DONGGUAN 2A378 Hear D I Kaibo Verse Hear Headphones User Manual

DONGGUAN 2A378 Hear D I Kaibo Verse Hear Headphones User Manual

Using Instructions

• Paring headphone with Hear DI
  Press and hold the power key of headphone and dongle at the same time. At this time, the LED indicators of both sides will alternate red and green lights, and automatically pairing with each other. After successful pairing, the Hear DI green light stays on, and the headphone green light blinks every 5 seconds

• Hear DI wireless connection
  Place the Hear DI near the source of the sound (such as a TV or computer), and the collected sound will automatically become louder and transmitted to the headphone via Bluetooth. >>>

• Hear DI wired connection
  Hear DI can connect to a TV or other media/MP4 players through the 3.5mm AUX audio cable included in the accessory. Dongle will automatically amplify the sound source and transmit it to the headphone

• Using Hear DI in charging state
  Hear DI can be used normally while charging. At this time, the indicator light shows that the green light is constantly on and the red light is flashing slowly After being fully charged, the red light goes out

• Headphone used alone
  When the Hear DI is turned off separately in pairing mode, the headphone will have red and green flashing lights, so that they can be connected to the phone for use.

Product Instructions

Hear DI Specification

Mode: Dongle

Connection method: Bluetooth/3.5mm AUX
Bluetooth Version: 5.2| Bluetooth connection distance: 10 meters
Microphone sensitivity: -38db±2db| Weight: 13g
Battery: lithium battery| Battery Capacity: 150mAh
Battery Life : 8-10 hours|
Time to Full Charge: About 2 hours| Button Mode: Mechanical Button
Electrical specifications: 5V/1A| Waterproof level: IPX4
Charge port: USB-C

FEATURE

Green
Power OFF| Press & hold power button for 3 seconds| Lights OFF
Pair with Headphone| Pairing| Pairing after Dangle is power ON| Slowing green [light reds
Connected| When the earphones are on and close to Dangle, two devices paired with each other automatically| Solid Green
Dangle powers OFF after 3 minutes of disconnection| Blinks Red
Call| Answer/End Calls| Press power button one time|
End  Calls| Press power button twice| –
3.Smm AUX Connection Mode| Plug in 3.SmmAUX to receive audio| Solid Green
Bluetooth Connection Mode| within l the Dangle wtn Place t     DSO mm of the sound source| Solid Green
Battery| Battery Low| –| Red light blinks every 10 seconds
Charging| –| Flashing red ang green [this
Full Charged| –| Solid Red
When USB-C plug in, Dongle start charging
Use while Charging| Used normally when charging| Solid Green ,flashing red ang green lights
Volume| Volume +| Press + button one time| –
Volume| Press power button one time| –
Factory reset setting| Double click ‘-.’ button and then power off automatically in pairing state| Flashing red ang green lilghts and then OFF

Storage and Maintenance

• To prevent possible hearing damage or loss do not listen at high volume levels for long periods of time. Sound can also be distorted at too high a volume
• After storing for a long time, please recharge before using.
• Pay attention to the placement environment, as excessively cold, hot, or humid environments may shorten the battery life. Keep the charging port dry before charging to reduce the risk of headphone damage.
• Voltage/Current 5V/1A

Warning

• Bone conduction sound amplifier do not repair the user’s previous hearing, nor do they prevent or improve hearing damage caused by organ conditions. In most cases, infrequent use of sound amplifier cannot melodize user benefits. The use of assistive hearing equipment is only a part of hearing rehabilitation, and requires auditory training and lip reading guidance to assist
• Bone conduction sound amplifier are not waterproof and should not be wom in heavy rain, bathing, showering, diving, or other environments that may expose them to amount of water. Because it may cause damage when expased to moisture Protect your bone conduction sound amplifier from impact or vibration, and prevent it from falling.
• When removing the device, turn off the device first. If you do not use a Bone conduction sound amplifier for a long time, you should fully charge it and place it in the packaging box when it is turned off
• The mode key and volume button should be used correctly, and should be Turned on or off as gently as possible. Avoid excessive force or pulling, which may cause damage to the equipment
• Unless otherwise specified accessories are used, using transducers, cables, and bone conduction sound amplifier together may result in an increase in bone conduction sound amplifier emissions or a decrease in immunity

