OF THE WEATHER AND ELEMENTS.
DO NOT LET YOUR FIRE PIT FILL WITH WATER.
DO NOT DUMP ASHES WHERE THEY COULD START A FIRE.
DISPOSE OF ASHES IN PROPER RECEPTACLE ONLY AFTER ASHES HAVE COOLED.

COOKING GRATE

If you would like to grill, place the cooking grate on the cooking grate pins.

PLEASE NOTE:
Please remove the cooking grate when not grilling.

SANDPAINT FINISH

Note:
Since the heat intensity from the fires will vary depending on the type and amount of fuel used, you may experience minimal peeling or flaking of the paint. This is normal and will not affect the safety or performance of this fire pit.

Congratulations on your purchase of the Big Sky Fire Pit! At Landmann USA, we strive to provide you with an easy-to-use, easy-to-assemble product. However, in the unlikely event your package should have a missing or defective part, please contact us at: customerservice@landmann- usa.com -OR- 1-800-321-3473 M-F 8-5 Eastern Time Proof of purchase may be required. Thank you!

Landmann USA
Cartersville, GA 30120

Made in China.