VALDUS P68 LED Display White Bluetooth Wireless Earphone Instruction Manual
- July 25, 2024
- VALDUS
Table of Contents
VALDUS P68 LED Display White Bluetooth Wireless Earphone
Product Specifications
Product name: P68 wireless bluetooth headset
Battery capacity: 40mAh charging case 250mAh
Charging voltage/current: 5V,.,1 A
Frequency response range: 20hz- 20khz
Impedance of products : 16 o soil by 15%
Sensitivity : 103+3dB At1000Hz at0.126v
Operating/storage temperature: – 10’C- 50’C
Battery life: music play about 300 minutes/talk time about 240
minutes/standby time about 240 hours
Reception distance: 15m (standard environment)
Weight: 45g (charging case) 7.0g (binaural)
Transmission range : 2402- 2408MHz
Support protocol: HSP/HFP/A2DP(SBC, AAC/AVRCP
Transmission frequency: 24GHz band(2.4000- 2.48356Hz)
Charging time : 60 minutes for earphone, 90 minutes for charging case
Product size: 46x21x50(mm)
- the above data is for reference only, the specific object shall prevail
Pair Connection
Take out the headset from the charging compartment and automatically start pairing
Pair left and right ears
Open the charging compartment and take out the earphones. After taking out the earphones, the red and blue lights flash alternately. When one light is off and the other light is on, it indicates that the pairing is successful.
Connect your phone
Turn on Bluetooth in the settings and find the model “P68” in the Bluetooth list to connect. After the connection is successful, it will automatically connect next time.
Functional Operation
Answer/hang up
Touch once, double- click to reject the call
Play/ Pause
Touch once to play or pause
Previous Piece
Left earphone touch 2 times
Next track
Right earphone touch 2 times
Increase the volume
Left earphone touch 3 times
Next track
Right earphone touch 3 times
Summon Siri
Press and hold for two seconds
On/off
Press and hold for five seconds
Replace ear sleeve
To remove the earbud sleeve, pull down firmly.
To attach the earbud sleeve, press and hold until it fits.
Choose the eartip sleeve that fits your ears most comfortably
Charge the headset
Put the lid in the bin and charge automatically.
It will be fully charged in about 1 hour. The green light will indicate that
it is fully charged.
Charge the charging case
Use the Type- c interface data cable to charge.
During charging, the power digital display flashes, indicating that 100 is
full, and it takes about 1.5 hours to fully charge.
Matters needing attention
Please store and use this product at room temperature.
Do not expose this product to rain or moisture.
Do not throw, avoid product damage caused by falling Do not discard it at
will, or put it at high temperature (temperature above 60 degrees) and fire to
avoid danger;
Do not disassemble, repair or modify this product yourself.
Do not use chemical solvent to wipe this product If not used for a long time,
please charge the product once every 2 months
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, induding interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radionv technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co- located or conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>