Features

red
ang green lights
Connected| When the earphones are on and close to Dongle, two devices paired with each other automatically| Solid Green
Dongle powers OFF after 3 minutes of disconnection| Blinks Red
Call| Answer/End Calls| Press power button one time| –
End Calls| Press power button twice| –
3.5mm AUX Connection Mode| Plug in 3.5mmAUX to receive audio| Solid Green
Bluetooth Connection Mode| Place the Dongle within 50mm of the sound source| Solid Green
Battery| Battery Low| –| Red light blinks every 10 seconds
Charging| –| Flashing red ang green lights
Full Charged| –| Solid Red
When USB-C plug in, Dongle star charging
Use while Charging| Used normally when charging| Solid Green, flashing red ang green lights
Volume| Volume 4.| Press + button one time| –
Volume| Press power button one time| –
Factory reset setting| Double click’-‘ button and then power off automatically in pairing state| Flashing red ang green lights and then OFF

Storage and Maintenance

• To prevent possible hearing damage or loss, do not listen at high volume levels for long periods of time Sound can also be distorted at too high a volume
• After storing for a long time, please recharge before using
• Pay attention to the placement environment, as excessively cold, hot, or humid environments may shorten the battery life. Keep the charging port dry before charging to reduce the risk of headphone damage.
• Voltage/Current 5V/1A

Warning

• Bone conduction sound amplifier do not repair the user’s previous hearing, nor do they prevent or improve hearing damage caused by organ conditions. In most cases, infrequent use of sound amplifier cannot maximize user benefits. The use of assistive hearing equipment is only a part of hearing rehabilitation, and requires auditory training and lip reading guidance to assist
• Bone conduction sound amplifier are not waterproof and should not be worn in heavy rain, bathing, showering, diving, or other environments that may expose them to amount of water. Because it may cause damage when exposed to moisture. Protect your bone conduction sound amplifier from impact or vibration, and prevent it from falling.
• When removing the device, turn off the device first. If you do not use a Bone conduction sound amplifier for a long time, you should fully charge it and place it in the packaging box when it is turned off
• The mode key and volume button should be used correctly, and should be turned on or off as gently as possible. Avoid excessive force or pulling, which may cause damage to the equipment
• Unless otherwise specified accessories are used, using transducers, cables, and bone conduction sound amplifier together may result in an increase in bane conduction sound amplifier emissions or a decrease in immunity

Features Operating Instructions| Light Indicator| Sound Notification
---|---|---
General Settings| Turn On| Press & hold power button for 3 seconds| Blinks Green| Tower on’
Turn Off| Press & hold power button for 3 seconds| Blinks Red| ‘Power off’
Pairing| Connection in
Progress| Earbuds will automaticaly enter bluetooth
pairing when powered on| Slow flashing red and green lights| “Pairing’
Connection Success| Select’ Kaibo Verse Plus’ In device
settings to connect| Green light flashes once every 3 seconds| ‘Connected’
Disconnect| DISCO011ttl bluetooth connection from
previously connected device| Blinks Green| ‘Disconnected’
If no connection over 3 minutes, earbuds
will automatically turn off| Bird’s Red| ‘Power off’
Cal| Answer/
End Cols| Press power button one time| –| –
Reject Calls| Press power button two times| –| –
Music
Battery| Flay / Pause| Press power button one time| •| 1 Doo
Skip forward
Low Battey| Press power button two times
.| •Red          s.Red light dashes onceevery 10 seconds| 2 Doo’Battery lovf(Once every 30 ieconds)
Charging / My charged : Solid Red / Solid Green
When Type C plug in, earbuds start chargirq
Factory reset setting| When earbuds is turned off, press and
hold power button for 10 seconds| Red Fight flashes 4 times| Tower on’ Wring’ 4 Doo ‘Power off
Voice assistant| Press right bud for 3 seconds| •| 3 Doo
Model  No: Hear BC-V

Bluetooth Version : V5.2| Wire Range :10 Meters / 33 Feet
Frequency Response :100 Hz-20 KHz| Bluetooth Response : 2402-2.480 GHz
Impedance : 80| Speaker Driver : 014.0mm BCT
Microphone Sensitivity :40 dElt 2 dB| Weight : 27.2g
Battery Capacity : 150 mAh| Battery : lithium battery
Play   Time : About 8 Hours| Charging Time : About 1.5 Hours
Button Style : Button+Smart Touch| Waterproof Level : IPSS
Electrical Specifications : W / 1A| C ompatible Profiles : HIP 1. 7,HSP 1. 2, A2DP 1. 3, AVRCP 1.6

APP Related

• Open the App Store, search for Kaibo Audio Connect1, and select from three preset equalizers to choose the right sound performance according to your preference and environment.
• In addition to the three equalization modes: Acoustic, Sport, and Manual you can allso check the remaining power and update the firmware.
• Please refer to the instructions on the official website to update the firmware and reboot the headphones after the update is completed.

FCC Warning

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1 : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>